LEMON Manuals: Even more car manuals for everyone
Home >> Mercedes Benz >> 2017 >> C300 Base, 2D Convertible >> Repair and Diagnosis >> Body & Frame >> Mirrors >> Interior Equipment - 205 Chassis >> Testing & Repair >> Remove/Install Rear Shelf >> Remove/Install Rear Shelf - AR68.30-P-4581LW

Remove/Install Rear Shelf - AR68.30-P-4581LW

Model 205.0/1 

Model 213.0 

G13023649Courtesy of MERCEDES-BENZ USA

Shown on model 205.0 with code 287 (Folding seat backrest in rear), code 540 (Electric roller sun blind for rear window) and code 810 (Sound system) 

G13023650Courtesy of MERCEDES-BENZ USA

Shown on model 205.0 with code 287 (Folding seat backrest in rear), code 540 (Electric roller sun blind for rear window) and code 810 (Sound system) 

G13023651Courtesy of MERCEDES-BENZ USA

Shown on model 205.0 with code 287 (Folding seat backrest in rear), code 540 (Electric roller sun blind for rear window) and code 810 (Sound system 

WARNING Risk of injury  caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof. No parts of the body or limbs should be within the operating area when the components are moving. AS00.00-Z-0011-01A
  Notes on sensor system for trunk lid opening/closing   AH80.61-P-0001-01A
REMOVINGINSTALLING Remove/install     
1 Remove both side bolsters Model 205.0/1
with code 287 (Foldable seat backs in the rear)
Model 213.0
with code 287 (Foldable seat backs in the rear)		 AR91.12-P-1710LW
2 Unlock all backrests and fold over Model 205.0/1
with code 287 (Foldable seat backs in the rear)
Model 213.0
with code 287 (Foldable seat backs in the rear)		  
3 Remove seat backrest Model 205.0/1
except code 287 (Foldable seat backs in the rear)
Model 213.0
except code 287 (Foldable seat backs in the rear)		 AR91.12-P-1620LW
4 Remove anchor fitting on center seat belt Model 205.0/1
except code 287 (Sitzlehnen im Fond klappbar)
Model 213.0
except code 287 (Sitzlehnen im Fond klappbar)
IMPORTANTInstallation:  Ensure bulb is correctly installed.
TORQUE SPECIFICATION Bolt, rear belt end fitting		 *BA91.40-P-1005-01U 
5 Remove both C-pillar trims and guide out of working area along seat belts Model 205.0/1 AR68.30-P-4490LW 
    Model 213.0 AR68.30-P-4490LWE
    IMPORTANT Belt end fittings must not be detached.  
6 Remove retaining clips (3) together with spacers (4) SPECIAL TOOL Clip remover Fig 1
7 Slightly fold back foam material (6) and disconnect electrical connectors (5) INSTALLATION NOTESInstallation: 
Completely fold back foam material (6) over electrical connectors (5).
Otherwise noise may occur.
IMPORTANT The number of electrical connectors (5) may vary depending on the equipment.		  
8 Unclip retaining clip (7) SPECIAL TOOL Clip remover Fig 1
9 Unscrew bolt (8) from towing eye bracket (9) and remove towing eye bracket (9) Model 205.0/1
IMPORTANTInstallation:  Hook towing eye bracket (9) into body (2) together with sheet metal clip (10) and clip in.		  
10 Loosen screws (11) Model 205.0/1
with code 540 (Electric sunblind for rear window)
Model 213.0
with code 540 (Electric sunblind for rear window)		  
11 Unlock catches (12) on rear shelf (1) and slightly push rear shelf (1) toward front IMPORTANTInstallation:  Ensure that arrests (12) are seated correctly.  
12 Lift rear shelf (1) and guide center seat belt with anchor fitting through cover (13) of center belt guide Model 205.0/1
except code 287 (Sitzlehnen im Fond klappbar)
Model 213.0
except code 287 (Sitzlehnen im Fond klappbar)		  
13 Remove rear shelf (1) from vehicle IMPORTANT Helper required.  
14 Remove sheet metal clip (10) from body (2) Model 205.0/1
IMPORTANTInstallation:  Screw sheet metal clip (10) to towing eye bracket (9) with bolt (8).		  
15 Remove cover (13) When replacing rear shelf (1).  
16 Remove Isofix coverings (14) When replacing rear shelf (1).  
17 Disconnect electrical connectors from speakers (15) Model 205.0/1
with code 810 (Sound system)
Model 213.0
with code 810 (Sound system)
Model 213.0
with code 811 (Advanced sound system)
When replacing rear shelf (1).		  
18 Remove cover above speakers (15) Model 205.0/1
with code 810 (Sound system)
Model 213.0
with code 810 (Sound system)
Model 213.0
with code 811 (Advanced sound system)
When replacing rear shelf (1).		  
19 Remove speakers (15) Model 205.0/1
with code 810 (Sound system)
Model 213.0
with code 810 (Sound system)
Model 213.0
with code 811 (Advanced sound system)
When replacing rear shelf (1).		  
20 Remove tweeters Model 213.0
with code 811 (Advanced sound system)		  
21 Remove roller sun blind (16) When replacing rear shelf (1).
Model 205.0/1
with code 540 (Electric sunblind for rear window)		 AR68.50-P-3400LW 
    Model 213.0
with code 540 (Electric sunblind for rear window)		 AR68.50-P-3400LWV
22 Remove additional brake lamp (17) When replacing rear shelf (1).
IMPORTANTInstallation:  Replace adhesive strips for fastening electrical wiring harness (18) on additional brake lamp (17).		  
23 Install in the reverse order    
SEAT BELTS/EMERGENCY TENSIONING RETRACTORS

Number Designation Model 205.0 Model 205.1
BA91.40-P-1005-01U Bolt, rear belt end fitting Nm 35 35
SEAT BELTS/EMERGENCY TENSIONING RETRACTORS

Number Designation Model 213
BA91.40-P-1005-01U Bolt, rear belt end fitting Nm 35
Fig 1: Identifying Clip Remover (452 589 01 63 00)
G13023652Courtesy of MERCEDES-BENZ USA
scientia non olet · About LEMON Manuals