Remove/install seat belt - AR91.40-P-1030RK
MODEL 231
Shown on left belt
| Remove/install | |||
| Risk of injury caused by performing testing or repair work on airbag or emergency tensioning retractor units. | Store airbag unit with deployment face up, do not subject to temperatures above 100 °C. When working on these units, disconnect the power supply. | AS91.00-Z-0001-01A | |
| Risk of injury caused by release of spring in the automatic belt retractor. | Never disassemble automatic belt retractors. | AS91.00-Z-0002-01A | |
| Notes on performing repair, body work and welding on vehicles with airbags and ETR units | AH91.00-P-0002-01M | ||
| Information on preventing damage to electronic components due to electrostatic discharge | AH54.00-P-0001-01A | ||
| Assessment of airbag and emergency tensioning retractor units in accident vehicles | AH91.00-P-0006-01B | ||
| Legal requirements on handling and storing airbags and emergency tensioning retractor units | AH91.00-P-0004-01A | ||
| 1 | Remove rear side paneling | AR68.30-P-4780RK | |
| 2 | Move front seat forward and upward | ||
| 3 | Unclip backrest hinge cover (1) and remove | ||
| 4 | Remove belt end fitting (2) at seat | AR91.40-P-1030-02A | |
| 5 | Remove belt (3) from belt guide (4) | ||
| 6 | Remove screw/bolt (5) and remove belt guide bracket (6) | *BA91.40-P-1025-01A | |
| Risk of explosion caused by escaping oxyhydrogen gas. Risk of injury caused by caustic burns to eyes, skin and mucous membranes from battery electrolyte (contains diluted sulfuric acid) or metal spatter due to short circuit. Risk of burn injuries caused by short circuit. Risk of poisoning caused by swallowing battery electrolyte (contains diluted sulfuric acid) or absorption of lead over the skin or orifices | No fire, sparks, open flames or smoking. Wear acid-resistant gloves and clothing and safety glasses with side guards. Do not place any conductive objects on the battery and avoid any short circuit from battery positive to ground. Only fill liquid battery electrolyte (diluted sulfuric acid) into suitable and appropriately marked containers. |
AS54.10-Z-0001-01A | |
| 7 | Disconnect ground line for on-board electrical system battery (G1) | AR54.10-P-0003RK | |
| Notes on battery | AH54.10-P-0001-01A | ||
| Notes on AGM battery | AH54.10-P-0002-01A | ||
| 8 | Disconnect electrical connector (7) from left front reversible emergency tensioning retractor (A76) or right front reversible emergency tensioning retractor (A76/1) | ||
| 9 | Remove bolts (8) | *BA91.40-P-1024-01A | |
| 10 | Remove left front reversible emergency tensioning retractor (A76) or right front reversible emergency tensioning retractor (A76/1) | In the event of a replacement, the removed parts must be disposed of properly. |
|
| Notes on disposing of airbag and emergency tensioning retractor units | OS91.00-P-0001-01A | ||
| 11 | Install in the reverse order | ||
| 12 | Connect Star Diagnosis and check Supplemental Restraint System (SRS) | Only when replacing left front reversible emergency tensioning retractor (A76) or right front reversible emergency tensioning retractor (A76/1). | AD00.00-P-2000-04A |
SEAT BELTS/EMERGENCY TENSIONING RETRACTORS
| Number | Designation | Model 231 | |
|---|---|---|---|
| BA91.40-P-1024-01A | Screw, automatic belt retractor to B-pillar | Nm | 35 |
| BA91.40-P-1025-01A | Screw/bolt, belt guide bracket to roof main bearing | Nm | 35 |