Retrofit Wiring Harness For Mercedes-Benz Dashcam At Front - AZ54.71-P-0002-01LWE
Model 213
| Notes on the use of paint scraping nuts on ground connections | AH00.19-P-1000-20A | |||
| Information on preventing damage to electronic components due to electrostatic discharge | AH54.00-P-0001-01A | |||
| Notes on retrofitting electrical/optical lines | AH82.00-P-0000-01A |
| Number | Designation | Model 213 | ||
|---|---|---|---|---|
| BA00.19-P-1013-02A | Left front footwell ground point | W15/5 | Nm | 10 |
| Number | Designation | Order number |
|---|---|---|
| BR00.45-Z-1144-02A | Adhesive tape roll, non-woven Tesa tape, 50 meters, 50 mm wide | A 008 989 50 85 09 |
Connection scheme
Routing diagram
- Route dashcam wiring harness (8) from dashcam mount at front under the roof lining to the left to the A-pillar.
- Fasten ferrite core of dashcam wiring harness (8) using cable ties (arrows A) to overhead control panel mount (36).
- Route the three single lines of the dashcam wiring harness (8) above the window airbag (30).
- Route the three single lines of the dashcam wiring harness (8) above the window airbag (30) and into the footwell.
Route the three individual lines of the dashcam wiring harness (8) behind the crossmember for the instrument panel.
- Route ground line (8.10) of dashcam wiring harness to left front footwell ground point (W15/5) and connect.
For overcrowded assignment, use the left footwell ground point (W34).
- Remove violet connector socket (MR2) from front SAM control unit (N10/6).
- Remove gray 21-pin connector socket insert from violet connector socket (MR2).
- Remove line (20) from contact cavity "29" of gray 21-pin connector socket insert (19).
or the supplementary passenger car wiring harness repair kit
- Install line (20) into free contact cavity of blue 2-pin connector socket (8.3) of dashcam wiring harness (8).
- Lock blue 2-pin connector socket (8.3) into place.
- Install line (8.8) of Y-line (8.7) into contact cavity "29" of gray 21-pin connector socket insert (19).
- Install gray 21-pin connector socket insert into violet connector socket (MR2).
- Attach violet connector socket (MR2) to front SAM control unit (N10/6).
- Connect blue 2-pin connector socket (8.3) of dashcam wiring harness (8) to blue 2-pin plug (8.9) of Y-line (8.7).
- Remove electrical fuse (29) from slot 210 (arrow B) of driver's side fuse and relay module (K40/6).
- Release yellow fuse holder (24) on driver's side fuse and relay module (K40/6).
- Remove red/black line (25) from contact cavity "7" (arrow C) of yellow fuse holder (24).
- Install red line (8.12) of Y-line (8.6) into contact cavity "7" (arrow C) of yellow fuse holder (24).
- Lock yellow fuse holder (24) on driver's side fuse and relay module (K40/6) into place.
- Install removed red/black line (25) into free contact cavity of fuse holder (8.4) of Y-line (8.6).
- Install lock (8.13) into fuse holder (8.4) (arrow D).
- Install electrical fuse (29) into fuse holder (8.4).
- Connect both fuse holders (8.4, 8.5) of dashcam wiring harness (8).
- Install electrical fuse parts kit (55) into slot 210 (arrow B) of driver's side fuse and relay module (K40/6).
- Push damping (39) to one side.
- Route branch-off line no longer required for dashcam at rear up to installation location of fuse and relay module on driver's side.
- Plug black plug (8.1) of dashboard wiring harness (8) into a felt-shaped pocket (40).
- Fasten pocket (40) using fabric tape (41) to wiring harness for dashcam (8).
- Tie down branch-off line for dashcam at rear and fix in place in installation space behind the driver's side fuse and relay module.
- Position damping (39).
- Strap down excess lengths of dashcam wiring harness in area of A-pillar.
- Finally, fasten the dashcam wiring harness onto the roof lining using adhesive felt tape.