Wiring Diagram For Adaptive Brake (ABR) - PE42.47-P-2000-97NBB
WARNING: This page does not describe the selected car, but rather 27 other vehicles, including the 2019 Mercedes-Benz GLE63 S AMG, 2019 Mercedes-Benz GLE63 AMG, 2019 Mercedes-Benz GLE43 AMG, 2019 Mercedes-Benz GLE400, and 2018 Mercedes-Benz GLE63 S AMG. However, it is still accessible from the selected car via links, so may be relevant.
MODEL 166.063 as of model year 2016 with CODE ME05 (HYBRID DRIVE 80KW VARIANT (INCLUDING PLUGIN)) Control unit N30/4
| Code: | Designation: | Position: |
|---|---|---|
| AO | Color code key | 72L |
| A7/7 | BAS brake booster | 57L |
| A7/7b1 | BAS diaphragm travel sensor | 55L |
| A7/7y1 | BAS solenoid valve | 56L |
| B18/5 | Brake pressure simulator valve pressure sensor | 62L |
| B24/15 | Yaw rate sensor for lateral and longitudinal acceleration | 24L |
| B37/1 | Pedal angle sensor | 47L |
| CAN E1 | Chassis CAN 1 | 13K |
| CAN H | Vehicle dynamics CAN | 20K |
| Code 233 | DISTRONIC PLUS | 19H |
| F32/3 | Engine compartment prefuse box | 4L |
| F32/3f1 | Fuse 1 | 2K |
| F58 | Engine compartment fuse and relay module | 8L |
| F58 | Engine compartment fuse and relay module | 34L |
| F58 | Engine compartment fuse and relay module | 43L |
| F58f201 | Fuse 201 | 42L |
| F58f204 | Fuse 204 | 7L |
| F58f230 | Fuse 230 | 8L |
| F58f236 | Fuse 236 | 33L |
| K109 | Vacuum pump relay (+) | 36L |
| K109/1 | Vacuum pump relay (-) | 40L |
| L6/1 | Left front axle rpm sensor | 53L |
| L6/2 | Right front axle rpm sensor | 51L |
| L6/3 | Left rear axle rpm sensor | 27L |
| L6/4 | Right rear axle rpm sensor | 29L |
| M56 | Vacuum pump | 38L |
| N10 | SAM control unit | 17L |
| N30/4 | Electronic Stability Program control unit | 12A |
| N30/4 | Electronic Stability Program control unit | 4A |
| N30/4 | Electronic Stability Program control unit | 20A |
| N30/4 | Electronic Stability Program control unit | 28A |
| N30/4 | Electronic Stability Program control unit | 37A |
| N30/4 | Electronic Stability Program control unit | 44A |
| N30/4 | Electronic Stability Program control unit | 52A |
| N30/4 | Electronic Stability Program control unit | 60A |
| N93/7 | Chassis gateway control unit | 20L |
| S9/1 | Stop lamp switch | 31L |
| U12 | Valid for left-hand drive vehicles | 45D |
| U12 | Valid for left-hand drive vehicles | 60D |
| U13 | Valid for right-hand drive vehicles | 47D |
| U13 | Valid for right-hand drive vehicles | 63D |
| W70 | ESP® ground point | 4E |
| W9 | Left front ground point (at lamp unit) | 41G |
| X25/2 | Engine compartment/vehicle interior electrical connector | 23G |
| X25/2 | Engine compartment/vehicle interior electrical connector | 25G |
| X25/2 | Engine compartment/vehicle interior electrical connector | 48F |
| X25/2 | Engine compartment/vehicle interior electrical connector | 64F |
| X30/19 | Vehicle floor chassis CAN E1 potential distributor electrical connector | 13L |
| X62/32 | Rear axle electrical connector, left distributor | 26J |
| X62/33 | Rear axle electrical connector, right distributor | 28J |
| X62/35 | BWI [BBV]/rpm left front axle electrical connector | 52G |
| X62/36 | BWI [BBV]/rpm right front axle electrical connector | 51G |
| Y113 | Brake pressure simulator valve | 64L |
| Z118/6 | Brake fluid check switch connector sleeve | 38E |