Disconnect/Connect Line Connection - AR32.00-P-0001-01A

Model 166, 292

with code 468 (ACTIVE CURVE SYSTEM)

HYDRAULIC PUMP

Number	Designation		Model 166 with engine 276	Model 166 with engine 642
BA32.00-P-1006-01A	Bolt, hydraulic line to hydraulic pump	Nm	10	10

HYDRAULIC PUMP

Number	Designation		Model 292 with engine 278
BA32.00-P-1006-01A	Bolt, hydraulic line to hydraulic pump	Nm	9

HYDRAULIC PUMP

Number	Designation		Model 166 with engine 157	Model 166 with engine 276
BA32.00-P-1007-01A	Bolt, mounting plate to distributor hydraulic line	Nm	8	8

HYDRAULIC PUMP

Number	Designation		Model 166 with engine 278	Model 166 with engine 642
BA32.00-P-1007-01A	Bolt, mounting plate to distributor hydraulic line	Nm	8	8

HYDRAULIC PUMP

Number	Designation		Model 292 with engine 278
BA32.00-P-1007-01A	Bolt, mounting plate to distributor hydraulic line	Nm	8

ACTIVE ROLL STABILIZATION

Number	Designation		Model 166	Model 292
BA32.34-P-1007-01A	Screw/bolt, oil line to rotary actuator on front axle/rear axle	Nm	20	20

ACTIVE ROLL STABILIZATION

Number	Designation		Model 166	Model 292
BA32.34-P-1008-01A	Screw/bolt, oil line to valve block on front axle/rear axle	Nm	20	20

Fig 1: Identifying Detaching Tool (230 589 01 33 00)

Courtesy of MERCEDES-BENZ USA

Fig 2: Identifying Record Plug (129 589 00 91 00)

Courtesy of MERCEDES-BENZ USA

Fig 3: Identifying Detaching Tool (221 589 01 33 00)

Courtesy of MERCEDES-BENZ USA

Disconnection of connection fittings

Clean connection fittings and surrounding area.
Mark connection fittings on line and component.
If more than one screwed-on line is detached.

With screwed-on connection fittings.
Unscrew screw/bolt (1) at threaded connection fitting and disconnect line.
With plugged-in connection fittings.
Disconnect plugged-in connection fittings using detaching tool or detaching tool.

With hose connections with clamp.

Detach clamp from hose connections and disconnect hose.

Courtesy of MERCEDES-BENZ USA

Collect escaping hydraulic fluid and seal connection fittings immediately using stop plugs.
Connection of connection fittings
Remove stop plugs from connection fittings.
1. With screwed-on connection fittings.
  With screwed-on and plugged-in connection fittings, check that O-ring is in good condition, undamaged and seated correctly; replace if necessary and apply hydraulic fluid.
2. With hose connections with clamp.
  With hose connections, check that hose and clamp are in good condition and undamaged; replace if necessary.

With screwed-on connection fittings.

With screwed-on connection fittings, insert connection fittings and tighten screw/bolt (1) with Model 166 with engine 276

with code 468 (ACTIVE CURVE SYSTEM)

Model 166 with engine 642

Courtesy of MERCEDES-BENZ USA

with code 468 (ACTIVE CURVE SYSTEM)

Model 292 with engine 278

with code 468 (ACTIVE CURVE SYSTEM)

, Model 166 with engine 157

with code 468 (ACTIVE CURVE SYSTEM)

Model 166 with engine 276

with code 468 (ACTIVE CURVE SYSTEM)

Model 166 with engine 278

with code 468 (ACTIVE CURVE SYSTEM)

Model 166 with engine 642

with code 468 (ACTIVE CURVE SYSTEM)

Model 292 with engine 278

with code 468 (ACTIVE CURVE SYSTEM)

, Model 166, 292

with code 468 (ACTIVE CURVE SYSTEM)

or Model 166, 292

with code 468 (ACTIVE CURVE SYSTEM) .

With plugged-in connection fittings.
With plugged-in connection fittings, insert connection fitting until it engages.
With hose connections with clamp.
With hose connections, attach hose and mount clamp.