Wiring Diagram For Adaptive Brake (ABR) - PE42.47-P-2000-97ZGB
Model 463 as of model year 2016 up to model year 2019 Control units N30/4, A7/3
| Code: | Designation: | Position: |
|---|---|---|
| A0 | Color code key | 48L |
| A7/3 | Traction system hydraulic unit | 3H |
| A7/3 | Traction system hydraulic unit | 3A |
| A7/3b1 | Front axle brake pressure sensor | 2B |
| A7/3b7 | Front pressure sensor | 4B |
| A7/3b8 | Rear pressure sensor | 2D |
| A7/3m1 | High pressure and return pump | 4D |
| A7/3y10 | Left rear pressure regulator valve (pressure hold) | 3F |
| A7/3y11 | Left rear pressure regulator valve (pressure release) | 4F |
| A7/3y12 | Right rear pressure regulator valve (pressure hold) | 3E |
| A7/3y13 | Right rear pressure regulator valve (pressure release) | 4E |
| A7/3y18 | Front axle switchover valve | 3E |
| A7/3y19 | Rear axle switchover valve | 4E |
| A7/3y22 | Front axle intake ball valve | 2D |
| A7/3y23 | Rear axle intake ball valve | 4D |
| A7/3y6 | Left front pressure regulator valve (pressure hold) | 3G |
| A7/3y7 | Left front pressure regulator valve (pressure release) | 4G |
| A7/3y8 | Right front pressure regulator valve (pressure hold) | 3F |
| A7/3y9 | Right front pressure regulator valve (pressure release) | 4F |
| B24/15 | Yaw rate, lateral and longitudinal acceleration sensor | 32L |
| B64/1 | Brake vacuum sensor | 42L |
| CAN E1 | Chassis CAN 1 | 39K |
| CAN H | Vehicle dynamics CAN | 33K |
| CAN H | Vehicle dynamics CAN | 36K |
| F32/3 | Engine compartment prefuse box | 6L |
| F32/3f161 | Fuse 161 | 5K |
| F58 | Front passenger footwell fuse and relay module | 11L |
| F58f209 | Fuse 209 | 9L |
| F58f211 | Fuse 211 | 10L |
| F58f224 | Fuse 224 | 11L |
| L6/1 | Left front axle rpm sensor | 24L |
| L6/2 | Right front axle rpm sensor | 26L |
| L6/3 | Left rear axle rpm sensor | 28L |
| L6/4 | Right rear axle rpm sensor | 29L |
| N10 | SAM control unit | 17L |
| N30/4 | Electronic Stability Program control unit | 12A |
| N30/4 | Electronic Stability Program control unit | 20A |
| N30/4 | Electronic Stability Program control unit | 28A |
| N30/4 | Electronic Stability Program control unit | 36A |
| N30/4 | Electronic Stability Program control unit | 43A |
| S11 | Brake fluid level switch | 19L |
| S9/1 | Stop lamp switch | 21L |
| W29/1 | A-pillar ground connection, left | 6E |
| X30/19 | Chassis CAN 1 (CAN E1) potential distributor electrical connector | 39L |
| X30/28 | Vehicle dynamics CAN (CAN H) potential distributor electrical connector | 36L |
| X92/3 | Vehicle frame electrical connector (22-pin) | 27E |