Remove/install front bumper - AR88.20-P-2000EW
MODEL 207
MODEL 212 up to model year 2014
Shown on MODEL 212 on right side of vehicle
Shown on model 207 as of model year 2014
| Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. | AS00.00-Z-0010-01A | |
| Information on preventing damage to electronic components due to electrostatic discharge | AH54.00-P-0001-01A | ||
| Remove/install | |||
| 1 | Disconnect battery ground line | MODEL 207 with CODE U60 (Active Bonnet (Pedestrian protection)) MODEL 212 up to model year 2014 with CODE U60 (Active Bonnet (Pedestrian protection)) |
|
| AR54.10-P-0003EW | |||
| 2 | Lift vehicle on vehicle lift | ||
| 3.1 | Remove radiator paneling (13) | MODEL 212 up to model year 2014 |
|
| AR88.40-P-4001EW | |||
| 3.2 | Loosen radiator grille (13) at top of radiator support | MODEL 207 | |
| AR88.40-P-4001EC | |||
| 4 | Pivot left and right air duct insert (4) to side and unscrew bolts (5) | MODEL 207 Gap dimensions on hoods, doors and lids |
AR60.00-P-0700-01EC |
| Gap dimensions on hoods, doors and lidsMODEL 212 up to model year 2014 MODEL 207.3 |
AR60.00-P-0700-01EW | ||
| MODEL 207.4 | *BE60.00-P-1001-01W | ||
| MODEL 212.0/1 up to model year 2014 MODEL 212.2 up to model year 2014 |
*BE60.00-P-1001-01U | ||
| Figure | |||
| 5 | Remove left and right quick-release coupling (3) | MODEL 207 up to model year 2014 MODEL 212 up to model year 2014 |
|
| 6 | Detach left and right fender liner front section in area of bumper | AR88.10-P-1300ELX | |
| 7 | Unscrew bolts (9) on left and right fender (2) | ||
| 8 | Disconnect electrical connector on frame wiring harness and front bumper (X2638) | ||
| 9 | Disconnect electrical connector (6) from left daytime running light (E1/3) or left front fog lamp and right daytime running lamp (E2/3) or right front fog lamp and expose electrical wiring harness | ||
| 10.1 | Remove bottom section of soundproofing at front | MODEL 207 with ENGINE 642, 651 | |
| AR94.30-P-5300EW | |||
| 10.2 | Remove front engine compartment paneling | MODEL 207 with ENGINE 271, 272, 273, 274, 276, 278 | |
| AR61.20-P-1105EW | |||
| 11 | Unscrew bolt (7) form left and right bracket (8) | ||
| 12 | Disconnect electrical connector (11) and unclip electrical wiring harness (12) from radiator trim (13) | MODEL 207 as of model year 2014 with CODE 501 (360 degree camera) |
|
| 13 | Guide bumper (1) out left and right bracket (8) | ||
| 14 | Remove bumper (1) toward front | ||
| General information on the impact absorber | AH88.20-P-1000-01A | ||
| 15 | Disassemble bumper (1) | When replacing bumper (1). | |
| MODEL 207 up to model year 2014 MODEL 212 up to model year 2014 |
AR88.20-P-2050EW | ||
| MODEL 207 as of model year 2014 |
AR88.20-P-2050EWN | ||
| Check | |||
| 16 | Check left and right pedestrian sensor (10) for damage of any kind (cracks, holes, kinks, etc.) | MODEL 207 as of model year 2014 with CODE U60 (Active Bonnet (Pedestrian protection)) If damages are visible: Replace pedestrian protection sensor (10). |
|
| AR91.60-P-0950EWM | |||
| 17 | Install in the reverse order | ||
| 18 | Check adjustment of left front fog lamp and right front fog lamp, adjust | MODEL 207 without CODE 615 (Bi-xenon headlamps with active light function) without CODE 616 (Bi-xenon headlamp unit with integrated asymmetric curve illumination) without CODE 621 (Intelligent Light System (left-hand traffic)) without CODE 622 (Intelligent Light System) MODEL 212 up to model year 2014 without CODE 615 (Bi-xenon headlamps with active light function) |
|
| AP82.10-P-8260EW | |||
| 19 | Calibrate 360° camera in front with diagnostic system | MODEL 207 as of model year 2014 with CODE 501 (360 degree camera) |
|
| AD00.00-P-2000-04A |
CHECK VALUES FOR GAP DIMENSIONS
| Number | Designation | MODEL 212.0/1 | MODEL 212.2 | |||
|---|---|---|---|---|---|---|
| BE60.00-P-1001-01U | Gap dimension | Engine hood to fender | Dimension "A" | mm | 4 (±1) | 4 (±1) |
| Engine hood to headlamp | Dimension "B" | mm | 4 (±1) | 4 (±1) | ||
| Engine hood to radiator grille | Dimension "C" | mm | - | - | ||
| Engine hood to bumper | Dimension "D" | mm | 4, 5 (±1, 5) | 4, 5 (±1, 5) | ||
| Engine hood to A-pillar | Dimension "E" | mm | 4, 5 (±1, 5) | 4, 5 (±1, 5) | ||
| Bumper to headlamp | Dimension "F" | mm | 3, 5 (±1, 5) | 3, 5 (±1, 5) | ||
| Picture | AR60.00-P-0700-01E W | AR60.00-P-0700-01E W | ||||
CHECK VALUES FOR GAPS
| Number | Designation | MODEL 207.3 | MODEL 207.4 | |||
|---|---|---|---|---|---|---|
| BE60.00-P-1001-01W | Gap dimension | Engine hood to fender | Dimension "A" | mm | 4 (±1) | 4 (±1) |
| Engine hood to headlamp | Dimension "B" | mm | 4 (±1) | 4 (±1) | ||
| Engine hood to bumper | Dimension "C" | mm | 6 (+1/-2) | 6 (+1/-2) | ||
| Engine hood to A-pillar | Dimension "D" | mm | 4, 5 (+2/-1) | 4, 5 (+2/-1) | ||
| Bumper to headlamp | Dimension "E" | mm | 2, 5 (±1, 5) | 2, 5 (±1, 5) | ||
| Picture | AR60.00-P-0700-01E C | AR60.00-P-0700-01E C | ||||