Remove/install trunk lid - AR88.50-P-5000LW

MODEL 205.0/1 

Fig 1: Identifying Trunk Lid Remove/Install Components

Courtesy of MERCEDES-BENZ USA

Fig 2: Locating Left And Right Electrical Wiring Harness

Courtesy of MERCEDES-BENZ USA

Fig 3: Identifying Trunk Lid Remove/Install Components

Courtesy of MERCEDES-BENZ USA

	Risk of injury  caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.	No parts of the body or limbs should be within the operating area when the components are moving.	AS00.00-Z-0011-01A
	Information on preventing damage to electronic components due to electrostatic discharge		AH54.00-P-0001-01A
	Notes on sensor system for trunk lid opening/closing		AH80.61-P-0001-01A
	Remove
1	Open trunk lid (16)
2	Remove warning triangle (5) from warning triangle bracket
3	Remove hazard warning triangle bracket (5)
4	Remove hinge covers (2)
5	Unclip both retaining clips (3) on handle recess (4) and remove handle recess (4)	Clip remover	Figure
6	Unclip remaining retaining clips (3) and detach trunk lid paneling (1) until electrical connector (7) is accessible	Clip remover	Figure
7	Disconnect electrical connector (7) from ambient lamp and trunk lid warning lamp (6)
8	Remove trunk lid paneling (1)
9	Push back jacketing (9), disconnect electrical connector (10) an unclip left electrical wiring harness (8)	MODEL 205.0/1 with CODE 218 (Rear view camera) MODEL 205.0/1 with CODE 501 (360° camera)
10	Disconnect electrical connectors (12, 13, 14 and 15) and unclip right electrical wiring harness (11)	The number of electrical connectors (12, 13, 14 and 15) can vary depending on the equipment.
11	Remove screw/bolts (18)
12	Loosen screws/bolts (17)	Helper required to remove trunk lid (16).
13	Remove trunk lid (16) upward	Helper required to remove trunk lid (16).
	Install
14	Hook trunk lid (16) into hinges with bolts (17)	Screw in bolts (17) so that trunk lid (16) can still be moved. Tighten bolts (17) after adjusting trunk lid (16). Helper required to install trunk lid (16).
15	Screw in screws (18)	Screw in bolts (18) so that trunk lid (16) can still be moved. Tighten bolts (18) after adjusting trunk lid (16).
16	Clip in right electrical wiring harness (11) and connect electrical connectors (12, 13, 14 and 15)	The number of electrical connectors (12, 13, 14 and 15) can vary depending on the equipment.
17	Clip in left electrical wiring harness (8), connect electrical connector (10) and push jacketing (9) over electrical connector (10)	MODEL 205.0/1 with CODE 218 (Rear view camera) MODEL 205.0/1 with CODE 501 (360° camera)
18	Adjust trunk lid (16)		AR88.50-P-5200LW
19	Position trunk lid paneling (1) on trunk lid (16) and connect electrical connector (7) of ambient lamp and trunk lid warning lamp (6)
20	Fasten trunk lid paneling (1) with retaining clips (3)
21	Fasten handle recess (4) with both retaining clips (3)
22	Install hinge covers (2)
23	Install warning triangle bracket (5)
24	Insert warning triangle into warning triangle bracket (5)
25	Calibrate 360° camera with diagnostic system	MODEL 205.0/1 with CODE 501 (360° camera)
			AD00.00-P-2000-04B

Fig 4: Identifying Clip Remover (452 589 01 63 00)

Courtesy of MERCEDES-BENZ USA