Attach engine hoist - AR33.10-P-0105NKB

MODEL 117, 156, 176, 242, 246 

Shown on MODEL 246 with ENGINE 270 and TRANSMISSION 724 

Fig 1: Attaching Engine Hoist - Shown On Model 246 (1 Of 2)

Courtesy of MERCEDES-BENZ USA

Fig 2: Attaching Engine Hoist - Shown On Model 246 (2 Of 2)

Courtesy of MERCEDES-BENZ USA

Shown on MODEL 242 with ENGINE 780 

Fig 3: Attaching Engine Hoist - Shown On Model 242

Courtesy of MERCEDES-BENZ USA

	Risk of death  caused by vehicle slipping or toppling off of the lifting platform.	Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer.	AS00.00-Z-0010-01A
	Install/remove
1.1	Remove lower engine compartment paneling	Model 117, 176 with engine 133 Model 117, 176, 242, 246 with engine 270 Model 156
			AR61.20-P-1105NKB
1.2	Remove bottom section of soundproofing	Model 117, 176, 246 with engine 607, 651
			AR94.30-P-5300NKB
2	Remove front wheels	When removing the engine (1) and when removing the engine mounts.
			AP40.10-P-4050AK
3	Remove both front wheel housing covers	When removing the engine (1) and when removing the engine mounts.
			AR88.10-P-1300NKB
4	Remove electric vehicle sound generator (H4/16)	Model 242 with engine 780
5	Prepare support fixture (01)		AR33.10-P-0004-01NKB
		Model 117, 156, 176, 246 with engine 607 Adaptation	Fig 5
		Model 242 with engine 780 Adaptation	Fig 6
		Support fixture	Fig 4
6	Mount support fixture (01) on lifting platform (02)	When removing engine (1) and transmission (27)
	000 588 03 62 00 Lifting platform		WS01.00-P-0091A
7	Align support fixture (01) with lifting platform (02) under vehicle	When removing engine (1) and transmission (27)
8	Position support fixture (01) with lifting platform (02) under the engine (1) and the transmission (27)	When removing engine (1) and transmission (27)
9	Screw lock pins (31, 33) into supports on engine (1) and transmission (27)	Model 117, 156, 176, 246 Model 242 with engine 270 When removing engine (1) and transmission (27)
10.1	Mount supports (32, 34, 36) onto engine (1) and transmission (27)	Model 117, 156, 176, 246 Model 242 with engine 270 When removing engine (1) and transmission (27) The supports (32, 34, 36) and lock pins (31, 33) must be correctly positioned on engine (1) or transmission (27). Otherwise, damage will be caused to the oil pan or the transmission housing. The weight of the engine must not rest on the lock pins (31, 33), but must be distributed evenly onto the supports (32, 34, 36).
10.2	Mounts adaptations (37, 38) to engine (1) and transmission (27)	Model 242 with engine 780 When removing engine (1) and transmission (27) The adaptations (37, 38) must be fitted flush to the engine (1) and transmission (27). Otherwise the engine (1) or transmission housing may be damaged.
11	Secure engine (1) and transmission (27) to prevent them from falling down	When removing engine (1) and transmission (27)
12.1	Remove washer fluid reservoir of windscreen washer system	Model 117, 156, 176, 246 Model 242 with engine 270 When removing engine or transmission mount
			AR82.35-P-6000NKB
12.2	Detach washer fluid reservoir of windshield washer system and place to one side with lines connected.	Model 242 with engine 780 When removing engine or transmission mount
			AR82.35-P-6000NKB
13	Remove bolts securing front module to longitudinal members (2L, 2R)	When removing engine or transmission mount
			AR62.30-P-1570NKB
14	Unscrew bolt of the dampening on the longitudinal members (2L, 2R)	When removing engine or transmission mount
			AR62.30-P-1570NKB
15	Remove bolts securing radiator support (3L, 3R) to front axle carrier (4)	When removing engine or transmission mount
			AR62.30-P-1500NKB
16	Mount support (03) of support fixture (01) to longitudinal member (2L, 2R)	When removing engine or transmission mount
17	Mount support (03) of support fixture (01) to radiator support (3L, 3R)	When removing engine or transmission mount
18	Mount side carriers (04) of the support fixture (01) onto support (03)	When removing engine or transmission mount
19	Mount the base plate of the support fixture (01) onto the side carriers (04) of the support fixture (01)	When removing engine or transmission mount
20	Screw lock pins (31, 33) into supports on engine (1) and transmission (27)	Model 117, 156, 176, 246 Model 242 with engine 780 When removing engine or transmission mount
21.1	Mount supports (32, 34, 36) onto engine (1) and transmission (27)	Model 117, 156, 176, 246 Model 242 with engine 270 When removing engine or transmission mount
21.2	Mounts adaptations (37, 38) to engine (1) and transmission (27)	Model 242 with engine 780 When removing engine or transmission mount
22	Lift engine (1) and transmission (27) with support fixture (01) slightly	When removing engine or transmission mount
23	Mount supporting frame of support fixture (01) onto telescopic lifter	When removing and supporting front axle carrier (4)
	000 588 11 62 00 Major assembly mount		WS01.00-P-0092B
24	Position telescopic lifter using supporting frame under the vehicle and raise slightly	When removing and supporting front axle carrier (4) Ensure that the arresting pins (31, 33) fit cleanly into the openings in the front axle carrier (4) without damaging it.
25	Secure front axle carrier (4) against falling down	When removing and supporting front axle carrier (4)
26	Remove in the reverse order

Fig 4: Support Fixture (246 589 00 62 00)

Courtesy of MERCEDES-BENZ USA

Fig 5: Adaptation (607 589 00 31 00)

Courtesy of MERCEDES-BENZ USA

Fig 6: Adaptation (242 589 00 62 00)

Courtesy of MERCEDES-BENZ USA