Check and correct the adjustment of the headlamps - AP82.10-P-8260M

WARNING: This page does not describe the selected car, but rather 203 other vehicles, including the 2020 Mercedes-Benz SLC300, 2020 Mercedes-Benz SL550, 2020 Mercedes-Benz SL450, 2020 Mercedes-Benz S65 AMG, and 2020 Mercedes-Benz GLA250. However, it is still accessible from the selected car via links, so may be relevant.

MODEL 215, 220

MODIFICATION NOTES

15.1.08

Set switch for headlamp range adjustment to 0 position, added

Step 8.1

	Check
	Risk of death caused by high voltage levels present at xenon headlamps. Risk of explosion/fire hazard due to highly flammable substances in the area of damaged xenon bulbs Risk of injury due to UV light, hot components on xenon headlamps and glass splinters when xenon bulbs burst Risk of poisoning caused by inhalation of mercury vapors and by toxic salts and mercury compounds being ingested or coming into contact with skin	Do not come into contact with parts that are under high voltage. Persons with active electronic implants (e.g. heart pacemakers) must never work on xenon headlamps. Switch off entire lighting system. Wear insulated safety shoes, safety glasses and protective gloves. Remove highly inflammable materials from the hazard area. Ensure sufficient ventilation in the working area.	AS82.10-Z-0001-01A
	Risk of accident caused by vehicle starting off by itself when engine is running. Risk of injury caused by contusions and burns during starting procedure or when working near the engine as it is running	Secure vehicle to prevent it from moving by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts.	AS00.00-Z-0005-01A
1	Check tire inflation pressure, correct if necessary
2	Park vehicle on horizontal, level surface	Vehicle must be in curb condition (curb weight, fuel tank full or corresponding additional weight).
3	Have person sit on driver seat or place load of 75 kg on seat	Except vehicles with code 494 USA version or vehicles with code 489 AIRmatic (air suspension with level adjustment and adaptive dampening system (ADS))
4	Allow engine to run for approx. 30 s at mid-range speed and press level control switch	Afterwards, the height of the vehicle has to be at a normal level. Move vehicle back and forth to correctly adjust axles.
5	Prepare headlamp aimer	Align headlamp aimer approx. 50 cm in front of the headlamps parallel with the vehicle at the height of light source. Adjust specified headlamp inclination on scale of headlamp aimer. Headlamp aimer gotis://E_82_01.0
6	Start the engine and switch on low beam
7.1	Check function of headlamp range adjustment by adjusting headlamp range adjustment switch	Except vehicles with code 614 Bi-xenon headlamp unit or vehicles with code 494 USA version Both light beams of the headlamps must be evenly adjusted.
7.2	Check function of headlamp range adjustment through placement of additional weights in the luggage compartment	Vehicles with code 614 Bi-xenon headlamp unit or vehicles with code 494 USA version The height of the light-dark boundary shall not change when loading or unloading the weights.
8.1	Move the switch for headlamp range adjustment at the switch for exterior lights (S1) into position 0	Except vehicles with code 614 Bi-xenon headlamp unit or vehicles with code 494 USA version
8.2	Remove additional weights from the luggage compartment	Vehicles with code 614 Bi-xenon headlamp unit or vehicles with code 494 USA version
9	Check low beam, if required correct setting	Vehicles with code 614 Bi-xenon headlamp unit or vehicles with code 494 USA version, correct adjustment subject to separate repair order.	AP82.10-P-8260-01A
10	Check setting of high beam	Vehicles with code 614 Bi-xenon headlamp unit or vehicles with code 494 USA version, correct adjustment subject to separate repair order.	AP82.10-P-8260-02A
11	Check fog lamp, if required correct setting		AP82.10-P-8260-04A
12	Switch off light and turn off engine