LEMON Manuals: Even more car manuals for everyone
Home >> Mercedes Benz >> 2014 >> GLK350 Base >> Repair and Diagnosis >> Electrical >> Motors, Switches, Relays >> Electrical System - Body - 204 Chassis - 1 Of 6 >> Basic Knowledge >> Headlamp control, function >> Headlamp control, function - GF82.10-P-2009CE

Headlamp control, function - GF82.10-P-2009CE

MODEL 204.0/2 except CODE (614) Bi-xenon headlamp unit except CODE (615) Bi-xenon headlamp unit with integrated curve illumination except CODE (616) Bi-xenon headlamp unit with integrated asymmetric curve illumination except CODE (618) Bi-xenon headlamps except CODE (621) Intelligent light system (left-hand traffic) except CODE (622) Intelligent light system (right-hand traffic) as of model year 2009/YoM 08 

MODEL 204.3 except CODE (615) Bi-xenon headlamp unit with integrated curve illumination except CODE (616) Bi-xenon headlamp unit with integrated asymmetric curve illumination except CODE (621) Intelligent Light System (left-hand traffic) except CODE (622) Intelligent Light System (right-hand traffic) 

MODEL 204.9 except CODE (615) Bi-xenon headlamp unit with integrated curve illumination except CODE (621) Intelligent Light System (left-hand traffic) except CODE (622) Intelligent Light System (right-hand traffic) 

Function requirements, general 

Driving lights actuation, general 

Driving lights actuation includes all functions which serve the optimum illumination of the road while driving.

During driving lights actuation, the standing lights actuation is active; this is described in the "Standing/parking lights actuation, function" document.

The driving lights actuation function is comprised of the following subfunctions:

IMPORTANT The driving lights are actuated corresponding to the position of the exterior lights switch (S1). The front SAM control unit with fuse and relay module (N10/1) directly reads in the status of the exterior lights switch for vehicles up to 31.5.10 over the instrument panel LIN (LIN 1) and for vehicles as of 1.6.10 (voltage-coded).

Additional low beams actuation function requirements 

IMPORTANT The electronic ignition lock control unit (N73) sends the status of circuit 15 to the front SAM control unit over the interior CAN (CAN B).

Function sequence for low beam actuation 

Turning the exterior lights switch to the "Manual driving lights" position requests actuation of the low beams.

The front SAM control unit reads in the status of the exterior lights switch and actuates the left low beam (E1e2) in the left front lamp unit (E1) and the right low beam (E2e2) in the right front lamp unit (E2). In addition, the front SAM control unit sends the request "Low beams indicator lamp On" via interior CAN to the instrument cluster (A1), which then actuates the low beams indicator lamp (A1e67).

Additional function requirements for high beam actuation 

IMPORTANT The electronic ignition lock control unit sends the status of circuit 15 to the front SAM control unit over the interior CAN.

Function sequence for high beam actuation 

The high beams actuation is comprised of the following subfunctions:

D Function sequence for high beams 

D Function sequence for headlamp flasher 

Function sequence for high beams 

High beam actuation is requested by pushing the combination switch (S4) forward.

The steering column tube module control unit (N80) directly reads in the position of the combination switch and transmits it to the front SAM control unit via the chassis CAN (CAN E).

The front SAM control unit receives the switch position of the combination switch, uses it to generate the "high beams ON" request and sends it over the interior CAN to the instrument cluster.

Finally the front SAM control unit in model 204 (except model 204.9 as of 1.6.12) actuates the left high beam (E1e1) and right high beam (E2e1). In model 204.9 as of 1.6.12 the front SAM control unit actuates the high beam in standing light and the left high beam (E1e21) and right high beam in standing light and the right high beam (E2e21). The instrument cluster actuates the high beams indicator lamp (A1e3).

IMPORTANT In model 204.9 as of 1.6.12 H15 lamps are installed, which are used for the standing light and high beam light functions.

Function sequence for headlamp flasher 

The function sequence and signal path for the headlamp flasher function correspond to that of the high beam function. However, to request the headlamp flasher function, the combination switch must be pulled backward. If the combination switch is pulled back and held, the high beam actuation is active for maximum t = 30 s. The permanently present request is then interpreted as a "stuck combination switch".

IMPORTANT In vehicles with code (460) Canada version or code (494) USA version, the high beams may not be actuated at the same time as the left front fog lamp (E5/1) and the right front fog lamp (E5/2). The last incoming request has priority.

In model 204.9 as of 1.6.12 front fog lamps are no longer installed.

Additional function requirements for daytime running lights actuation 

Function sequence for daytime running lights actuation 

The instrument cluster sends the request "Daytime running lights On" depending on the country coding or if the daytime running lights request was manually activated in the menu "Settings", "Light" via interior CAN.

The CDI control unit (N3/9) (with diesel engine) or the ME-SFI [ME] control unit (N3/10) (with gasoline engine) sends the "engine running" or "drivetrain ready" signal over the chassis CAN.

The instrument cluster sends the vehicle speed over the interior CAN.

The front SAM control unit reads in all relevant information, evaluates it and activates the daytime running lights actuation.

Daytime running lights actuation in model 204.0/2 up to 28.2.11, model 204.9 up to 31.5.12:

The front SAM control unit activates the low beams actuation and actuates the low beams.

IMPORTANT In vehicles with code (460) Canada version or code (494) USA version, the front SAM control unit activates the standing and/or low beams actuation as a function of the ambient brightness.

It is recorded by the light sensor (B38/1) (without code (345) Rain sensor) or by the rain/light sensor (B38/2) (with code (345) Rain sensor). The front SAM control unit reads in the data from the light sensor or the rain/light sensor via the wiper/inside rearview mirror LIN (LIN 2).

If the light sensor or the rain/light sensor recognizes that it is "day", the front SAM control unit actuates the low beams with reduced power (dimmed).

If the light sensor or the rain/light sensor recognizes that it is "dark", the front SAM control unit activates the standing and low beams actuation. The low beams are actuated with full power.

Daytime running lights actuation in model 204.0/2 as of 1.3.11, model 204.3, model 204.9 as of 1.6.12:

The front SAM control unit actuates the left daytime running lights headlamp (E1/3) and the right daytime running lights headlamp (E2/3).

In darkness the front SAM control unit also actuates the low beams.

The daytime running lights actuation is deactivated as soon as the exterior lights switch is turned to position "Standing lights", "Manual driving lights" or "Left parking light" or "Right parking light" (as of 1.6.10).

In vehicles with code (460) Canada version, the front SAM control unit terminates the daytime running lights actuation when the vehicle is at a standstill once a period of t = 3 minutes has expired. If the vehicle is then moved again, the front SAM control unit automatically activates the low beams actuation.

IMPORTANT The daytime running lights have a higher priority than the auto on/off headlamps.

In countries with legal daytime running light requirements, only the headlamp flasher is permissible but not the high beams.

The high beams are permissible only when the high beams are manually switched on via the exterior lights switch (without code (460) Canada version and without code (494) USA version).

Additional function requirements for auto on/off headlamps 

Function sequence for auto on/off headlamps 

The auto on/off headlamps function is no more than a comfort function and does not exempt the driver from following the rules in the road traffic regulations.

The CDI control unit or the ME-SFI [ME] control unit sends the "engine running" signal or the "drivetrain operational" signal over the chassis CAN to the front SAM control unit.

The instrument cluster sends the vehicle speed to the front SAM control unit over the interior CAN.

The front SAM control unit reads in the status of the exterior lights switch over the instrument panel LIN or directly, and the light sensor or rain/light sensor data over the wiper/inside rearview mirror LIN.

With the auto on/off headlamps, the low beams are automatically switched on or off.

This occurs depending on the ambient brightness or depending on the activities of the wiper system:

Function sequence for auto on/off headlamps via light sensor or rain/light sensor 

The light sensor or the rain/light sensor evaluates the ambient brightness. The front SAM control unit reads in the data of the light sensor or the rain/light sensor via wiper/inside rearview mirror LIN and activates the low beams actuation if darkness is recognized.

Function sequence for auto on/off headlamps via wiper activities 

If the low beams are switched on or off due to the activities of the wiper system, one refers to wiper, rain or adverse weather light. The front SAM control unit controls the wiper system and evaluates the data of the rain/light sensor or the wipe request via the combination switch for this.

If the windshield wiper system is activated for t = ≥ 20 s with a wipe cycle time of t < 6 s, the front SAM control unit activates low beam actuation. If there are no wipe cycles for t ≥ 60 s, low beams actuation is deactivated.

IMPORTANT Auto on/off headlamps switch-off conditions:

In the event of light sensor or rain/light sensor failure, the auto on/off headlamps are not deactivated until the engine is switched off. When the vehicle is being driven through a tunnel and if the wiper start suppression function is active, the auto on/off headlamps function remains switched on.

If the wiper startup suppression function is canceled, the auto on/off headlamps remain active for an additional t = 60 s.

Behavior of exterior lights with active auto on/off headlamps:     
Start of trip  Side lamp  Dipped beam 
Circuit 15C OFF Off Off
Circuit 15C ON Off Off
Circuit 15R ON On Off
Circuit 15 ON On Off
"Engine running" signal or
"Drivetrain ready" signal set or v > 3 km/h		 On On (high beams permissible)
End of trip  Side lamp  Dipped beam 
"Engine running" signal or
"Drivetrain ready" signal set or v > 3 km/h		 On On (high beams permissible)
Circuit 15 ON On Off
Circuit 15R ON On Off
Circuit 15C ON (driver door closed) On Off
Circuit 15C ON (driver door open) Off Off
Circuit 15C OFF Off Off

Additional function requirements for headlamp range adjustment 

Function sequence for headlamp range adjustment (HRA [LWR]) 

The headlamp range adjustment is installed as passive safety equipment in vehicles fitted with halogen headlamps to prevent them from causing glare to oncoming traffic. Depending on the load condition of the vehicle, the incline angle of the driving lights can be corrected by operating the headlamp range controller (S1s8).

The left headlamp range adjustment actuator motor (E1m1) and the right headlamp range adjustment actuator motor (E2m1) are actuated voltage-coded by the front SAM control unit in accordance with the position of the headlamp range adjuster. These then adjust the headlamp units in the front lamp units.

REFER TO SYSTEM WIRING DIAGRAMS Electrical function schematic for driving lights actuation Model 204.0/2/3,
Model 204.9 up to 31.5.12		 PE82.10-P-2059-97FAC
Model 204.9 as of 1.6.12 PE82.10-P-2059-97FAG
  Overview of exterior lights system components   GF82.10-P-9998CE 
scientia non olet · About LEMON Manuals