Remove/Install Climate Control Heat Exchanger - AR83.25-P-1100MFA
WARNING: This page does not describe the selected car, but rather 12 other vehicles, including the 2023 Mercedes-Benz CLA45 AMG, 2023 Mercedes-Benz CLA35 AMG, 2023 Mercedes-Benz CLA250, 2022 Mercedes-Benz CLA45 AMG, and 2022 Mercedes-Benz CLA35 AMG. However, it is still accessible from the selected car via links, so may be relevant.
Model 118, 177, 243, 247
Shown on model 177.0
Shown on model 177.0
| Risk of injury to skin and eyes suffering scalding from contact with hot coolantspray. Risk of poisoning from swallowing coolant. | Do not open cooling system unless coolant temperature is below 90°C. Open cap slowly and release the overpressure. Do not pour coolant into beverage containers. Wear protective gloves, protective clothing and safety glasses. |
AS20.00-Z-0001-01A | |
| Risk of injury caused by scraping or cutting body parts on sharp vehicle parts | Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. Deburr repair panels. |
AS00.00-Z-0017-01A | |
| Notice | Notes on coolant | Model 118, 177, 247 with engine 260, 282, 608, 654Model 118, 177, 247.7 with engine 139 Model 243 with engine 780.20 |
AH20.00-P-2080-01KOA |
| Notes on safety-relevant components | AH00.00-Z-0019-01A | ||
| Remove/install | |||
| 1 | Remove heat shield (2) for firewall. | Model 118, 177, 247 Model 118, 177, 247 with engine 654 |
AR49.10-P-0001MFF |
| Model 118, 177, 247 with engine 608 | AR49.10-P-0001MFE | ||
| Model 118, 177, 247 with engine 282 | AR49.10-P-0001MFD | ||
| Model 118, 177, 247 with engine 260 | AR49.10-P-0001MFC | ||
| Model 118, 177, 247.7 with engine 139 | AR49.10-P-0001MFG | ||
| 2 | Provide a suitable container to collect the coolant. | ||
| 3 | Release and disconnect coolant hoses (3), and seal exposed connections with suitable protective covers. | AR20.20-P-7441-01RQ | |
| Fig 2 | |||
| 4 | Remove crossmember under instrument panel. | Model 243 | AR68.10-P-1120EQA |
| Model 118, 177, 247 | AR68.10-P-1120MFA | ||
| 5 | Push floor covering in working area to one side. | ||
| 6 | Remove screw (5) and remove bracket (6). | ||
| 7 | Remove screw (7) and remove thrust piece (8). | ||
| 8 | Provide a suitable container to collect the coolant. | ||
| 9 | Remove heat exchanger (1) with piping from air conditioner housing (9). | ||
| 10 | Install in the reverse order. | ||
| Concluding tasks | |||
| 11 | Bleed engine cooling system, check for leak tightness and correct coolant level. | Model 243 with engine 780 | AR20.00-P-1151EQA |
| Model 118, 177, 247.7 with engine 139 | AR20.00-P-1010MFG | ||
| Model 118, 177, 247 with engine 260, 282 | AR20.00-P-1010MFD | ||
| Model 118, 177, 247 with engine 608, 654 | AR20.00-P-1010MFE | ||
| 12 | Check heating for proper operation. |