Retrofit Mercedes-Benz InCar Internet control unit - AZ82.85-P-0005-04EW

MODEL 212.0## /2## 1# 

Connection diagram with code (518) Media interface 

Fig 1: Incar Internet Control Unit Connection Diagram (With Code 518)

Courtesy of MERCEDES-BENZ USA

Connection diagram without code (518) Media Interface 

Fig 2: Incar Internet Control Unit Connection Diagram (Without Code 518)

Courtesy of MERCEDES-BENZ USA

Routing diagram with code (518) Media interface 

Fig 3: Incar Internet Control Unit Wiring Harness Routing Diagram (With Code 518)

Courtesy of MERCEDES-BENZ USA

Routing diagram without code (518) Media Interface 

Fig 4: COMAND Control Unit Wiring Harness Routing Diagram (Without Code 518)

Courtesy of MERCEDES-BENZ USA

1. Connect black, 32-pin coupling (5) of InCar Internet adapter wiring harness (3), coupling for LVDS display wiring harness (15.2) of LVDS display wiring harness (15) and coupling for LVDS head unit wiring harness (16.2) of LVDS head unit wiring harness (16), as shown, to InCar Internet control unit (1).
   Fig 5: LVDS Head Unit Wiring Harness And Incar Internet Control Unit

   Courtesy of MERCEDES-BENZ USA
2. Remove air duct (26)
   Fig 6: Air Duct

   Courtesy of MERCEDES-BENZ USA
3. Route cable ties through holes (arrows A) and holder (arrow B).

   The cable ties are used to fasten the InCar Internet control unit.

   Fig 7: Routing Cable Ties Through Holes And Holder

   Courtesy of MERCEDES-BENZ USA
4. Route InCar Internet adapter wiring harness (3), LVDS display wiring harness (15) and LVDS head unit wiring harness (16) to the InCar Internet control unit (1) and fasten in place using felt tape (24) as shown.
5. Install InCar Internet control unit (1), as shown, and fasten in place using previously positioned cable ties (23).

   Route cable ties through attachment points on InCar Internet control unit (1) and tighten.

   The InCar Internet control unit (1) must be fixed so that any noise development is prevented.

   Fig 8: Incar Internet Control Unit And Cable Ties

   Courtesy of MERCEDES-BENZ USA
6. Route excess length of InCar Internet adapter wiring harness (3), of LVDS display wiring harness (15) and LVDS head unit wiring harness (16) behind the floor covering on the passenger-side (25) in loops.
7. Place glove box (22) into footwell on passenger-side.
   Fig 9: Incar Internet Adapter Wiring Harness And Glove Box

   Courtesy of MERCEDES-BENZ USA
8. Connect blue 1-pin connecting cable coupling (2.1) of connecting cable (2) to InCar Internet control unit (1).
   Fig 10: Incar Internet Control Unit And Cable

   Courtesy of MERCEDES-BENZ USA
9. Detach white 4-pin coupling (3.1) and white 4-pin connector (3.2) of InCar Internet adapter wiring harness (3).

   In vehicles with  code (518) Media Interface.

10. Connect white 4-pin coupling (3.1) with white 4-pin connector (14.1) of media interface adapter line (14).

    In vehicles with  code (518) Media Interface.

    Fig 11: Media Interface Adapter Line Wiring Harness Routing Diagram

    Courtesy of MERCEDES-BENZ USA
11. Connect black 1-pin coupling (18.1) of media interface electrical connector adapter line (18) to adapter wiring harness for intelligent head unit.

    In vehicles with  code (518) Media Interface.

12. Connect black 24-pin plug (18.2) with media interface electrical connector.

    In vehicles with  code (518) Media Interface.

    Fig 12: Media Interface Electrical Connector Adapter Line Coupling

    Courtesy of MERCEDES-BENZ USA
13. Install air duct (26).
    Fig 13: Air Duct

    Courtesy of MERCEDES-BENZ USA