Remove/Install Battery - AR54.10-P-0005GZ
MODEL 164, 166, 292
MODIFICATION NOTES
| 09.11.2016 | "Initial startup of battery" added | Operation step 18 |
Shown on model 164.1
| Risk of explosion from explosive gas. Risk of poisoning and caustic burns from swallowing battery electrolyte. Risk of injury through burns to skin and eyes from battery acid or when handling damaged lead-acid batteries | No fires, sparks, open flames or smoking. Wear acid-resistant gloves, clothing and glasses. Only pour battery acid into suitable and appropriately marked containers. |
AS54.10-Z-0001-01A | |
| Risk of injury caused by contact with battery gel when handling damaged lead-gelbatteries | No fires, sparks, open flames or smoking. Wear acid-resistant gloves, clothing and glasses. | AS54.10-Z-0001-02A | |
| Risk of injury caused by caustic burns to eyes, skin and mucous membranes from battery electrolyte or due to short circuit. Risk of burn injuries due to thermal changes. Risk of poisoning from swallowing battery electrolyte. | Wear protective gloves, protective clothing and safety glasses. In the event of escaping battery electrolyte, battery vapors, battery mist, smoke or heat development, secure the area, leave it and alert the fire department. | AS54.10-Z-0001-04A | |
| Notes on battery | AH54.10-P-0001-01A | ||
| Notes for 12-V lithium-ion battery | AH54.10-P-0004-01A | ||
| Information on preventing damage to electronic components due to electrostatic discharge | AH54.00-P-0001-01A | ||
| Notes on AGM battery | AH54.10-P-0002-01A | ||
| Remove/install | |||
| 1 | Move head restraint on front passenger seat (1) all the way down | Head restraint must be moved down to end stop. Otherwise the sun visor can be damaged when tilting the backrest forward. |
|
| 2 | Move front passenger seat (1) as far forward as possible and upwards, tilt seat backrest forward | ||
| 3 | Remove cover (2) | ||
| 4 | Separate floor covering (3) at both marked positions (arrows) | If the floor covering (3) was not separated already. | |
| 5 | Move front passenger seat (1) all the way to rear | Model 164, 166 | |
| 6 | Fold floor covering (3) forward | ||
| 7 | Move front passenger seat (1) far enough forward until the battery compartment is fully accessible | Model 164, 166 | |
| 8 | Switch off ignition and store transmitter key outside of transmission range (min. 2 m) | ||
| 9 | Remove expansion rivet (5) and remove air vent (4) | ||
| 10 | Remove battery cover (12) | ||
| 11 | Ensure that no jumper start device is connected to vehicle | ||
| 12 | Loosen nut on battery negative pole terminal (8) and disconnect ground line of battery (13) | AR54.10-P-0003GZ | |
| 13 | Remove positive battery terminal cover (6), undo nut on clamping device for positive battery terminal (7) and remove positive line | *BA54.10-P-1012-01C | |
| 14 | Detach vent hose (11) including plastic fitting from battery (13) | ||
| 15 | Unscrew nuts (10) and remove retaining plate (9) | Model 164, 292 |
*BA54.10-P-1024-01C |
| 16 | Remove battery (13) | Before the battery (13) is installed, it must be ensured that there are no cables in the battery support area. Otherwise they can be damaged when the battery (13) is installed. |
|
| 17 | Install in the reverse order | ||
| Initial startup | |||
| 18 | Confirm battery change in SAM control unit (N10) in the Actuations menu item | Model 166, 292 as of model year 2016 When replacing the battery (13). |
|
| AD00.00-P-2000-04A |
BATTERY
| Number | Designation | Model 164 | Model 166 | ||
|---|---|---|---|---|---|
| BA54.10-P-1012-01C | Nut, battery line to negative terminal/positive terminal | M6 | Nm | 6 | 6 |
BATTERY
| Number | Designation | Model 292 | ||
|---|---|---|---|---|
| BA54.10-P-1012-01C | Nut, battery line to negative terminal/positive terminal | M6 | Nm | 6 |
BATTERY
| Number | Designation | Model 164 | Model 292 | ||
|---|---|---|---|---|---|
| BA54.10-P-1024-01C | Nut, battery retaining plate to frame floor assembly | M8 | Nm | 24 | 24 |