LEMON Manuals: Even more car manuals for everyone
Home >> Mercedes Benz >> 2015 >> SL400 >> Repair and Diagnosis >> Engine Mechanical >> Blowers, Superchargers & Turbochargers >> Air Intake, Turbocharging - 231 Chassis >> Testing & Repair >> Remove/install low-temperature circuit additional radiator - AR09.41-P-3001RKC

Remove/install low-temperature circuit additional radiator - AR09.41-P-3001RKC

ENGINE 279 in MODEL 231 

MODIFICATION NOTES

26.09.2014 Mixing ratio Coolant   BF20.00-P-1001-04A
Fig 1: Low-Temperature Circuit Additional Radiator Remove/Install Components
G11128450Courtesy of MERCEDES-BENZ USA
DANGER Risk of injury  to skin and eyes suffering scalding from contact with hot coolant spray. Risk of poisoning  from swallowing coolant. Do not open cooling system unless coolant temperature is below 90 °C. Open cap slowly and release the pressure. Do not pour coolant into beverage containers.
Wear protective gloves, protective clothing and safety glasses.
AS20.00-Z-0001-01A
IMPORTANT Notes on coolant   AH20.00-N-2080-01A
REMOVINGINSTALLING Remove/install     
1 Remove front fender liner in fender   AR88.10-P-1300RK
2 Clamp off coolant hoses (1, 2) with clamping devices (3, 4) and disconnect from low-temperature circuit additional radiator (5) IMPORTANT Collect coolant which flows out in a suitable container.
SPECIAL TOOL Clamp
Fig 2
3 Unclip electrical line (6) from low-temperature circuit additional radiator (5)    
4 Unlock charge air cooler circulation pump relay (N10/2kD) and detach upwards out of the bracket (7) and place to one side    
5 Remove nut (8)    
6 Remove screw/bolt (9) and remove low-temperature circuit additional radiator (5)    
7 Install in the reverse order    
8 Pour coolant into the low-temperature circuit   AR09.41-P-6834RKC 
REFER TO CAPACITIES & SPECIFICATIONS Coolant specifications   Coolant (Specification 310.1). See https://bevo.mercedes-benz.com/index.php?language_id=1
REFER TO CAPACITIES & SPECIFICATIONS Anticorrosion/antifreeze agents (Sheet 325.0) IMPORTANT Use clean coolant again. Anticorrosion/antifreeze agents (Specification 325.0). See https://bevo.mercedes-benz.com/index.php?language_id=1
    FLUID SPECIFICATION Coolant mixing ratio *BF20.00-P-1001-04A 
INSPECT Check     
9 Check low-temperature circuit cooling system for leaktightness   AR09.41-P-1010RKC 
DANGER Risk of accident  from vehicle starting off by itself when engine running. Risk of injury  (bruises and burns) resulting from working on the engine while it is being started or when it is running. Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. AS00.00-Z-0005-01A
10 Perform an engine test run; check cooling system low-temperature circuit for proper function    
COOLANT MIXING RATIO

Number Designation Engine all
BF20.00-P-1001-04A Coolant mixing ratio Antifreeze/water Up to -37°C % 50/50
As of -38 °C % 55/45
Specification   Coolant (Specification 310.1). See https://bevo.mercedes-benz.com/index.php?language_id=1
Specification   Anticorrosion/antifreeze agents (Specification 325.0). See https://bevo.mercedes-benz.com/index.php?language_id=1
Specification   Premixed coolant (Specification 326.0). See https://bevo.mercedes-benz.com/index.php?language_id=1
Fig 2: Identifying Clamp (000 589 54 37 00)
G09982233Courtesy of MERCEDES-BENZ USA