Drive Shaft - BE33.30-P-1000-04C

WARNING: This page is about a different car, the 2023 Mercedes-Benz GLC300, 2022 Mercedes-Benz GLC300, 2021 Mercedes-Benz GLC300, 2020 Mercedes-Benz GLC350e, and 2020 Mercedes-Benz GLC300. However, it is still accessible from the selected car via links, so may be relevant.

Model 204, 205, 206, 207, 212, 213, 216, 217, 218, 221, 222, 223, 238, 253, 257, 290

INTERMEDIATE SHAFT

Number	Designation				Model 204	Model 205
BE33.30-P-1001-04C	Length "a" for grooved ball bearing wheel offset	With an intermediate shaft length of	472.0 mm	mm	^-	^-
			478.5 mm	mm	-	334, 5...334, 7
			479.3 mm	mm	-	-
			504.3 mm	mm	368, 5...368, 7	-
			510.0 mm	mm	-	366, 0...366, 2

INTERMEDIATE SHAFT

Number	Designation				Model 206	Model 207
BE33.30-P-1001-04C	Length "a" for grooved ball bearing wheel offset	With an intermediate shaft length of	472.0 mm	mm	342, 9...343, 1	^-
			478.5 mm	mm	-	-
			479.3 mm	mm	350, 2...350, 4	-
			504.3 mm	mm	-	368, 5...368, 7
			510.0 mm	mm	-	-

INTERMEDIATE SHAFT

Number	Designation				Model 212	Model 213
BE33.30-P-1001-04C	Length "a" for grooved ball bearing wheel offset	With an intermediate shaft length of	472.0 mm	mm
			478.5 mm	mm	-	334, 5...334, 7
			479.3 mm	mm	-	-
			504.3 mm	mm	368, 5...368, 7	-
			510.0 mm	mm	-	366, 0...366, 2

INTERMEDIATE SHAFT

Number	Designation				Model 216	Model 217
BE33.30-P-1001-04C	Length "a" for grooved ball bearing wheel offset	With an intermediate shaft length of	472.0 mm	mm	^-	^-
			478.5 mm	mm	-	-
			479.3 mm	mm	-	-
			504.3 mm	mm	368, 5...368, 7	-
			510.0 mm	mm	-	366, 0...366, 2

INTERMEDIATE SHAFT

Number	Designation				Model 218	Model 221
BE33.30-P-1001-04C	Length "a" for grooved ball bearing wheel offset	With an intermediate shaft length of	472.0 mm	mm
			478.5 mm	mm	-	-
			479.3 mm	mm	-	-
			504.3 mm	mm	368, 5...368, 7	368, 5...368, 7
			510.0 mm	mm	-	-

INTERMEDIATE SHAFT

Number	Designation				Model 222	Model 223
BE33.30-P-1001-04C	Length "a" for grooved ball bearing wheel offset	With an intermediate shaft length of	472.0 mm	mm	-	-
			478.5 mm	mm	-	-
			479.3 mm	mm	-	350, 2...350, 4
			504.3 mm	mm	-	-
			510.0 mm	mm	366, 0...366, 2	-

INTERMEDIATE SHAFT

Number	Designation				Model 238	Model 253
BE33.30-P-1001-04C	Length "a" for grooved ball bearing wheel offset	With an intermediate shaft length of	472.0 mm	mm
			478.5 mm	mm	334, 5...334, 7	334, 5...334, 7
			479.3 mm	mm	-	-
			504.3 mm	mm	-	-
			510.0 mm	mm	366, 0...366, 2	366, 0...366, 2

INTERMEDIATE SHAFT

Number	Designation				Model 257	Model 290
BE33.30-P-1001-04C	Length "a" for grooved ball bearing wheel offset	With an intermediate shaft length of	472.0 mm	mm
			478.5 mm	mm	334, 5...334, 7	334, 5...334, 7
			479.3 mm	mm	-	-
			504.3 mm	mm	-	-
			510.0 mm	mm	366, 0...366, 2	366, 0...366, 2