LEMON Manuals: Even more car manuals for everyone
Home >> Mercedes Benz >> 2018 >> GLS63 AMG >> Repair and Diagnosis >> Suspension >> Wheels & Tire System >> Wheels, Chassis Alignment Check - 166 Chassis 2 Of 2 >> Testing & Repair >> Check Vehicle Level At Front And Rear Axle With Electronic Inclinometer, Adjust If Necessary - AR40.20-P-0301GQ

Check Vehicle Level At Front And Rear Axle With Electronic Inclinometer, Adjust If Necessary - AR40.20-P-0301GQ

Model 166, 292 

MODIFICATION NOTES

20.10.2020 Assign specified suspension data on-line. Operation step 1.
G14136456Courtesy of MERCEDES-BENZ USA

Shown at measuring point 1 

G14136457Courtesy of MERCEDES-BENZ USA

Shown measuring point 3 

G14136458Courtesy of MERCEDES-BENZ USA
  Assign specified suspension data     
1 Assign specified suspension data on-line.   AR40.20-P-0001A
    IMPORTANT To make it easier to assign the current suspension data, the specified suspension data can be assigned on-line using the vehicle identification number.  
INSPECT Check     
2 Carry out preconditions and tests for vehicle level measurement.   AR40.20-P-0260SX
3 Clean measuring points (arrows). IMPORTANT This prevents any measuring errors.  
4 Position measuring sensor (086a) on lower control arm at front left (17). NOTES The connecting cable (086b) of measuring sensor (086a) must point to vehicle center. Otherwise the measurement will be inaccurate.
IMPORTANT The measurement sensor (086a) must be positioned exactly at the measuring points (arrows).		  
5 Measure vehicle level at measuring point 1 of left front lower control arm (17) using inclinometer (086) and store measured values. Vehicle level at front axle *BE40.20-P-1001-02T 
6 Repeat operation steps 4 and 5 at measuring point 2 of right front lower control arm. Vehicle level at front axle *BE40.20-P-1001-02T 
7 Position measuring sensor (086a) on lower control arm at rear left (27). NOTES The connecting cable (086b) of measuring sensor (086a) must point to vehicle center. Otherwise the measurement will be inaccurate.
IMPORTANT The measurement sensor (086a) must be positioned exactly at the measuring points (arrows).		  
8 Measure vehicle level at measuring point 3 of lower control arm at rear left (27) using inclinometer (086) and store measured values. Vehicle level at rear axle *BE40.20-P-1001-03U 
9 Repeat operation steps 7 and 8 at measuring point 4 of right rear lower control arm. Vehicle level at rear axle *BE40.20-P-1001-03U 
10 Check maximum permissible difference in vehicle level between left and right side of vehicle. IMPORTANT The specified test tolerance applies only when checking the vehicle level but not for calibration.  
    Permissible difference in vehicle level at front axle between right and left sides of the vehicle *BE40.20-P-1002-02T 
    Permissible difference in vehicle level at rear axle between right and left sides of vehicle *BE40.20-P-1002-03U 
11 Remove front axle spring. Model 166, 292 except code 489 (AIRMATIC)
If adjustment operations on the front axle are required.		  
      AR32.20-P-0200GQ
12 Remove rear axle spring. Model 166, 292 except code 489 (AIRMATIC)
If adjustment operations on the rear axle are required.		  
      AR32.20-P-0230GZ
13.1 Adjust vehicle level. If adjustment operations are required.  
    Model 166, 292 except code 489 (AIRMATIC) AR40.20-P-0301-02GQ
    Vehicle level at front axle *BE40.20-P-1001-02T 
    Vehicle level at rear axle *BE40.20-P-1001-03U 
    Vehicle level adaptation *BE40.20-P-1001-11C 
    Vehicle level adaptation *BE40.20-P-1001-12B 
    Permissible difference in vehicle level at front axle between right and left sides of the vehicle *BE40.20-P-1002-02T 
    Permissible difference in vehicle level at rear axle between right and left sides of vehicle *BE40.20-P-1002-03U 
13.2 Calibrate vehicle level using vehicle diagnosis system. Model 166, 292 with code 489 (AIRMATIC)
If adjustment operations are required.		  
REFER TO SELF-DIAGNOSTIC SYSTEMS     AD00.00-P-2000-04A
    IMPORTANT The calibration values may differ from the actual specified value.  
    Vehicle level at rear axle *BE40.20-P-1001-03U 
    Vehicle level at front axle
If the vehicle level is not OK after calibration,
↓
check level sensor and mounting of level sensor.		 *BE40.20-P-1001-02T 
14 Check headlamp adjustment and correct if necessary. Only if the vehicle level was adjusted.  
REFER TO MAINTENANCE   Model 166 as of model year 2016
Model 292		 AP82.10-P-8260I
REFER TO MAINTENANCE   Model 166 up to model year 2016 AP82.10-P-8260GZA
TEST AND ADJUSTMENT VALUES FOR VEHICLE LEVEL AT FRONT AXLE

Number Designation   Model 166.0 except code 489/491/Z04/Z05 Model 166.0 with code 489, model 166.8
BE40.20-P-1001-02T Vehicle level at front axle ∠° 9, 07 (±1, 2) 5, 26 (±1, 2)
TEST AND ADJUSTMENT VALUES FOR VEHICLE LEVEL AT FRONT AXLE

Number Designation   Model 166.0 with code 491 Model 166.0 with code Z04/Z05
BE40.20-P-1001-02T Vehicle level at front axle ∠° 7, 97 (±1, 2) 5, 26 (±1, 2)
TEST AND ADJUSTMENT VALUES FOR VEHICLE LEVEL AT FRONT AXLE

Number Designation   Model 166 AMG Model 292 except code 489
BE40.20-P-1001-02T Vehicle level at front axle ∠° 5, 26 (±1, 2) 6, 49 (±1, 2)
TEST AND ADJUSTMENT VALUES FOR VEHICLE LEVEL AT FRONT AXLE

Number Designation   Model 292 with code 489 Model 292 AMG
BE40.20-P-1001-02T Vehicle level at front axle ∠° 5, 26 (±1, 2) 5, 26 (±1, 2)
TEST AND ADJUSTMENT VALUES FOR VEHICLE LEVEL AT REAR AXLE

Number Designation   Model 166.0 except code 489/491/Z04/Z05 Model 166.0 with code 489, model 166.8
BE40.20-P-1001-03U Vehicle level at rear axle ∠° 3, 36 (±1, 1) -0, 77 (±1, 1)
TEST AND ADJUSTMENT VALUES FOR VEHICLE LEVEL AT REAR AXLE

Number Designation   Model 166.0 with code 491 Model 166.0 with code Z04/Z05
BE40.20-P-1001-03U Vehicle level at rear axle ∠° 2, 39 (±1, 1) -0, 77 (±1, 1)
TEST AND ADJUSTMENT VALUES FOR VEHICLE LEVEL AT REAR AXLE

Number Designation   Model 166 AMG Model 292 except code 489
BE40.20-P-1001-03U Vehicle level at rear axle ∠° -0, 77 (±1, 1) -0, 64 (±1, 1)
TEST AND ADJUSTMENT VALUES FOR VEHICLE LEVEL AT REAR AXLE

Number Designation   Model 292 with code 489 Model 292 AMG
BE40.20-P-1001-03U Vehicle level at rear axle ∠° -0, 77 (±1, 1) -0, 77 (±1, 1)
FRONT AXLE ALIGNMENT

Number Designation       Model 166 Model 292
BE40.20-P-1001-11C Vehicle level adaptation Shim 1 Thickness mm 1, 50 1, 50
      Adaptation (height) mm 2, 54 2, 54
      Adaptation (Romess) ∠° 0, 31 0, 31
    Shim 2 Thickness mm 2, 00 2, 00
      Adaptation (height) mm 3, 38 3, 38
      Adaptation (Romess) ∠° 0, 42 0, 42
    Shim 3 Thickness mm 5, 00 5, 00
      Adaptation (height) mm 8, 45 8, 45
      Adaptation (Romess) ∠° 1, 03 1, 03
    Shim 4 Thickness mm 10, 00 10, 00
      Adaptation (height) mm 16, 90 16, 90
      Adaptation (Romess) ∠° 2, 06 2, 06
REAR AXLE ALIGNMENT

Number Designation       Model 166 Model 292
BE40.20-P-1001-12B Vehicle level adaptation Shim 1 Thickness mm 1, 50 1, 50
      Adaptation (height) mm 2, 91 2, 91
      Adaptation (Romess) ∠° 0, 34 0, 34
    Shim 2 Thickness mm 2, 00 2, 00
      Adaptation (height) mm 3, 88 3, 88
      Adaptation (Romess) ∠° 0, 45 0, 45
    Shim 3 Thickness mm 5, 00 5, 00
      Adaptation (height) mm 9, 70 9, 70
      Adaptation (Romess) ∠° 1, 13 1, 13
    Shim 4 Thickness mm 10, 00 10, 00
      Adaptation (height) mm 19, 40 19, 40
      Adaptation (Romess) ∠° 2, 26 2, 26
TEST AND ADJUSTMENT VALUES FOR VEHICLE LEVEL AT FRONT AXLE

Number Designation   Model 166.0 except code 489/491/Z04/Z05 Model 166.0 with code 489, model 166.8
BE40.20-P-1002-02T Permissible difference in vehicle level When checking at front axle between right and left sides of the vehicle ∠° 0, 6 0, 6
TEST AND ADJUSTMENT VALUES FOR VEHICLE LEVEL AT FRONT AXLE

Number Designation   Model 166.0 with code 491 Model 166.0 with code Z04/Z05
BE40.20-P-1002-02T Permissible difference in vehicle level When checking at front axle between right and left sides of the vehicle ∠° 0, 6 0, 6
TEST AND ADJUSTMENT VALUES FOR VEHICLE LEVEL AT FRONT AXLE

Number Designation   Model 166 AMG Model 292 except code 489
BE40.20-P-1002-02T Permissible difference in vehicle level When checking at front axle between right and left sides of the vehicle ∠° 0, 6 0, 6
TEST AND ADJUSTMENT VALUES FOR VEHICLE LEVEL AT FRONT AXLE

Number Designation   Model 292 with code 489 Model 292 AMG
BE40.20-P-1002-02T Permissible difference in vehicle level When checking at front axle between right and left sides of the vehicle ∠° 0, 6 0, 6
TEST AND ADJUSTMENT VALUES FOR VEHICLE LEVEL AT REAR AXLE

Number Designation   Model 166.0 except code 489/491/Z04/Z05 Model 166.0 with code 489, model 166.8
BE40.20-P-1002-03U Permissible difference in vehicle level When checking at rear axle between right and left sides of vehicle ∠° 0, 5 0, 5
TEST AND ADJUSTMENT VALUES FOR VEHICLE LEVEL AT REAR AXLE

Number Designation   Model 166.0 with code 491 Model 166.0 with code Z04/Z05
BE40.20-P-1002-03U Permissible difference in vehicle level When checking at rear axle between right and left sides of vehicle ∠° 0, 5 0, 5
TEST AND ADJUSTMENT VALUES FOR VEHICLE LEVEL AT REAR AXLE

Number Designation   Model 166 AMG Model 292 except code 489
BE40.20-P-1002-03U Permissible difference in vehicle level When checking at rear axle between right and left sides of vehicle ∠° 0, 5 0, 5
TEST AND ADJUSTMENT VALUES FOR VEHICLE LEVEL AT REAR AXLE

Number Designation   Model 292 with code 489 Model 292 AMG
BE40.20-P-1002-03U Permissible difference in vehicle level When checking at rear axle between right and left sides of vehicle ∠° 0, 5 0, 5
scientia non olet · About LEMON Manuals