Press In Pilot Bushing - AR41.10-P-0250-03LF
Model 217
Model 222
MODIFICATION NOTES
| 20.04.2017 | Press-in dimension "a" from face end of pilot bushing to joint flange | Model 217.384/385/386 | BE41.10-P-1001-04B |
CHECK VALUES FOR PILOT BUSHING ON PROPELLER SHAFT
| Number | Designation | Model 217.364 | Model 217.377/378/477/478 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-04B | Press-in dimension "a" from face end of pilot bushing to joint flange | Front propeller shaft | mm | 23, 3 | 28, 8 |
| Rear propeller shaft | mm | 26, 8 | 36, 2 | ||
CHECK VALUES FOR PILOT BUSHING ON PROPELLER SHAFT
| Number | Designation | Model 217.379/479 | Model 217.382/383/482/483 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-04B | Press-in dimension "a" from face end of pilot bushing to joint flange | Front propeller shaft | mm | 25, 3 | 25, 3 |
| Rear propeller shaft | mm | 28, 8 | 36, 2 | ||
CHECK VALUES FOR PILOT BUSHING ON PROPELLER SHAFT
| Number | Designation | Model 217.384/385/386 | Model 222.004/020/021/032/034/035/082/083/121/123/132/135/179/182/183/982/983 Model 222.176 except code Z07 (Top protection) | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-04B | Press-in dimension "a" from face end of pilot bushing to joint flange | Front propeller shaft | mm | 24, 8 | 25, 3 |
| Rear propeller shaft | mm | 28, 3 | 28, 8 | ||
CHECK VALUES FOR PILOT BUSHING ON PROPELLER SHAFT
| Number | Designation | Model 222.033/057/085/086/133/157/184/185/186/984/985/986 | Model 222.067/167 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-04B | Press-in dimension "a" from face end of pilot bushing to joint flange | Front propeller shaft | mm | 24, 8 | 23, 3 |
| Rear propeller shaft | mm | 28, 3 | 36, 8 | ||
CHECK VALUES FOR PILOT BUSHING ON PROPELLER SHAFT
| Number | Designation | Model 222.077/177/178 | Model 222.104/120/134/976 Model 222.176 with code Z07 (Top protection) | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-04B | Press-in dimension "a" from face end of pilot bushing to joint flange | Front propeller shaft | mm | 28, 8 | 25, 3 |
| Rear propeller shaft | mm | 36, 2 | 36, 2 | ||
CHECK VALUES FOR PILOT BUSHING ON PROPELLER SHAFT
| Number | Designation | Model 222.162/165 | Model 222.163 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-04B | Press-in dimension "a" from face end of pilot bushing to joint flange | Front propeller shaft | mm | 36, 3 | 36, 2 |
| Rear propeller shaft | mm | 28, 3 | 36, 2 | ||
CHECK VALUES FOR PILOT BUSHING ON PROPELLER SHAFT
| Number | Designation | Model 222.967 | ||
|---|---|---|---|---|
| BE41.10-P-1001-04B | Press-in dimension "a" from face end of pilot bushing to joint flange | Front propeller shaft | mm | 23, 3 |
| Rear propeller shaft | mm | 34, 8 | ||
- Press in new pilot bushing using a suitable drift. Model 217, model 222
Observe the pressing-in dimension (a) from the front of the pilot bushing to the flange. The specified press-in distance (a) may deviate depending on the thickness of the flexible couplings, e.g. in vehicles with vibration damper. In these cases the dimension (a) measured prior to removal should be used for installation.