Rear axle differential housing - BA35.31-P-1000-02A
WARNING: This page does not describe the selected car, but rather 203 other vehicles, including the 2020 Mercedes-Benz SLC300, 2020 Mercedes-Benz SL550, 2020 Mercedes-Benz SL450, 2020 Mercedes-Benz S65 AMG, and 2020 Mercedes-Benz GLA250. However, it is still accessible from the selected car via links, so may be relevant.
MODEL 124, 129, 140, 163, 170, 199, 201, 202, 208, 210, 211, 215, 220, 230, 240
REAR AXLE DIFFERENTIAL HOUSING
| Number | Designation | MODEL 124 | MODEL 129 | |||
|---|---|---|---|---|---|---|
| BA35.31-P-1001-02A | Bolt, end cover to rear axle differential | Bolt+washer | Nm | 50 | 50 | |
| Flange bolt (TORX, internal serrations) | Stage 1 | Nm | 30 | 30 | ||
| Stage 2 | ∠° | 45 | 45 | |||
| BA35.31-P-1002-02A | Oil filler screw, differential | Nm | 50 | 50 | ||
| BA35.31-P-1003-02A | Oil drain screw for rear axle differential | Nm | 50 | 50 | ||
| BA35.31-P-1004-02A | Locking bolt, vibration damper and rear axle housing to rear axle carrier | Nm | 150 | - | ||
| BA35.31-P-1005-02A | Breather, rear axle differential | Nm | 25 | 30 | ||
| BA35.31-P-1006-02A | Bolt, side bearing cap to rear axle center assembly | Nm | 20 | 20 | ||
| BA35.31-P-1007-02A | Bolt, heat sink to end cover | Nm | - | - | ||
| BA35.31-P-1008-02A | Rear axle differential breather to end cover | Nm | - | - | ||
| BA35.31-P-1009-02A | Rear axle differential breather to rear axle housing | Nm | - | - | ||
| BA35.31-P-1010-02A | Locking bolt, vibration damper and rear axle housing to rear axle carrier | Stage 1 | Nm | - | - | |
| Stage 2 | ∠° | - | - | |||
| BA35.31-P-1011-02A | Oil temperature sensor for rear axle center assembly | Nm | - | - | ||
| BA35.31-P-1012-02A | Threaded insert to differential transmission housing | Nm | - | - | ||
| BA35.31-P-1013-02A | Fitting to threaded insert | Nm | - | - | ||
| BA35.31-P-1014-02A | Union nut, oil hose to fitting | Nm | - | - | ||
| BA35.31-P-1015-02A | Union nut for oil hose to oil pump | Nm | - | - | ||
| BA35.31-P-1016-02A | Banjo bolt for oil hose to oil pump | - | - | |||
| BA35.31-P-1017-02A | Banjo bolt, oil hose to threaded inserted | Nm | - | - | ||
| BA35.31-P-1018-02A | Banjo bolt for oil hose to oil cooler | Nm | - | - | ||
| BA35.31-P-1019-02A | Temperature switch to end cover for differential transmission | Nm | - | - | ||
REAR AXLE DIFFERENTIAL HOUSING
| Number | Designation | MODEL 140 | MODEL 163 | |||
|---|---|---|---|---|---|---|
| BA35.31-P-1001-02A | Bolt, end cover to rear axle differential | Bolt+washer | Nm | 50 | - | |
| Flange bolt (TORX, internal serrations) | Stage 1 | Nm | 30 | - | ||
| Stage 2 | ∠° | 45 | - | |||
| BA35.31-P-1002-02A | Oil filler screw, differential | Nm | 50 | 50 | ||
| BA35.31-P-1003-02A | Oil drain screw for rear axle differential | Nm | 50 | 50 | ||
| BA35.31-P-1004-02A | Locking bolt, vibration damper and rear axle housing to rear axle carrier | Nm | - | - | ||
| BA35.31-P-1005-02A | Breather, rear axle differential | Nm | 30 | - | ||
| BA35.31-P-1006-02A | Bolt, side bearing cap to rear axle center assembly | Nm | 20 | - | ||
| BA35.31-P-1007-02A | Bolt, heat sink to end cover | Nm | - | - | ||
| BA35.31-P-1008-02A | Rear axle differential breather to end cover | Nm | - | - | ||
| BA35.31-P-1009-02A | Rear axle differential breather to rear axle housing | Nm | - | - | ||
| BA35.31-P-1010-02A | Locking bolt, vibration damper and rear axle housing to rear axle carrier | Stage 1 | Nm | - | - | |
| Stage 2 | ∠° | - | - | |||
| BA35.31-P-1011-02A | Oil temperature sensor for rear axle center assembly | Nm | - | - | ||
| BA35.31-P-1012-02A | Threaded insert to differential transmission housing | Nm | - | - | ||
| BA35.31-P-1013-02A | Fitting to threaded insert | Nm | - | - | ||
| BA35.31-P-1014-02A | Union nut, oil hose to fitting | Nm | - | - | ||
| BA35.31-P-1015-02A | Union nut for oil hose to oil pump | Nm | - | - | ||
| BA35.31-P-1016-02A | Banjo bolt for oil hose to oil pump | - | - | |||
| BA35.31-P-1017-02A | Banjo bolt, oil hose to threaded inserted | Nm | - | - | ||
| BA35.31-P-1018-02A | Banjo bolt for oil hose to oil cooler | Nm | - | - | ||
| BA35.31-P-1019-02A | Temperature switch to end cover for differential transmission | Nm | - | - | ||
REAR AXLE DIFFERENTIAL HOUSING
| Number | Designation | MODEL 170 | MODEL 199 | |||
|---|---|---|---|---|---|---|
| BA35.31-P-1001-02A | Bolt, end cover to rear axle differential | Bolt+washer | Nm | - | 40 | |
| Flange bolt (TORX, internal serrations) | Stage 1 | Nm | 30 | - | ||
| Stage 2 | ∠° | 45 | - | |||
| BA35.31-P-1002-02A | Oil filler screw, differential | Nm | 50 | - | ||
| BA35.31-P-1003-02A | Oil drain screw for rear axle differential | Nm | 50 | - | ||
| BA35.31-P-1004-02A | Locking bolt, vibration damper and rear axle housing to rear axle carrier | Nm | - | - | ||
| BA35.31-P-1005-02A | Breather, rear axle differential | Nm | 25 | 25 | ||
| BA35.31-P-1006-02A | Bolt, side bearing cap to rear axle center assembly | Nm | - | - | ||
| BA35.31-P-1007-02A | Bolt, heat sink to end cover | Nm | - | - | ||
| BA35.31-P-1008-02A | Rear axle differential breather to end cover | Nm | - | - | ||
| BA35.31-P-1009-02A | Rear axle differential breather to rear axle housing | Nm | - | - | ||
| BA35.31-P-1010-02A | Locking bolt, vibration damper and rear axle housing to rear axle carrier | Stage 1 | Nm | - | - | |
| Stage 2 | ∠° | - | - | |||
| BA35.31-P-1011-02A | Oil temperature sensor for rear axle center assembly | Nm | - | 17 | ||
| BA35.31-P-1012-02A | Threaded insert to differential transmission housing | Nm | - | - | ||
| BA35.31-P-1013-02A | Fitting to threaded insert | Nm | - | - | ||
| BA35.31-P-1014-02A | Union nut, oil hose to fitting | Nm | - | - | ||
| BA35.31-P-1015-02A | Union nut for oil hose to oil pump | Nm | - | - | ||
| BA35.31-P-1016-02A | Banjo bolt for oil hose to oil pump | - | - | |||
| BA35.31-P-1017-02A | Banjo bolt, oil hose to threaded inserted | Nm | - | - | ||
| BA35.31-P-1018-02A | Banjo bolt for oil hose to oil cooler | Nm | - | - | ||
| BA35.31-P-1019-02A | Temperature switch to end cover for differential transmission | Nm | - | - | ||
REAR AXLE DIFFERENTIAL HOUSING
| Number | Designation | MODEL 201 | MODEL 202 | |||
|---|---|---|---|---|---|---|
| BA35.31-P-1001-02A | Bolt, end cover to rear axle differential | Bolt+washer | Nm | 50 | 50 | |
| Flange bolt (TORX, internal serrations) | Stage 1 | Nm | 30 | 30 | ||
| Stage 2 | ∠° | 45 | 45 | |||
| BA35.31-P-1002-02A | Oil filler screw, differential | Nm | 50 | 50 | ||
| BA35.31-P-1003-02A | Oil drain screw for rear axle differential | Nm | 50 | 50 | ||
| BA35.31-P-1004-02A | Locking bolt, vibration damper and rear axle housing to rear axle carrier | Nm | - | 150 | ||
| BA35.31-P-1005-02A | Breather, rear axle differential | Nm | 25 | 25 | ||
| BA35.31-P-1006-02A | Bolt, side bearing cap to rear axle center assembly | Nm | - | - | ||
| BA35.31-P-1007-02A | Bolt, heat sink to end cover | Nm | - | - | ||
| BA35.31-P-1008-02A | Rear axle differential breather to end cover | Nm | - | - | ||
| BA35.31-P-1009-02A | Rear axle differential breather to rear axle housing | Nm | - | - | ||
| BA35.31-P-1010-02A | Locking bolt, vibration damper and rear axle housing to rear axle carrier | Stage 1 | Nm | - | - | |
| Stage 2 | ∠° | - | - | |||
| BA35.31-P-1011-02A | Oil temperature sensor for rear axle center assembly | Nm | - | - | ||
| BA35.31-P-1012-02A | Threaded insert to differential transmission housing | Nm | - | - | ||
| BA35.31-P-1013-02A | Fitting to threaded insert | Nm | - | - | ||
| BA35.31-P-1014-02A | Union nut, oil hose to fitting | Nm | - | - | ||
| BA35.31-P-1015-02A | Union nut for oil hose to oil pump | Nm | - | - | ||
| BA35.31-P-1016-02A | Banjo bolt for oil hose to oil pump | - | - | |||
| BA35.31-P-1017-02A | Banjo bolt, oil hose to threaded inserted | Nm | - | - | ||
| BA35.31-P-1018-02A | Banjo bolt for oil hose to oil cooler | Nm | - | - | ||
| BA35.31-P-1019-02A | Temperature switch to end cover for differential transmission | Nm | - | - | ||
REAR AXLE DIFFERENTIAL HOUSING
| Number | Designation | MODEL 208 | MODEL 210 | |||
|---|---|---|---|---|---|---|
| BA35.31-P-1001-02A | Bolt, end cover to rear axle differential | Bolt+washer | Nm | - | 50 | |
| Flange bolt (TORX, internal serrations) | Stage 1 | Nm | 30 | 30 | ||
| Stage 2 | ∠° | 45 | 45 | |||
| BA35.31-P-1002-02A | Oil filler screw, differential | Nm | 50 | 50 | ||
| BA35.31-P-1003-02A | Oil drain screw for rear axle differential | Nm | 50 | 50 | ||
| BA35.31-P-1004-02A | Locking bolt, vibration damper and rear axle housing to rear axle carrier | Nm | - | 150 | ||
| BA35.31-P-1005-02A | Breather, rear axle differential | Nm | 25 | 30 | ||
| BA35.31-P-1006-02A | Bolt, side bearing cap to rear axle center assembly | Nm | - | 20 | ||
| BA35.31-P-1007-02A | Bolt, heat sink to end cover | Nm | - | - | ||
| BA35.31-P-1008-02A | Rear axle differential breather to end cover | Nm | - | - | ||
| BA35.31-P-1009-02A | Rear axle differential breather to rear axle housing | Nm | - | - | ||
| BA35.31-P-1010-02A | Locking bolt, vibration damper and rear axle housing to rear axle carrier | Stage 1 | Nm | - | - | |
| Stage 2 | ∠° | - | - | |||
| BA35.31-P-1011-02A | Oil temperature sensor for rear axle center assembly | Nm | - | - | ||
| BA35.31-P-1012-02A | Threaded insert to differential transmission housing | Nm | - | - | ||
| BA35.31-P-1013-02A | Fitting to threaded insert | Nm | - | - | ||
| BA35.31-P-1014-02A | Union nut, oil hose to fitting | Nm | - | - | ||
| BA35.31-P-1015-02A | Union nut for oil hose to oil pump | Nm | - | - | ||
| BA35.31-P-1016-02A | Banjo bolt for oil hose to oil pump | - | - | |||
| BA35.31-P-1017-02A | Banjo bolt, oil hose to threaded inserted | Nm | - | - | ||
| BA35.31-P-1018-02A | Banjo bolt for oil hose to oil cooler | Nm | - | - | ||
| BA35.31-P-1019-02A | Temperature switch to end cover for differential transmission | Nm | - | - | ||
REAR AXLE DIFFERENTIAL HOUSING
| Number | Designation | MODEL 211 | MODEL 215 | |||
|---|---|---|---|---|---|---|
| BA35.31-P-1001-02A | Bolt, end cover to rear axle differential | Bolt+washer | Nm | - | - | |
| Flange bolt (TORX, internal serrations) | Stage 1 | Nm | 30 | 30 | ||
| Stage 2 | ∠° | 45 | 45 | |||
| BA35.31-P-1002-02A | Oil filler screw, differential | Nm | 50 | 50 | ||
| BA35.31-P-1003-02A | Oil drain screw for rear axle differential | Nm | 50 | 50 | ||
| BA35.31-P-1004-02A | Locking bolt, vibration damper and rear axle housing to rear axle carrier | Nm | - | - | ||
| BA35.31-P-1005-02A | Breather, rear axle differential | Nm | - | 30 | ||
| BA35.31-P-1006-02A | Bolt, side bearing cap to rear axle center assembly | Nm | - | - | ||
| BA35.31-P-1007-02A | Bolt, heat sink to end cover | Nm | 35 | - | ||
| BA35.31-P-1008-02A | Rear axle differential breather to end cover | Nm | 25 | - | ||
| BA35.31-P-1009-02A | Rear axle differential breather to rear axle housing | Nm | 30 | - | ||
| BA35.31-P-1010-02A | Locking bolt, vibration damper and rear axle housing to rear axle carrier | Stage 1 | Nm | - | - | |
| Stage 2 | ∠° | - | - | |||
| BA35.31-P-1011-02A | Oil temperature sensor for rear axle center assembly | Nm | - | - | ||
| BA35.31-P-1012-02A | Threaded insert to differential transmission housing | Nm | - | - | ||
| BA35.31-P-1013-02A | Fitting to threaded insert | Nm | - | - | ||
| BA35.31-P-1014-02A | Union nut, oil hose to fitting | Nm | - | - | ||
| BA35.31-P-1015-02A | Union nut for oil hose to oil pump | Nm | - | - | ||
| BA35.31-P-1016-02A | Banjo bolt for oil hose to oil pump | - | - | |||
| BA35.31-P-1017-02A | Banjo bolt, oil hose to threaded inserted | Nm | - | - | ||
| BA35.31-P-1018-02A | Banjo bolt for oil hose to oil cooler | Nm | - | - | ||
| BA35.31-P-1019-02A | Temperature switch to end cover for differential transmission | Nm | - | - | ||
REAR AXLE DIFFERENTIAL HOUSING
| Number | Designation | MODEL 220 | MODEL 230 except CODE P99 | |||
|---|---|---|---|---|---|---|
| BA35.31-P-1001-02A | Bolt, end cover to rear axle differential | Bolt+washer | Nm | - | - | |
| Flange bolt (TORX, internal serrations) | Stage 1 | Nm | 30 | 30 | ||
| Stage 2 | ∠° | 45 | 45 | |||
| BA35.31-P-1002-02A | Oil filler screw, differential | Nm | 50 | 50 | ||
| BA35.31-P-1003-02A | Oil drain screw for rear axle differential | Nm | 50 | 50 | ||
| BA35.31-P-1004-02A | Locking bolt, vibration damper and rear axle housing to rear axle carrier | Nm | - | - | ||
| BA35.31-P-1005-02A | Breather, rear axle differential | Nm | 30 | 30 | ||
| BA35.31-P-1006-02A | Bolt, side bearing cap to rear axle center assembly | Nm | - | - | ||
| BA35.31-P-1007-02A | Bolt, heat sink to end cover | Nm | - | 37 | ||
| BA35.31-P-1008-02A | Rear axle differential breather to end cover | Nm | - | - | ||
| BA35.31-P-1009-02A | Rear axle differential breather to rear axle housing | Nm | - | - | ||
| BA35.31-P-1010-02A | Locking bolt, vibration damper and rear axle housing to rear axle carrier | Stage 1 | Nm | - | - | |
| Stage 2 | ∠° | - | - | |||
| BA35.31-P-1011-02A | Oil temperature sensor for rear axle center assembly | Nm | - | - | ||
| BA35.31-P-1012-02A | Threaded insert to differential transmission housing | Nm | - | - | ||
| BA35.31-P-1013-02A | Fitting to threaded insert | Nm | - | - | ||
| BA35.31-P-1014-02A | Union nut, oil hose to fitting | Nm | - | - | ||
| BA35.31-P-1015-02A | Union nut for oil hose to oil pump | Nm | - | - | ||
| BA35.31-P-1016-02A | Banjo bolt for oil hose to oil pump | - | - | |||
| BA35.31-P-1017-02A | Banjo bolt, oil hose to threaded inserted | Nm | - | - | ||
| BA35.31-P-1018-02A | Banjo bolt for oil hose to oil cooler | Nm | - | - | ||
| BA35.31-P-1019-02A | Temperature switch to end cover for differential transmission | Nm | - | - | ||
REAR AXLE DIFFERENTIAL HOUSING
| Number | Designation | MODEL 230 with CODE P99 | MODEL 240 | |||
|---|---|---|---|---|---|---|
| BA35.31-P-1001-02A | Bolt, end cover to rear axle differential | Bolt+washer | Nm | - | - | |
| Flange bolt (TORX, internal serrations) | Stage 1 | Nm | 30 | 30 | ||
| Stage 2 | ∠° | 45 | 45 | |||
| BA35.31-P-1002-02A | Oil filler screw, differential | Nm | - | 50 | ||
| BA35.31-P-1003-02A | Oil drain screw for rear axle differential | Nm | - | 50 | ||
| BA35.31-P-1004-02A | Locking bolt, vibration damper and rear axle housing to rear axle carrier | Nm | - | - | ||
| BA35.31-P-1005-02A | Breather, rear axle differential | Nm | 30 | 25 | ||
| BA35.31-P-1006-02A | Bolt, side bearing cap to rear axle center assembly | Nm | - | - | ||
| BA35.31-P-1007-02A | Bolt, heat sink to end cover | Nm | - | - | ||
| BA35.31-P-1008-02A | Rear axle differential breather to end cover | Nm | - | - | ||
| BA35.31-P-1009-02A | Rear axle differential breather to rear axle housing | Nm | - | - | ||
| BA35.31-P-1010-02A | Locking bolt, vibration damper and rear axle housing to rear axle carrier | Stage 1 | Nm | - | - | |
| Stage 2 | ∠° | - | - | |||
| BA35.31-P-1011-02A | Oil temperature sensor for rear axle center assembly | Nm | - | - | ||
| BA35.31-P-1012-02A | Threaded insert to differential transmission housing | Nm | 50 | - | ||
| BA35.31-P-1013-02A | Fitting to threaded insert | Nm | 40 | - | ||
| BA35.31-P-1014-02A | Union nut, oil hose to fitting | Nm | 35 | - | ||
| BA35.31-P-1015-02A | Union nut for oil hose to oil pump | Nm | 35 | - | ||
| BA35.31-P-1016-02A | Banjo bolt for oil hose to oil pump | 25 | - | |||
| BA35.31-P-1017-02A | Banjo bolt, oil hose to threaded inserted | Nm | 25 | - | ||
| BA35.31-P-1018-02A | Banjo bolt for oil hose to oil cooler | Nm | 20 | - | ||
| BA35.31-P-1019-02A | Temperature switch to end cover for differential transmission | Nm | 30 | - | ||