Remove/install the suspension strut - AR32.25-P-1017NKB
MODEL 117, 156, 176, 242, 246
Shown on model 246
| Risk of injury due to fan starting unexpectedly | Do not reach into the rotation or hazard area of the fan. Wear closed and close-fitting work clothes. | AS20.40-Z-0001-01A | |
| Risk of injury . Moving parts can pinch, crush or, in extreme cases even sever extremities. | No parts of the body or limbs should be within the operating range of the mechanism when moving components. | AS00.00-Z-0009-01A | |
| Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. | AS00.00-Z-0010-01A | |
| Information on preventing damage to electronic components due to electrostatic discharge | AH54.00-P-0001-01A | ||
| Notes on self-locking nuts and bolts | AH00.00-N-0001-01A | ||
| Remove/install | |||
| Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof. | No parts of the body or limbs should be within the operating area when the components are moving. | AS00.00-Z-0011-01A | |
| 1 | Open engine hood and secure against falling down | ||
| 2 | Remove seal (10) | Model 242, 246 | |
| 3 | Remove left wiper arm (7) | Model 242, 246, 117 When removing the left suspension strut (1). |
|
| AR82.30-P-6100NKB | |||
| 4 | Remove right or left covering (8a or 8b) | Model 242, 246 | |
| 5 | Remove inner covering (9) | Model 242, 246 | |
| 6 | Detach front wheel and tire assembly | ||
| AP40.10-P-4050AK | |||
| 7 | Detach torsion bar linkage (4) from suspension strut (1) | *BA32.20-P-1003-02K | |
| 8 | Unscrew nuts (5) and pull bolts out of suspension strut (1) | *BA32.25-P-1003-04J | |
| 9 | Detach bracket (3) from suspension strut (1) | ||
| 10 | Press suspension strut (1) out of steering knuckle (2) | ||
| 11 | Secure suspension strut (1) against falling down | ||
| 12 | Detach electrical connection from suspension strut (1) | Model 117, 156, 176, 242, 246 with code 459 (Steel suspension with adjustable damping) |
|
| 13 | Unscrew bolts (6) and remove suspension strut (1) | Ensure that positioning shackles of the strut bearing do not come into contact with the suspension strut tower. Otherwise, the suspension strut tower will be damaged. |
|
| *BA32.25-P-1002-04J | |||
| Check | |||
| 14 | Check suspension strut (1) for damage | ||
| 15 | Install in the reverse order | ||
| 16 | Perform wheel alignment check | AR40.20-P-0200NKB |
FRONT AXLE TORSION BAR
| Number | Designation | Model 117 | Model 156 | |
|---|---|---|---|---|
| BA32.20-P-1003-02K | Self-locking nut, connecting rod to spring strut | Nm | 105 | 105 |
FRONT AXLE TORSION BAR
| Number | Designation | Model 242 | Model 176, 246 | |
|---|---|---|---|---|
| BA32.20-P-1003-02K | Self-locking nut, connecting rod to spring strut | Nm | 105 | 105 |
SUSPENSION STRUTS
| Number | Designation | Model 117, 176, 246 | Model 156 | ||
|---|---|---|---|---|---|
| BA32.25-P-1002-04J | Bolt, suspension strut to spring tower | Stage 1 | Nm | 50 | 50 |
| Stage 2 | ∠° | - | - | ||
SUSPENSION STRUTS
| Number | Designation | Model 242 | ||
|---|---|---|---|---|
| BA32.25-P-1002-04J | Bolt, suspension strut to spring tower | Stage 1 | Nm | 50 |
| Stage 2 | ∠° | - | ||
SUSPENSION STRUTS
| Number | Designation | Model 117, 176, 246 | Model 156 | ||
|---|---|---|---|---|---|
| BA32.25-P-1003-04J | Nut, suspension strut to steering knuckle | Stage 1 | Nm | 110 | 110 |
| Stage 2 | ∠° | 90 | 90 | ||
SUSPENSION STRUTS
| Number | Designation | Model 242 | ||
|---|---|---|---|---|
| BA32.25-P-1003-04J | Nut, suspension strut to steering knuckle | Stage 1 | Nm | 110 |
| Stage 2 | ∠° | 90 | ||