Replace Shock Absorber Mount On Lower Wishbone - AR32.25-P-0107GZ

MODEL 164, 166, 292 Front axle 

Courtesy of MERCEDES-BENZ USA

	Notes on self-locking nuts and bolts		AH00.00-N-0001-01A
	Notes on repair work on suspension components		AH00.00-P-0100-01A
	Remove/install
1	Secure vehicle on vehicle lift		AR00.60-P-0100GZ
2	Empty AIRmatic using diagnostic system	Model 164, 166, 292 with code 489 (AIRMATIC) Front axle
		Empty and fill the AIRmatic as per the specifications; the complete wheels must not be touching the ground. The air springs can otherwise be damaged and fail later.	AD00.00-P-2000-04A
3	Detach torsion bar linkage from torsion bar	Detach the torsion bar linkage carefully. The torsion bar is under tension. Model 164.1/8Nut, torsion bar linkage to torsion bar	*BA32.20-P-1004-02L
		Model 166 except code 468 (Active driving stability (stability)) Model 166 with code 468 (Active driving stability (stability)) Model 292 except code 468 (ACTIVE CURVE SYSTEM) Model 292 with code 468 (ACTIVE CURVE SYSTEM) Screw/bolt, link rod to torsion bar	*BA32.20-P-1002-02Q
4	Relieve threaded connection for shock absorber on lower control arm (3) using telescopic lifter
	000 588 11 62 00 Major assembly mount		WS01.00-P-0092B
5	Remove screw/bolt (1)	Model 164.1/8 Self-locking nut, shock absorber to wishbone	*BA32.25-P-1002-01G
		Model 166, 292 Self-locking nut, shock absorber to wishbone	*BA32.25-P-1002-01O
6	Detach steering knuckle from upper transverse control arm	Model 166, 292 Front axle Self-locking nut, upper ball joint out of upper transverse control arm to steering knuckle	*BA33.20-P-1001-01R
7	Lower the lower control arm (3)
8	Press out shock absorber mount (4) toward front	Do not exceed 140 bar pressure. Otherwise the shock absorber mount (4) may be damaged. Use separate parts A and E of the pulling/insertion device (5). Model 164 Front axle Installation:  Use separate parts C and D of the pulling/insertion device (5). Model 166, 292 Front axle Installation:  Use the sleeve and separate part C of the pulling/insertion device (5).
		Hand pump	Fig 4
		Hydraulic hose (complete)	Fig 2
		Threaded spindle	Fig 1
		Hollow cylinder	Fig 5
		Extraction/insertion tool	Fig 6
		Model 166, 292 Front Sleeve	Fig 3
9	Install in the reverse order

FRONT AXLE TORSION BAR

Number	Designation			Model 166 except code 468 (ACTIVE CURVE SYSTEM)	Model 166 with code 468 (ACTIVE CURVE SYSTEM)
BA32.20-P-1002-02Q	Screw/bolt, link rod to torsion bar	Stage 1	Nm	80	80
		Stage 2	∠°	90	90

FRONT AXLE TORSION BAR

Number	Designation			Model 292 except code 468 (ACTIVE CURVE SYSTEM)	Model 292 with code 468 (ACTIVE CURVE SYSTEM)
BA32.20-P-1002-02Q	Screw/bolt, link rod to torsion bar	Stage 1	Nm	80	80
		Stage 2	∠°	90	90

FRONT AXLE TORSION BAR

Number	Designation			Model 164.1/8
BA32.20-P-1004-02L	Nut, torsion bar linkage to torsion bar	Stage 1	Nm	100
		Stage 2: Loosen	∠°	180
		Stage 3	Nm	120
		Stage 4	∠°	45

FRONT AXLE SHOCK ABSORBER

Number	Designation		Model 164.1/8
BA32.25-P-1002-01G	Self-locking nut, shock absorber to wishbone	Nm	265

FRONT AXLE SHOCK ABSORBER

Number	Designation			Model 166	Model 292
BA32.25-P-1002-01O	Self-locking nut, shock absorber to wishbone	Stage 1	Nm	100	100
		Stage 2	∠°	180	180

WHEEL CONTROL, HUB

Number	Designation			Model 166	Model 292
BA33.20-P-1001-01R	Self-locking nut, upper ball joint out of upper transverse control arm to steering knuckle	Stage 1	Nm	100	100
		Stage 2	∠°	45	45

Fig 1: Identifying Threaded Spindle (652 589 00 33 11)

Courtesy of MERCEDES-BENZ USA

Fig 2: Identifying Hydraulic Hose - Complete (652 589 00 33 23)

Courtesy of MERCEDES-BENZ USA

Fig 3: Identifying Sleeve (166 589 01 14 00)

Courtesy of MERCEDES-BENZ USA

Fig 4: Identifying Hand Pump (652 589 00 33 21)

Courtesy of MERCEDES-BENZ USA

Fig 5: Identifying Hollow Cylinder (652 589 00 33 22)

Courtesy of MERCEDES-BENZ USA

Fig 6: Identifying Extraction/Insertion Tool (164 589 00 43 00)

Courtesy of MERCEDES-BENZ USA