Shop-Made Tools: Passenger Cars - WF58.50-Z-0998AZ
WARNING: This page does not describe the selected car, but rather 12 other vehicles, including the 2023 Mercedes-Benz CLA45 AMG, 2023 Mercedes-Benz CLA35 AMG, 2023 Mercedes-Benz CLA250, 2022 Mercedes-Benz CLA45 AMG, and 2022 Mercedes-Benz CLA35 AMG. However, it is still accessible from the selected car via links, so may be relevant.
Mode All
| Change centering disk for the electronic inclination measuring instrument's measuring plate | MODEL 163 with CODE (612b) Xenon headlamp unit | WF58.50-P-0021-01GH | |
| Shop-made jack-up shoe | MODEL 116 | WF58.50-P-0060-01A | |
| Shop-made jack-up shoe | MODEL 124, 129, 140, 201, 202, 208 | WF58.50-P-0060-01B | |
| Guard plate for radiator/condenser | MODEL ALL | WF58.50-P-0110-01A | |
| Protective plate for cooling module | Model 205, 212, 213, 217, 218, 222, 223, 238, 253, 257, 290 | WF58.50-P-0110-04A | |
| Spacer screw for securing the lowered front axle bracket to the vehicle floor | MODEL 168 with ENGINE 166, 668 | WF58.50-L-0110-05VA | |
| Probe plunger and sleeve for cylinder head bolt hole threads | MODEL 203, 209, 211... | WF58.50-P-0130-01A | |
| Round bar for knocking steel ball out of main oil gallery | MODEL 124, 163, 169, 202, 203, 209, 210, 211, 220, 245, 408, 461, 463... | WF58.50-P-0140-01A | |
| Spacer for engine supporting bar | MODEL 140 | WF58.50-P-0145-01A | |
| Extension for counterholder | MODEL 163, 170, 171, 202, 203, 208, 209, 210, 211, 215, 216, 220, 221, 230, 240, 463... | WF58.50-P-0330-02A | |
| Degrees scale for vibration damper | MODEL 124, 140, 202, 210... | WF58.50-P-0330-03A | |
| Hook for hooking up the steering knuckle | MODEL 210.08/28 | WF58.50-P-0400-01A | |
| Drift for knocking in camshaft end cover | MODEL 124, 163, 202, 203, 209, 210, 211, 219, 220, 461, 463... | WF58.50-P-0520-01A | |
| Oil filter cap with test connection for oil pressure measurement | MODEL 124, 202, 210 with ENGINE 111 | WF58.50-P-0520-01B | |
| Line for bleeding low pressure fuel circuit | MODEL 168 with ENGINE 668.940/941 MODEL 414.700 with ENGINE 668.914 | WF58.50-P-0716-01GD | |
| Test wiring harness for testing fuel injection valves | MODEL 129, 140, 170, 202, 208, 210, 463, 638... | WF58.50-P-0761-01A | |
| Modifying support plate for transfer case | MODEL 203.08/09/28/29, 211.08/09/28/29, 220.08/18 | WF58.50-P-1000-02P | |
| Pin for locking poly-V belt tensioning device | MODEL 163, 166, 172, 202, 203, 204, 207, 209, 210, 211, 212, 218, 219, 220, 221, 461, 463, 638... | WF58.50-P-1325-02A | |
| Modifying long wedge for adjusting seal on sliding/pop-up roof cover | MODEL 208.3 | WF58.50-P-1360-01K | |
| Wrench for removing exhaust manifold | MODEL 220.028/128 | WF58.50-P-1410-01A | |
| Double hexagon wrench to remove pulley | MODEL 163, 164, 215, 220, 230... | WF58.50-P-1540-01I | |
| Oil filter cap with test connection for oil pressure measurement | MODEL 124, 202, 210 with ENGINE 111 MODEL 129, 140 with ENGINE 120 | WF58.50-P-1800-01A | |
| Remote thermometer for oil temperature measurement | MODEL 169.0/3, 245.2 with ENGINE 266.920/940/960/980 | WF58.50-P-1801-01AK | |
| Oil filter cap with connection hole for measuring oil pressure | MODEL 124 with ENGINE 605, 606 MODEL 202 with ENGINE 604, 605 | WF58.50-P-1840-01A | |
| De-oil housing for radiator and heating system | MODEL 163, 164, 202, 203, 209, 210, 211, 219, 220, 221, 251, 461, 463... | WF58.50-P-2000-01A | |
| Connection fitting for automatic transmission fluid pipes | MODEL all | WF58.50-P-2020-01A | |
| Container for escaping engine oil during oil filter change | MODEL 117, 156, 176, 246 with ENGINE 607 | WF58.50-P-2041-01A | |
| Wooden block for supporting engine | MODEL 168 with ENGINE 166, 668 MODEL 414.700 with ENGINE 166.961/991, 668.914 | WF58.50-L-2610-01VA | |
| Impact drift for cup of inductive sensor | MODEL 124, 129, 140, 202 with TRANSMISSION 717.4 | WF58.50-P-2630-01A | |
| Hook for loading the leaf spring | MODEL 124, 129, 140, 202, 461, 463... | WF58.50-P-2650-01A | |
| Arresting stud for intermediate shift lever | MODEL 124, 129, 140, 202, 461, 463... | WF58.50-P-2660-01A | |
| Arresting stud for intermediate shift lever | MODEL 124, 129, 202 with TRANSMISSION 717.44 | WF58.50-P-2660-01B | |
| Centering tool for installation of intermediate shift levers | MODEL 124, 129, 140, 202, 461, 463... | WF58.50-P-2660-02A | |
| Impact drift for radial sealing ring of speedometer drive | MODEL 124, 129, 140 with TRANSMISSION 722.5 | WF58.50-P-2730-01A | |
| Impact drift for radial lip-type sealing ring of brake band piston B2 | MODEL 124, 129, 140, 460, 461, 463, 901, 902, 903, 904... | WF58.50-P-2750-01A | |
| Assembly plate for freewheel inner race | MODEL 124, 129, 140, 210, 460, 461, 463, 601, 602, 901, 902, 903, 904... | WF58.50-P-2750-02A | |
| Bracket for transmission housing | TRANSMISSION 722.6 TRANSMISSION 722.6 | WF58.50-P-2750-03A | |
| Mounting plate for securing transmission | TRANSMISSION 722.626 | WF58.50-P-2750-04A | |
| Bowden cable for trailer coupling release mechanism | MODEL 211, 215, 220, 221... | WF58.50-P-3111-01M | |
| Puller for pressing spring control arm out of steering knuckle | MODEL 230 with CODE (P99) Special model "AMG Black Series" | WF58.50-P-3315-01RBS | |
| Caulker for securing twelve-point collared nut | MODEL 210 | WF58.50-P-3330-01A | |
| Shim for MZ elements | MODEL 220.8 | WF58.50-P-3330-05A | |
| Drilling template for front wheelhouse | MODEL 220.8 | WF58.50-P-3330-06A | |
| Shell halves (2 ea.) for pressing off and caulking the inner constant velocity joint. | MODEL 117, 118, 129, 140, 156, 166, 167, 170, 171, 172, 176, 177, 202, 203, 204, 205, 206, 207, 208, 209, 210, 211, 212, 213, 214, 215, 216, 217, 218, 219, 220, 221, 222, 230, 231, 236, 238, 246, 247, 253, 254, 257, 290, 292, 447... | WF58.50-P-3530-01A | |
| Staking tool for securing joint hub on rear halfshaft | MODEL 117, 118, 156, 166, 167, 170, 171, 172, 176, 177, 203, 204, 205, 206, 207, 208, 209, 211, 212, 213, 214, 215, 216, 217, 218, 219, 220, 221, 222, 230, 231, 236, 238, 246, 247, 253, 254, 257, 290, 292, 447... | WF58.50-P-3530-07P | |
| Chisel for securing collar nut on joint flange | MODEL 124, 129, 140, 170, 171, 199, 201, 202, 203, 208, 209, 210, 211, 215, 219, 220, 230, 231, 639... | WF58.50-P-3531-01A | |
| Pressing bush for wrench socket | MODEL 129, 140, 170, 171, 202, 203, 208, 210, 220 Rear axle differential 198 | WF58.50-P-3531-02A | |
| Pressing-in bush for wrench socket | MODEL 210... | WF58.50-P-3531-02B | |
| Assembly sleeve for tapered roller bearing inner race of drive pinion | MODEL 129, 140, 170, 171, 202, 203, 208, 209, 210, 211, 219, 220, 230... | WF58.50-P-3531-03A | |
| Press on sleeve for tapered roller bearing cone on drive pinion | MODEL 124, 129, 140, 170, 201, 202, 203, 208, 209, 210, 211... | WF58.50-P-3531-03B | |
| Produce press-on sleeve for ABS gear on drive pinion in accordance with drawing. | MODEL 124, 129, 140, 170, 201, 202, 208... | WF58.50-P-3531-04B | |
| Lever for pressing the spring clamp lever for poly-V-belt tensioning device | MODEL 124 with ENGINES 605, 606 MODEL 202 with ENGINES 604, 605 MODEL 408 with ENGINE 602 | WF58.50-P-3902-01A | |
| Support for retaining device | MODEL all | WF58.50-P-4020-01A | |
| Test mandrel for rear-axle wheel control | MODEL 129, 140, 170, 171, 202, 203, 208, 209, 210, 215, 220 | WF58.50-P-4030-01A | |
| Plug gauge for steering idler arm bearing bracket | MODEL 140 | WF58.50-P-4030-02A | |
| Drift for releasing the fitting sleeves in the flexible couplings | Model all (CAR, Light transporter) | WF58.50-P-4110-01A | |
| Wiring harness for actuation of switchover valve | MODEL 129.076, 140.04/05/06/07 | WF58.50-P-4210-01A | |
| Device for withdrawing roll pins on front wheel hub | MODEL 140.### #A as of 000001 up to 167053 up to 3.9.93 | WF58.50-P-4210-02A | |
| Tool for unlocking the parking brake control cable | MODEL 129, 140, 163, 202, 203, 209, 210, 211, 215, 219, 220, 230, 240 | WF58.50-P-4220-01A | |
| Insertion device for spacer for brake line | Model 205 | WF58.50-P-4250-01A | |
| Measurement connection for checking non-return valve or brake booster | MODEL 129, 140, 202, 460, 461, 463, 638 | WF58.50-P-4310-01A | |
| Hook for aligning inner panel | MODEL 203.0 | WF58.50-P-4340-01P | |
| U-bolt for assembling protective sleeve on steering lock | MODEL 129, 140, 210 | WF58.50-P-4610-01A | |
| Steering wheel hub for clamping upper steering shaft | MODEL 171, 210, 215, 220, 230... | WF58.50-P-4610-02I | |
| Insertion tool for mounting screw of lower steering damper | MODEL 215, 220 | WF58.50-P-4620-01A | |
| Connection piece for draining fuel tank | MODEL 203, 209... | WF58.50-P-4710-01A | |
| Adapter cable for electromagnetic clutch at compressor | MODEL 202 with ENGINE 111.944/975 | WF58.50-P-4781-01A | |
| Template for calibration of reversing camera | MODEL 164, 207, 212, 216, 218, 221, 251... | WF58.50-P-5465-01EL | |
| Modify locating tool for fastening front axle carrier | MODEL 169, 245 | WF58.50-P-6200-01AK | |
| Copper plate for welding in metal parts | MODEL all | WF58.50-N-6310-01A | |
| Beading pliers for areas difficult to access | MODEL 211.0, 209.3 | WF58.50-P-6350-01T | |
| Crimping pliers for areas not easily accessible | MODEL 219, 221 | WF58.50-P-6350-01Y | |
| Sheet metal crimping pliers for areas not easily accessible | MODEL 166, 204, 207, 212, 216, 218 | WF58.50-P-6350-01SC | |
| Fabricate drilling template for taillamp mounts | MODEL 199 | WF58.50-P-6420-03A | |
| Angular plate for removing garage door opener | MODEL 170 | WF58.50-P-6805-01A | |
| Cover panel for protecting roof paneling | MODEL 215.375/378 | WF58.50-P-6805-05N | |
| Installer for lock cylinder, driver lug | MODEL 170, 202 | WF58.50-P-6810-01A | |
| Removal tool for lock cylinder | MODEL 203, 230 | WF58.50-P-6810-02A | |
| Hook for unlocking glove compartment lid | MODEL 220 | WF58.50-P-6810-04A | |
| Tool for removing catch of single-part cover on center console | MODEL 140 | WF58.50-P-6820-01A | |
| Saw template for seat-belt guide bracket opening in roof frame's trim | MODEL 210.2 | WF58.50-P-6830-01FA | |
| Fabricate template for installing handles in headliner | MODEL 163.113/136/154/172 up to 31.8.01 with CODE (847) 3rd seat row | WF58.50-P-6830-02GH | |
| Fabricate template for installing speakers in C-pillar trim | Model 156, 176, 242, 246 with code 810 (Premium sound system) | WF58.50-P-6830-03A | |
| Centering aid for bore in cord | MODEL 220.175/176/178 with CODE Z07 (Top protection) | WF58.50-P-6850-02MB | |
| Roof handle removal tool | MODEL 203, 209.3 | WF58.50-P-6870-03A | |
| Modify locking bolt | Engine 654, 656 | WF58.50-P-7000-01OLM | |
| U section for protecting door frame | MODEL 211.065/070 with CODE (Z04) Light armoring | WF58.50-P-7210-01TG | |
| Auxiliary scale for checking hydraulic power window assembly oil level | Model 222.176/182/185/976/980 with code Z07 (B7 armoring on special protection version) | WF58.50-P-7211-01A | |
| Piece of hard wood for supporting rear door window | MODEL 220.1/8 with CODE (Z07) Top protection | WF58.50-P-7212-01MB | |
| Reinforcement for center door | MODEL 220.8 with CODE (Z07) Top protection | WF58.50-P-7214-01MB | |
| Centering bolts for sliding roof | MODEL 124, 463 | WF58.50-P-7720-01A | |
| Modifying installation pliers (special tool) for sliding/pop-up roof | MODEL 210 with CODE (414a) Glass electric tilting/sliding roof | WF58.50-P-7720-02A | |
| Puller hook for lower part of clip on sliding/pop-up roof trim | MODEL all | WF58.50-P-7720-03A | |
| Hook for removal of roller sun blind for lamella roof | MODEL 169.0/3 with CODE (417) Louver sunroof | WF58.50-P-7720-05AK | |
| Safety hook for tensioning roller sun blind for lamella roof | MODEL 169.0/3, 245.2 with CODE (417) Lamella roof | WF58.50-P-7720-06AK | |
| Safety hook for tensioning roller sun blind for panoramic roof | MODEL 245.2 with CODE (416) Fixed panoramic glass roof | WF58.50-P-7721-02BK | |
| Wiring harness for emergency operation of side flaps | MODEL 230.4 | WF58.50-P-7730-01R | |
| Wiring harness for emergency actuation of rear shelf | MODEL 171.4, 172.4, 231 | WF58.50-P-7730-02W | |
| Additionally seal injection nozzle for seal on Vario roof at front side | MODEL 230.4 except CODE (P99) Special model "AMG Black Series" | WF58.50-P-7750-01R | |
| Release lever for removing center high-mounted stop lamp | MODEL 210.2 as of 1.6.99 with CODE (340a) Additional 3rd stop lamp | WF58.50-P-8210-01A | |
| Unlocking tool for CD compartment/cassette compartment | MODEL 203, 209 with CODE (819a) CD changer | WF58.50-P-8264-02P | |
| Rod for opening the reed valve in the air/water duct | MODEL 164, 215, 216, 220, 221, 240, 251 | WF58.50-P-8310-01A | |
| Screwdriver bit for actuator motor | MODEL all | WF58.50-P-8320-01A | |
| Torx double end box wrench for removal of refrigerant compressor | MODEL 220 with ENGINE 112, 113 MODEL 221 with ENGINE 642 | WF58.50-P-8355-01A | |
| Drilling template for license plate adapter plate | MODEL 230.4 with CODE (P99) Special model "AMG Black Series" | WF58.50-P-8850-02A | |
| Assembly hook for tacking tool | MODEL 202, 220, 215 | WF58.50-P-9118-01A | |
| Installation tool for retaining wire | MODEL 210, 211, 215, 219, 220, 240 | WF58.50-P-9118-02A | |
| Assembly lever for tool for snapping off attachment of front seat belt guide fitting | MODEL 208.4 | WF58.50-P-9140-01KA | |
| Lever for pressing down the gas-operated strut on the support element of the roll bar | MODEL 230 except CODE (P99) Special model "AMG Black Series" | WF58.50-P-9150-01R | |
| Adapter cable for firing airbag and ETR units | MODEL 202 | WF58.50-P-9160-01A | |
| Ignition cable for firing airbag and seat belt tensioner units | MODEL 163, 164, 168, 170, 199, 202, 203, 208, 209, 210, 215, 220, 230, 240, 251, 414, 415, 420, 447, 448, 461, 463, 636, 639, 900, 901, 902, 903, 904, 905, 906, 909... | WF58.50-P-9160-02A | |
| Cover panel for protecting rubber seal beneath drip molding | MODEL 126 | WF58.50-P-9800-01A |