Cylinder Head/Cylinder Head Bolts - BE01.30-P-1000-04B
WARNING: This page does not describe the selected car, but rather 12 other vehicles, including the 2023 Mercedes-Benz CLA45 AMG, 2023 Mercedes-Benz CLA35 AMG, 2023 Mercedes-Benz CLA250, 2022 Mercedes-Benz CLA45 AMG, and 2022 Mercedes-Benz CLA35 AMG. However, it is still accessible from the selected car via links, so may be relevant.
Engine 103, 104, 111, 112, 113, 119, 120, 137, 155, 157, 256, 260, 270, 271, 272, 273, 274, 275, 276.9, 277, 278, 279, 285
CYLINDER HEAD/CYLINDER HEAD BOLTS
| Number | Designation | Engine 103 | Engine 104 | ||
|---|---|---|---|---|---|
| BE01.30-P-1001-04B | Cylinder head bolt | Thread diameter | M | 12 | 12 |
| Length (L) when new | mm | 105 | 160 | ||
| Length (L) | mm | ≤108, 4 | ≤162, 7 | ||
| - | - | - | |||
| BE01.30-P-1002-04B | Cylinder head | Overall height "H" mm | mm | 89, 9...90, 0 | 135, 9...136, 0 |
| Height | mm | ≤89, 5 | ≤135, 5 | ||
| - | - | - | |||
| BE01.30-P-1003-04B | Cylinder head | Permissible difference of flatness of contact surface in a longitudinal direction | mm | - | - |
| Permissible difference of flatness of contact surface in a transverse direction | mm | - | - | ||
| Peak-to-valley height | μm | - | - | ||
| BE01.30-P-1004-04B | Cylinder head when new | Reference dimension "H1" | mm | - | - |
| Reference dimension "H2" | mm | - | - | ||
| BE01.30-P-1005-04B | Cylinder head after necessary stock removal | Reference dimension "H1" | mm | - | - |
| Reference dimension "H2" | mm | - | - | ||
CYLINDER HEAD/CYLINDER HEAD BOLTS
| Number | Designation | Engine 111 | Engine 112 | ||
|---|---|---|---|---|---|
| BE01.30-P-1001-04B | Cylinder head bolt | Thread diameter | M | 12 | 11 |
| Length (L) when new | mm | 102 | 141, 5 | ||
| Length (L) | mm | ≤105 | ≤144, 5 | ||
| For picture, see | AR01.30-P-5800-03HA | AR01.30-P-5800-03B | |||
| BE01.30-P-1002-04B | Cylinder head | Overall height "H" mm | mm | 135, 9...136, 0 | 106, 2...106, 3 |
| Height | mm | ≤135, 5 | - | ||
| For picture, see | AR01.30-P-7162A | - | |||
| BE01.30-P-1003-04B | Cylinder head | Permissible difference of flatness of contact surface in a longitudinal direction | mm | 0, 08 | 0, 1 |
| Permissible difference of flatness of contact surface in a transverse direction | mm | 0 | 0, 1 | ||
| Peak-to-valley height | μm | 3/10 | 10 | ||
| BE01.30-P-1004-04B | Cylinder head when new | Reference dimension "H1" | mm | - | - |
| Reference dimension "H2" | mm | - | - | ||
| BE01.30-P-1005-04B | Cylinder head after necessary stock removal | Reference dimension "H1" | mm | - | - |
| Reference dimension "H2" | mm | - | - | ||
CYLINDER HEAD/CYLINDER HEAD BOLTS
| Number | Designation | Engine 113 | Engine 119 | ||
|---|---|---|---|---|---|
| BE01.30-P-1001-04B | Cylinder head bolt | Thread diameter | M | 11 | 12 |
| Length (L) when new | mm | 141, 5 | 160 | ||
| Length (L) | mm | ≤144, 5 | ≤162, 7 | ||
| For picture, see | AR01.30-P-5800-03B | - | |||
| BE01.30-P-1002-04B | Cylinder head | Overall height "H" mm | mm | - | - |
| Height | mm | - | - | ||
| - | - | - | |||
| BE01.30-P-1003-04B | Cylinder head | Permissible difference of flatness of contact surface in a longitudinal direction | mm | - | - |
| Permissible difference of flatness of contact surface in a transverse direction | mm | - | - | ||
| Peak-to-valley height | μm | - | - | ||
| BE01.30-P-1004-04B | Cylinder head when new | Reference dimension "H1" | mm | - | 130, 6..130, 7 |
| Reference dimension "H2" | mm | - | 145, 9..146, 0 | ||
| BE01.30-P-1005-04B | Cylinder head after necessary stock removal | Reference dimension "H1" | mm | - | 130, 0 |
| Reference dimension "H2" | mm | - | 145, 3 | ||
CYLINDER HEAD/CYLINDER HEAD BOLTS
| Number | Designation | Engine 120 | Engine 137 | ||
|---|---|---|---|---|---|
| BE01.30-P-1001-04B | Cylinder head bolt | Thread diameter | M | 12 | 10 |
| Length (L) when new | mm | 168 | 126/162 | ||
| Length (L) | mm | ≤171 | ≤129/165 | ||
| For picture, see | - | AR01.30-P-5800-03L | |||
| BE01.30-P-1002-04B | Cylinder head | Overall height "H" mm | mm | 135, 9...136, 0 | - |
| Height | mm | 2135, 5 | - | ||
| - | - | - | |||
| BE01.30-P-1003-04B | Cylinder head | Permissible difference of flatness of contact surface in a longitudinal direction | mm | 0, 03 | |
| Permissible difference of flatness of contact surface in a transverse direction | mm | 0, 03 | |||
| Peak-to-valley height | μm | - | 10 | ||
| BE01.30-P-1004-04B | Cylinder head when new | Reference dimension "H1" | mm | - | - |
| Reference dimension "H2" | mm | - | - | ||
| BE01.30-P-1005-04B | Cylinder head after necessary stock removal | Reference dimension "H1" | mm | - | 110, 87...110, 95 |
| Reference dimension "H2" | mm | - | - | ||
CYLINDER HEAD/CYLINDER HEAD BOLTS
| Number | Designation | Engine 155 | Engine 157, 278 | ||
|---|---|---|---|---|---|
| BE01.30-P-1001-04B | Cylinder head bolt | Thread diameter | M | 11 | 11 |
| Length (L) when new | mm | 175 ±0, 5 | 173 | ||
| Length (L) | mm | ≤176, 6 | ≤174, 5 | ||
| For picture, see | AR01.30-P-5800-03B | - | |||
| BE01.30-P-1002-04B | Cylinder head | Overall height "H" mm | mm | 114, 9...115, 1 | - |
| Height | mm | 114, 9...115, 1 | - | ||
| - | - | - | |||
| BE01.30-P-1003-04B | Cylinder head | Permissible difference of flatness of contact surface in a longitudinal direction | mm | ||
| Permissible difference of flatness of contact surface in a transverse direction | mm | ||||
| Peak-to-valley height | μm | - | - | ||
| BE01.30-P-1004-04B | Cylinder head when new | Reference dimension "H1" | mm | - | - |
| Reference dimension "H2" | mm | - | - | ||
| BE01.30-P-1005-04B | Cylinder head after necessary stock removal | Reference dimension "H1" | mm | - | - |
| Reference dimension "H2" | mm | - | - | ||
CYLINDER HEAD/CYLINDER HEAD BOLTS
| Number | Designation | Engine 256 | Engine 260 | ||
|---|---|---|---|---|---|
| BE01.30-P-1001-04B | Cylinder head bolt | Thread diameter | M | 11 | 11 |
| Length (L) when new | mm | 158 ±0, 5 | 163 | ||
| Length (L) | mm | ≤159, 5 | ≤164 | ||
| - | - | - | |||
| BE01.30-P-1002-04B | Cylinder head | Overall height "H" mm | mm | - | - |
| Height | mm | - | - | ||
| - | - | - | |||
| BE01.30-P-1003-04B | Cylinder head | Permissible difference of flatness of contact surface in a longitudinal direction | mm | - | - |
| Permissible difference of flatness of contact surface in a transverse direction | mm | - | - | ||
| Peak-to-valley height | μm | - | - | ||
| BE01.30-P-1004-04B | Cylinder head when new | Reference dimension "H1" | mm | - | - |
| Reference dimension "H2" | mm | - | - | ||
| BE01.30-P-1005-04B | Cylinder head after necessary stock removal | Reference dimension "H1" | mm | - | - |
| Reference dimension "H2" | mm | - | - | ||
CYLINDER HEAD/CYLINDER HEAD BOLTS
| Number | Designation | Engine 270 | Engine 271 | ||
|---|---|---|---|---|---|
| BE01.30-P-1001-04B | Cylinder head bolt | Thread diameter | M | 11 | 10x1, 5 |
| Length (L) when new | mm | 163 | 165 | ||
| Length (L) | mm | ≤164 | ≤167, 5 | ||
| - | - | - | |||
| BE01.30-P-1002-04B | Cylinder head | Overall height "H" mm | mm | - | 114, 9...115, 1 |
| Height | mm | - | 114, 9...115, 1 | ||
| - | - | - | |||
| BE01.30-P-1003-04B | Cylinder head | Permissible difference of flatness of contact surface in a longitudinal direction | mm | - | 0.07 |
| Permissible difference of flatness of contact surface in a transverse direction | mm | - | 0, 05 | ||
| Peak-to-valley height | μm | - | 10 | ||
| BE01.30-P-1004-04B | Cylinder head when new | Reference dimension "H1" | mm | - | - |
| Reference dimension "H2" | mm | - | - | ||
| BE01.30-P-1005-04B | Cylinder head after necessary stock removal | Reference dimension "H1" | mm | - | - |
| Reference dimension "H2" | mm | - | - | ||
CYLINDER HEAD/CYLINDER HEAD BOLTS
| Number | Designation | Engine 272 | Engine 273 | ||
|---|---|---|---|---|---|
| BE01.30-P-1001-04B | Cylinder head bolt | Thread diameter | M | 11 | 11 |
| Length (L) when new | mm | 170 | 170 | ||
| Length (L) | mm | ≤172 | ≤172 | ||
| - | - | - | |||
| BE01.30-P-1002-04B | Cylinder head | Overall height "H" mm | mm | - | - |
| Height | mm | - | - | ||
| - | - | - | |||
| BE01.30-P-1003-04B | Cylinder head | Permissible difference of flatness of contact surface in a longitudinal direction | mm | - | - |
| Permissible difference of flatness of contact surface in a transverse direction | mm | - | - | ||
| Peak-to-valley height | μm | - | - | ||
| BE01.30-P-1004-04B | Cylinder head when new | Reference dimension "H1" | mm | - | - |
| Reference dimension "H2" | mm | - | - | ||
| BE01.30-P-1005-04B | Cylinder head after necessary stock removal | Reference dimension "H1" | mm | - | - |
| Reference dimension "H2" | mm | - | - | ||
CYLINDER HEAD/CYLINDER HEAD BOLTS
| Number | Designation | Engine 274 | Engine 275, 285 | ||
|---|---|---|---|---|---|
| BE01.30-P-1001-04B | Cylinder head bolt | Thread diameter | M | 11 | 10 |
| Length (L) when new | mm | 163 | 132/168, 5 | ||
| Length (L) | mm | ≤164 | ≤133, 5/170 | ||
| - | - | - | |||
| BE01.30-P-1002-04B | Cylinder head | Overall height "H" mm | mm | - | - |
| Height | mm | - | - | ||
| - | - | - | |||
| BE01.30-P-1003-04B | Cylinder head | Permissible difference of flatness of contact surface in a longitudinal direction | mm | 0, 03 | |
| Permissible difference of flatness of contact surface in a transverse direction | mm | 0, 03 | |||
| Peak-to-valley height | μm | - | 10 | ||
| BE01.30-P-1004-04B | Cylinder head when new | Reference dimension "H1" | mm | - | - |
| Reference dimension "H2" | mm | - | - | ||
| BE01.30-P-1005-04B | Cylinder head after necessary stock removal | Reference dimension "H1" | mm | - | 110, 87...110, 95 |
| Reference dimension "H2" | mm | - | - | ||
CYLINDER HEAD/CYLINDER HEAD BOLTS
| Number | Designation | Engine 276.9 | Engine 277 | ||
|---|---|---|---|---|---|
| BE01.30-P-1001-04B | Cylinder head bolt | Thread diameter | M | 11 | 10 |
| Length (L) when new | mm | 170 | 168, 5 | ||
| Length (L) | mm | ≤172 | ≤170 | ||
| - | - | - | |||
| BE01.30-P-1002-04B | Cylinder head | Overall height "H" mm | mm | - | - |
| Height | mm | - | - | ||
| - | - | - | |||
| BE01.30-P-1003-04B | Cylinder head | Permissible difference of flatness of contact surface in a longitudinal direction | mm | ||
| Permissible difference of flatness of contact surface in a transverse direction | mm | ||||
| Peak-to-valley height | μm | - | - | ||
| BE01.30-P-1004-04B | Cylinder head when new | Reference dimension "H1" | mm | - | - |
| Reference dimension "H2" | mm | - | - | ||
| BE01.30-P-1005-04B | Cylinder head after necessary stock removal | Reference dimension "H1" | mm | - | - |
| Reference dimension "H2" | mm | - | - | ||
CYLINDER HEAD/CYLINDER HEAD BOLTS
| Number | Designation | Engine 279 | ||
|---|---|---|---|---|
| BE01.30-P-1001-04B | Cylinder head bolt | Thread diameter | M | 10 |
| Length (L) when new | mm | 168, 5 | ||
| Length (L) | mm | ≤170 | ||
| - | - | |||
| BE01.30-P-1002-04B | Cylinder head | Overall height "H" mm | mm | - |
| Height | mm | - | ||
| - | - | |||
| BE01.30-P-1003-04B | Cylinder head | Permissible difference of flatness of contact surface in a longitudinal direction | mm | - |
| Permissible difference of flatness of contact surface in a transverse direction | mm | - | ||
| Peak-to-valley height | μm | - | ||
| BE01.30-P-1004-04B | Cylinder head when new | Reference dimension "H1" | mm | - |
| Reference dimension "H2" | mm | - | ||
| BE01.30-P-1005-04B | Cylinder head after necessary stock removal | Reference dimension "H1" | mm | - |
| Reference dimension "H2" | mm | - | ||