Remove/Install Complete Outside Mirror - AR88.70-P-9000LW

Model 205.0/1/2 

Model 213 

Model 253 

Model 293 

MODIFICATION NOTES 

Shown on left side of vehicle, model 205.0 

Courtesy of MERCEDES-BENZ USA

Shown on left side of vehicle, model 205.0 

Courtesy of MERCEDES-BENZ USA

	Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.	No parts of the body or limbs should be within the operating area when the components are moving.	AS00.00-Z-0011-01A
	Information on preventing damage to electronic components due to electrostatic discharge		AH54.00-P-0001-01A
	Remove/install
1	Move side window in front door to lower-most position.
2.1	Loosen door trim (1) until electrical connectors (3, 4) on front door control unit (12) are accessible.	Model 205.0/1/2, Model 213, Model 253, Model 293 except code 270 (Aerial for GPS) except code 274 (Telephone antenna) except code 501 (360° camera)	AR72.10-P-1000LW
2.2	Remove door trim (1) at front door.	Model 205.0/1/2, Model 213, Model 253, Model 293 with code 270 (Aerial for GPS) Model 205.0/1/2, Model 213, Model 253, Model 293 with code 274 (Telephone antenna) Model 205.0/1/2, Model 213, Model 253, Model 293 with code 501 (360° camera)	AR72.10-P-1000LW
3	Remove mirror triangle trim (2) on front door.	, Model 205.0/1/2 with code 810 (Sound system) Model 253, Model 293 with code 810 (Sound system) Allow mirror triangle paneling (2) to hang down with electrical line connected. , Model 213 Allow mirror triangle paneling (2) to hang down with electrical lines connected. The number of electrical connectors may vary depending on the equipment.
4	Disconnect electrical connectors (3, 4) from front door control unit (12).
5	Unclip electrical connector (5) from bracket and disconnect.	Model 205.0/1/2, Model 213, Model 253, Model 293 with code 501 (360° camera)
6	Unclip electrical connector (6) from bracket and disconnect.	Model 205.0/1/2, Model 213, Model 253, Model 293 with code 274 (Telephone antenna)
7	Unclip electrical connector (7) from bracket and disconnect.	Model 205.0/1/2, Model 213, Model 253, Model 293 with code 270 (Aerial for GPS)
8	Loosen window frame trim (13) in area of screws (9).	Model 213 The window frame paneling (13) is clipped into the window frame with a retaining clip in the area of the mirror triangle.
9	Lift seal (8) and remove screws (9).
10	Move top of outside mirror (11) out of door seal (10) and remove.
11	Install in the reverse order
12.1	Calibrate 360° camera in outside mirror (11) with diagnostic system.	Model 205.0/1/2, Model 213, Model 253, Model 293 with code 501 (360° camera) If the left or right outside mirror (11) has been removed.
		Model 293 with code 501 (360° camera)	AD00.00-P-2000-06FR
		Model 205.0/1/2, Model 213, Model 253 with code 501 (360° camera)	AD00.00-P-2000-04B
12.2	Calibrate all the cameras in the 360° camera system using the vehicle diagnosis system.	Model 205.0/1/2, Model 213, Model 253, Model 293 with code 501 (360° camera) If the left or right outside mirror (11) has been removed.
		Model 205.0/1/2, Model 213, Model 253 with code 501 (360° camera)	AD00.00-P-2000-04B
		Model 293 with code 501 (360° camera)	AD00.00-P-2000-06FR
	Check
13	Perform function test of outside mirror (11).