Audio/COMAND operating instructions - GF82.85-P-0014-11FQJ

Audio system, general 

The following components are available for control of the audio system:

• Control buttons on the COMAND controller unit (A40/3)
• Audio/COMAND control panel (A40/9)

  (call basic menu and make settings)

• Left multifunction steering wheel button group (S110) and right multifunction steering wheel button group (S111)

  (volume, telephone functions)

• Hands-free system microphone (A67b1)

The Audio/COMAND display (A40/8) provides menu guidance.

The following basic functions can be controlled:

• "RADIO" basic function 
• )"DISC" basic function 
• Basic video and TV function 
• "NAVI" basic function 
• )"TEL" basic function 
• "SYS" basic function 

"RADIO" basic function 

"RADIO" basic function can be called by pressing the "RADIO" function key. Pressing it several times enables you to switch between the following frequency bands:

• "FM"
• "AM"

When the "RADIO" basic function is called, the corresponding basic mask appears. The following information appears on the audio/COMAND display (A40/8):

• Currently set frequency
• Current station from global positioning system (GPS) list (location specific) and memory location (if stored)
• Cursor, with which a different station can be selected
• Application bar with corresponding main menus (top)
• Function bar with corresponding submenus (bottom)

The following audio sources can be selected in the application bar:

• "FM"
• "AM"
• "Disk"
• "Memory Card"
• "Music Register"
• "Media interface"
• "Aux"

The various menu structures are made visible on the function bar depending on the audio source selected on the application bar.

In the function bar the following submenus can be called up depending on the frequency band selected in the application bar, and then various settings can be made:

• "FM 1" submenu (display changes between "FM 1" and "FM 2") (FM 1, FM 2, frequency entry)
• "Presets" submenu

  ("Autostore" (automatic search and storage of 10 stations with strongest reception))

• "Sound" submenu

  ("Treble", "Bass", "Bal/Fad", "Logic7®" (with code (810) Sound system))

• "AM 1" submenu (display changes between "AM 1" and "AM 2")

  (AM 1, AM 2, frequency entry)

• "TI/Back to AM" submenu (change of "TI" display (Traffic information (fixed frequency at 1620 kHz)) or "Back to AM")
• "Presets" submenu

  ("Autostore" (Automatic search and storage of 10 stations with strongest reception) and list of stored stations)

• "Sound" submenu

  ("Treble", "Bass", "Bal/Fad", "Logic7®" (with code (810) Sound system))

)"DISC" basic function 

The "DISC" basic function can be called by pressing the "DISC" function key. The corresponding basic mask appears. The following information appears on the audio/COMAND display (readable data carrier inserted):

• Number of tracks on CD or DVD
• Current track with elapsed play time
• Artist (if present on CD or DVD)
• Application bar with corresponding main menus (top)
• Function bar with corresponding submenus (bottom)

The various menu structures are made visible on the function bar depending on the audio source selected on the application bar.

When an audio CD/DVD is inserted, the following submenus can be called in the function bar and various settings made:

• "CD" submenu

  (Normal track sequence, random track sequence, Gracenote Media Database)

• "Record" submenu (audio files are copied as MP3 files onto the hard disk)
• "Tracks" submenu (track list on CD/DVD)
• "Medium" submenu

  (1 CD/DVD, 2 memory card, 3 Music Register, 4 Media Interface, 5 Bluetooth® audio)

• "Sound" submenu

  ("Treble", "Bass", "Bal/Fad", "Logic7®" (with code (810) Sound system))

A track in the track list can be selected with the control buttons on the radio or on the audio/COMAND control panel. The playback position can be changed by pushing and holding the audio/COMAND controller to the right (forward) or left (back).

When a MP3-CD/DVD is inserted, the following submenus can be called in the function bar and various settings made:

• Submenu "MP3"

  (Normal track sequence, random track sequence, Gracenote Media Database)

• "Folder" submenu

  (folder list and track list on CD/DVD)

• "Medium" submenu

  (1 CD/DVD, 2 memory card, 3 Music Register, 4 Media Interface, 5 Bluetooth® audio)

• "Sound" submenu

  ("Treble", "Bass", "Bal/Fad", "Logic7®" (with code (810) Sound system))

When a memory card is inserted, the following submenus can be called in the function bar and various settings made:

• "Memory Card" submenu

  (Normal track sequence, random track sequence, random folder)

• "Folder" submenu

  (folder list and track list on memory card)

• "Medium" submenu

  (1 CD/DVD, 2 memory card, 3 Music Register, 4 Media Interface, 5 Bluetooth® audio)

• "Sound" submenu

  ("Treble", "Bass", "Bal/Fad", "Logic7®" (with code (810) Sound system))

If the "Music Register" data source is selected, the function bar can be used to call up the following submenus and enable various settings to be made:

• "Music Register" submenu

  (Normal track sequence, random track sequence, random folder, delete all music files, memory info)

• "Folder" submenu

  (folder list and track list in "Music Register")

• "Medium" submenu

  (1 CD/DVD, 2 memory card, 3 Music Register, 4 Media Interface, 5 Bluetooth® audio)

• "Sound" submenu

  ("Treble", "Bass", "Bal/Fad", "Logic7®" (with code (810) Sound system))

When "Media interface" is selected as the data source, the following submenus can be selected in the function bar and various settings made.

"iPod" connected:

• "Media Interface"

  (Normal track sequence, random track sequence, category title)

• "Music" submenu

  ("Current Track List", "Playback Lists", "Artists", "Albums", "Track", "Music Styles", "Composers", "Audio Books")

• "Medium" submenu

  (1 CD/DVD, 2 memory card, 3 Music Register, 4 Media Interface, 5 Bluetooth® audio)

• "Sound" submenu

  ("Treble", "Bass", "Bal/Fad", "Logic7®" (with code (810) Sound system))

Universal Serial Bus (USB) stick connected:

• "Media Interface" submenu

  (Normal track sequence, random track sequence, Gracenote Media Database)

• "Music" submenu

  (directories and track lists)

• "Medium" submenu

  (1 CD/DVD, 2 memory card, 3 Music Register, 4 Media Interface, 5 Bluetooth® audio)

• "Sound" submenu

  ("Treble", "Bass", "Bal/Fad", "Logic7®" (with code (810) Sound system))

AUX device connected:

• "AUX" submenu
• "Sound" submenu

  ("Treble", "Bass", "Bal/Fad", "Logic7®" (with code (810) Sound system), standard boost)

Video and TV 

The video and TV function can be displayed on the audio/COMAND control panel in the menu item Audio on the application bar on the audio/COMAND display. The last video or TV application executed is started.

To start a different video or TV application, it is necessary to go back to the application bar and select the menu item Video.

The following video sources can be selected via the Video menu item:

• TV
• Video DVD

Both the video sources TV and DVD video can be activated with the audio/COMAND control panel. The TV or DVD video image appears on the play field on the audio/COMAND display.

The following submenus can be selected on the function bar:

• "DVD-V", "TV 1" or "TV 2" submenu (display changes to match selection)

  (e.g. brightness, contrast, color, saturation, 16:9 optimized, 4:3, wide screen, main, sub; only DVD: DVD functions, medium; only TV: TV 1, TV 2, enter TV channel)

• "Presets" submenu

  ("Autostore" (automatic search and storage of 10 stations with strongest reception))

• "Sound" submenu

  ("Treble", "Bass", "Bal/Fad", "Logic7®" (with code (810) Sound system))

"NAVI" basic function 

The map and language data are preinstalled on the hard disk of the COMAND controller unit. The card data can be updated by the customer or workshop by installing the data from an update DVD. Installation is also possible while driving.

After inserting the update DVD into the COMAND controller unit, a prompt automatically appears asking whether the data is to be installed. After confirmation, installation is accomplished. If installation fails (e.g. due to dead vehicle battery (G1) or damaged DVD), operation can be continued with the old data. After installation, the DVD can be removed.

The "NAVI" basic function can be called by pressing the "NAVI" function key. The default screen appears on the Audio/COMAND display with the following information:

• Current location
• Application bar with corresponding main menus (top)
• Function bar with corresponding submenus (bottom)

Application bars and function bars are not shown on the Audio/COMAND display in the full-screen mode. The full-screen mode can be activated via the audio/COMAND control panel.

The basic navigation function can be operated as follows:

D Selection or settings via application bar 

D Selection or settings via function bar 

Selection and settings can be made with the buttons on the COMAND control unit, on the audio/COMAND control panel or by voice control in the VCS.

Selection or settings via application bar 

The navigation menu allows the following operating functions, some of which include additional subfunctions:

• Destination entry (e.g. with map, 50 characters (Japanese keyboard), points of interest, telephone numbers, ZIP codes, address book, previous destinations, memory points)
• Memory Points
• Points of interest (e.g. at current position, along route, at destination)
• Vehicle Information and Communication System (VICS) information (e.g. test, diagram, interrupt, set)
• Settings (e.g. navigation, VICS, Edit Position, avoid options)
• Home (e.g. guidance, enter, delete)
• Diagram
• Discontinue or continue route guidance

Selection or settings via function bar 

The following control functions can be activated with the function bar, some of these include additional subfunctions:

• Display (e.g. view (2D, 3D, buildings), map (HWY Facility, Metro Highway Map, Guidance Display, VICS Public, VICS Highway), alignment, 3D Map Rotation, show points of interest, list points of interest)
• Route (e.g. detour (0.5 to 10 km), recalculate, different route (recommended, toll road, public roads, short route, other), route summary (duration, distance, etc.), route information (map view, route browser, etc., learn route)
• Route guidance (points of interest not available)
• Save (memory point, address book)
• Destination (destination entry, stopover, delete, etc.)
• Repeat (voice output of last message)

)"TEL" basic function 

The "TEL" basic function can be called by pressing the "TEL" function key and allows operation of the vehicle telephone system. When the "TEL" basic function is called, the corresponding basic mask appears. The following information appears on the Audio/COMAND display:

• Name of currently connected mobile phone
• Field strength of mobile telephone network
• Handset symbol
• Speller with characters for entering telephone numbers
• Application bar with corresponding main menus (top)
• Function bar with corresponding submenus (bottom)

Control of the telephone system is described as follows:

• Search and connect Bluetooth® mobile phones 
• Selection or settings via application bar 
• Selection or settings via function bar 
• Complete and terminate telephone connection 

Search and connect Bluetooth® mobile phones 

Mobile phones unknown to the system can be activated with the basic function "Tel", in the "Telephone" menu item and the "Bluetooth telephone" submenu item.

A list of mobile phones already recognized is displayed. This is where you can select and authorize the desired mobile phone. The "Update" entry is used to search for new mobile phones. After the update, it is possible to search and authorize the mobile phone to be connected from the displayed list. Only Bluetooth® telephones are displayed. The transmission and reception volume can be set in the range of 2 to +2 by selecting the mobile phone displayed and then selecting the options or details.

Connection of Bluetooth® devices:

Bluetooth devices can be listed by selecting the following menus on the Audio/COMAND display:

• "System"
• "System settings"
• "Bluetooth"
• "Bluetooth device list"

A telephone connection can be completed as follows:

• Entry of telephone number
• Selection of telephone book entries
• Selection of telephone numbers from call lists

Incoming calls are signaled visually on the Audio/COMAND display as well as acoustically.

Selection or settings via application bar 

In the application bar, the following submenus can be called and various settings made:

• "Phone" menu
• "Address Book" menu
• "FM Multiplex" menu

The address book is not a temporary creation. The entries remain stored in the COMAND controller unit when the mobile phone is removed and can still be dialed.

In the "FM Multiplex" submenu, information on earthquake warnings, tsunami warnings, stock exchange and weather is displayed. While driving only trip-relevant information is displayed.

Selection or settings via function bar 

In the function bar, the following submenus can be called and various settings made:

• "Phone" submenu

  (Bluetooth® telephones, "Private Mode", import contacts, delete contacts, international dialing, volume settings, switch off phone)

• "Own Number"
• "Call lists" (received, dialed)
• "Address book" submenu

  (Import contacts, delete contacts)

• "Search"
• "New"
• "Delete"
• "FM Multiplex" submenu

  (Icons for navigating within information text on pages)

"SYS" basic function 

The "SYS" basic function can be called by pressing the "SYS" function key. The corresponding basic mask appears. The following information appears on the audio/COMAND display:

• Symbol for "SYS" basic menu
• Application bar with corresponding main menus (top)
• Function bar with corresponding submenus (bottom)

The "SYS" basic function can also be selected in the application bar.

In the function bar, the following submenus can be called and various settings made:

• "System settings"

  (Display (brightness, day design, night design, automatic), Linguatronic (Help, "Echo function"), selection of GUI language, reading speed (fast, medium, slow), reversing camera (switch on with reverse gear, language support, activate Bluetooth®), reset)

• "Time" (Set time, format)
• "Display off"