Retrofit Backup Camera Wiring Harness In Vehicle Interior - AN54.65-S-0030-09EA
Model 447.6## 1#
With Code W65 (Tailgate)
Except Code W50 (Rear-end door, double-wing, 180 degrees without window)
Except Code W54 (2-wing rear-end door, 270 degrees)
Model 447.7## 1#
With Code D57 (Full-width partition wall on C-pillar with window)
With Code V23 (Interior trim, premium version)
With Code W65 (Tailgate)
With Code ZK4 (Mixto)
Except Code W50 (Rear-end door, double-wing, 180 degrees without window)
Except Code W54 (2-wing rear-end door, 270 degrees)
Model 447.7## 1#
With Code W65 (Tailgate)
Except Code V23 (Interior trim, premium version)
Except Code W50 (Rear-end door, double-wing, 180 degrees without window)
Except Code W54 (2-wing rear-end door, 270 degrees)
| Assignment of right footwell firewall fuse and relay module | Model 447.6## 1# except code XM0 (Facelift) Model 447.7## 1# except code XM0 (Facelift) | GF54.15-S-1256-39TRA | |
| Assignment of right footwell firewall fuse and relay module | Model 447.6## 1# with code XM0 (Facelift) Model 447.7## 1# with code XM0 (Facelift) | GF54.15-S-1256-39TRF |
| Number | Designation | 8.8 | 10.9 | ||
|---|---|---|---|---|---|
| BA00.10-Z-1003-01KOA | M8 | Galvanized | Nm | 23 | 32 |
| Phosphated | Nm | 21 | 29 | ||
| Number | Designation | 12.9 | ||
|---|---|---|---|---|
| BA00.10-Z-1003-01KOA | M8 | Galvanized | Nm | 38 |
| Phosphated | Nm | 36 | ||
Shown on model 447.6 without code SH9 (Window airbag for driver and front passenger)
- Route vehicle interior electrical wiring harness (1) as shown from right D-pillar and top right roof paneling.
Do not kink the vehicle interior electrical wiring harness (1) and ensure it is routed without chafing.
This prevents damage.
- Fasten vehicle interior electrical wiring harness (1) in sections using cable ties to factory-installed electrical wiring harness.
- Remove ventilation scoop (16) using
long wedge.
- Unscrew nut from right D-pillar ground point (W29/10).
- Route ground line (4) from vehicle interior through cable opening in right D-pillar to outside.
This prevents damage.
- Attach ground line (4) to right D-pillar ground point (W29/10).
- Secure ground line (4) to right D-pillar ground point (W29/10) using nut
.
- Install ventilation scoop (16).
- Attach power supply electrical line (2) of vehicle interior electrical wiring harness (1) to power supply electrical line (9) of liftgate electrical wiring harness.
This creates the right tailgate electrical connection 2 (X8/46).
- Attach camera electrical line (3) of vehicle interior electrical wiring harness (1) to camera electrical line (8) of liftgate electrical wiring harness.
Shown on model 447.6 With Code D51 (Full-width partition wall with 1 window without code SH9 (Window airbag for driver and front passenger)
- Route vehicle interior electrical wiring harness (1) as shown along top right roof paneling, under front headliner (14) up to passenger-side footwell.
This prevents damage.
To do this, pass the vehicle interior electrical wiring harness (1) through the opening in the partition wall (13) at the top.
- Fasten vehicle interior electrical wiring harness (1) in sections using cable ties to factory-installed electrical wiring harness.
- Install CAN G electrical line (5) in front end CAN (CAN G) potential distributor electrical connector (X304).
- Install CAN electrical line (17) in interior CAN (CAN B) potential distributor electrical connector (X301).
- Install fuse and relay module electrical line (7) in firewall fuse and relay module (K40/11).
- Route radio electrical line (6) of vehicle interior electrical wiring harness (1) as shown to radio (Audio) (N87/2).
This prevents damage.
- Fasten radio electrical line (6) in sections using cable ties to factory-installed electrical wiring harness.
- Connect radio electrical line (6) to radio (Audio) (N87/2).