(Remove/Install Poly-V Belt - AR13.22-P-1202OLC)
Engine 654 in model 213, 238, 257
Shown on engine 654.9 in model 213
(except 213.011/016/211/216)
| Risk of injury caused by pinching or crushing when working on springs or spring bodies that are under tension | Use only approved tensioning devices; additionally screen off hazardous area if necessary. Check special tools for damage and proper operation (visual inspection). Wear protective gloves. | AS00.00-Z-0001-01A | |
| Risk of injury . Moving parts can pinch, crush or, in extreme cases even sever extremities. | No parts of the body or limbs should be within the operating area of mechanical components when moving components. | AS00.00-Z-0009-01A | |
| Risk of injury . Skin or eye injuries may result when handling hot or glowing objects. | Wear protective gloves, protective clothing and safety glasses, if necessary. | AS00.00-Z-0002-01A | |
| Remove/install | |||
| 1 | Remove upper engine cover (1). | AR01.10-P-2405OLC | |
| 2 | Remove engine air intake duct (2). | ||
| 3 | Remove impact plate (3). | ||
| 4 | Relieve clamping device (4) and fix with a 4 mm thick pin. | Engine 654.9 in model 213, 238, 257 | |
| 5 | Remove the poly-V-belt (5). | AR13.22-P-3902-02OLC | |
Do not use belt wax or similar products. The poly-V belt (5) will slip otherwise. |
|||
| Fig 1 | |||
| Check | |||
| 6 | Check poly-V-belt (5) for wear and damage. | ||
| AP13.22-P-1351-01A | |||
| If there is a problem, ↓ Replace the poly-V-belt (5). |
|||
| 7 | Check guide pulley (6) for wear and damage. | Engine 654.9 in model 213 (except 213.011/016/211/216) Engine 654.9 in model 238, 257 If there is a problem, ↓ Replace guide pulley (6). |
|
| AR13.20-P-0015OLC | |||
| 8 | Check clamping device (4) for wear and damage. | Engine 654.9 in model 213, 238, 257 | |
| If there is a problem, ↓ Replace clamping device (4). |
|||
| AR13.25-P-3220OLC | |||
| 9 | Check belt pulleys of alternator (G2) and refrigerant compressor for wear and damage. | Engine 654.9 in model 213 (except 213.011/016/211/216) Engine 654.9 in model 238, 257 If there is a problem, ↓ Replace alternator (G2) and/or refrigerant compressor. |
|
| Remove/install alternator Engine 654.9 in model 213 (except 213.011/016/211/216) Engine 654.9 in model 238, 257 |
AR15.40-P-5032OLC | ||
| Refrigerant compressor, remove/install Engine 654.9 in model 213 (except 213.011/016/211/216) |
AR83.55-P-5310LWE | ||
| Refrigerant compressor, remove/install Engine 654.9 in model 238, 257 |
AR83.55-P-5310LWM | ||
| 10 | Check belt pulley of coolant pump for wear and damage. | If there is a problem, ↓ Replace coolant pump. |
|
| AR20.10-P-1271OLC | |||
| 11 | Install in the reverse order. | ||
| Finishing activity | |||
| Risk of burn injuries , suffocation and poisoning when working on the exhaust system and the components connected to it Risk of suffocation and risk of poisoning caused by inhalation of gaseous and solid components of the exhaust. Risk of poisoning caused by skin contact with solid components of the exhaust | Wear protective clothing and safety glasses. Use the extraction system. Move people out of the hazard area. |
AS49.00-Z-0001-01A | |
| Risk of accident from vehicle starting off by itself when engine running Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running | Secure vehicle to prevent it from starting off by itself Wear closed and snug-fitting work clothes Do not touch hot or rotating parts | AS00.00-Z-0005-01A | |
| 12 | Perform engine test run While doing so check engine for proper operation and leak tightness |