Press In Pilot Bushing - AR41.10-P-0250-03LW
Model 205, 213, 238, 253
CHECK VALUES FOR PILOT BUSHING ON PROPELLER SHAFT
| Number | Designation | Model 205 | ||||
|---|---|---|---|---|---|---|
| BE41.10-P-1001-04K | Press-in dimension "a" from face end of pilot bushing to joint flange | Four-arm flange | Hole circle Ø 120 | Front propeller shaft | mm | 25, 3 |
| Rear propeller shaft | mm | 28, 8 | ||||
| Three-arm flange | Hole circle Ø 110 | Front propeller shaft | mm | 24, 8 | ||
| Rear propeller shaft | mm | 28, 3 | ||||
| Hole circle Ø 100 | Front propeller shaft | mm | 23, 3 | |||
| Rear propeller shaft | mm | 26, 8 | ||||
CHECK VALUES FOR PILOT BUSHING ON PROPELLER SHAFT
| Number | Designation | Model 253.303/305/309/903/905/909 1 # except code 8U9, model 253.303/305/903/905 with code 8U9 except code 460/494/498/835, model 253.343/378, model 253.346/349 except code 494/835, model 253.943 except code 700, model 253.946/949 except code 494/700/835 | Model 253.177/178/180/18 1/184/354/364/377/9 42/964, model 253.303/305/903/90 5 2# except code 8U9, model 253.303/305/903/90 5 with code 460/494/498/835 + code 8U9 model 253.309/909 with code 8U9, model 253.346/349/946/94 9 with code 494/835, model 253.943/946/949 with code 700, model 253.954 except code 494/498 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-04N | Press-in dimension "a" from face end of pilot bushing to joint flange | Rear propeller shaft | mm | 34, 80 | 24, 50 |
CHECK VALUES FOR PILOT BUSHING ON PROPELLER SHAFT
| Number | Designation | Model 253.309/909 2# except code 8U9, model 253.325/925/948, model 253.954 with code 494/498 | ||
|---|---|---|---|---|
| BE41.10-P-1001-04N | Press-in dimension "a" from face end of pilot bushing to joint flange | Rear propeller shaft | mm | 26, 00 |
CHECK VALUES FOR PILOT BUSHING ON PROPELLER SHAFT
| Number | Designation | Model 213.004/013/064/148/183/204/213/264 Model 213.048 except code 700 (Technology Local Content China) Model 213.066/071/266/271 2# | Model 213.005/040/042/04 3/045/049/076/077/0 78/086/087/205/217/242/243/245/277/27 8/279/287 Model 213.066/071/266/27 1 1# | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-04O | Press-in dimension "a" from face end of pilot bushing to joint flange | Front propeller shaft | mm | 24, 80 | 23, 30 |
| Rear propeller shaft | mm | 28, 30 | 26, 80 | ||
CHECK VALUES FOR PILOT BUSHING ON PROPELLER SHAFT
| Number | Designation | Model 213.020/022/033/050/122/131/220/222/23 3 | Model 213.048 with code 700 (Technology Local Content China) | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-04O | Press-in dimension "a" from face end of pilot bushing to joint flange | Front propeller shaft | mm | 25, 30 | 23, 30 |
| Rear propeller shaft | mm | 28, 80 | 28, 30 | ||
CHECK VALUES FOR PILOT BUSHING ON PROPELLER SHAFT
| Number | Designation | Model 213.140/142/143/16 3/176/177/178/186 | ||
|---|---|---|---|---|
| BE41.10-P-1001-04O | Press-in dimension "a" from face end of pilot bushing to joint flange | Front propeller shaft | mm | 23, 30 |
| Rear propeller shaft | mm | 23, 30 | ||
CHECK VALUES FOR PILOT BUSHING ON PROPELLER SHAFT
| Number | Designation | Model 238.314/323/348/385/423/485 | Model 238.315 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-04P | Press-in dimension "a" from face end of pilot bushing to joint flange | Front propeller shaft | mm | 24, 80 | 23, 30 |
| Rear propeller shaft | mm | 36, 30 | 34, 80 | ||
CHECK VALUES FOR PILOT BUSHING ON PROPELLER SHAFT
| Number | Designation | Model 238.343/378/487 | ||
|---|---|---|---|---|
| BE41.10-P-1001-04P | Press-in dimension "a" from face end of pilot bushing to joint flange | Front propeller shaft | mm | 23, 30 |
| Rear propeller shaft | mm | 26, 80 | ||
- Press in new pilot bushing using a suitable drift. Model 213 Model 253 Model 205 Model 238
Observe the pressing-in dimension (a) from the front of the pilot bushing to the flang, depending on the thickness of the flexible disks, the specified pressing-in dimension (a) may deviate, for example in vehicles equipped with vibration dampers. In these cases the pressing-in dimension (a) measured prior to removal should be used for installation.