Retrofit reversing camera - AN54.65-P-0030SY

MODEL 221.0## (except 221.074/077) 1A as of 122604 up to 154194, 221.1## (except 221.174/176/177/179) 1A as of 122604 up to 154194 with CODE 808 (Model year 2008) without CODE 494 (US version) without CODE 498 (Japanese version) without CODE 806 (Model year 2006) without CODE 807 (Model year 2007) without CODE Z07 (Top protection) 

MODEL 221.0## (except 221.074/077) 1A as of 154195, 221.1## (except 221.174/176/177/179) 1A as of 154195 without CODE 494 (US version) without CODE 498 (Japanese version) without CODE Z07 (Top protection) 

Fig 1: Retrofitting Reversing Camera

Courtesy of MERCEDES-BENZ USA

	Information on preventing damage to electronic components due to electrostatic discharge		AH54.00-P-0001-01A
	Remove
1.1	Remove left rear seat backrest	MODEL 221.0/1 with CODE 223 (Rear bench seat with electrically adjustable outer seats with PRE-SAFE positioning function for outer seats and outer head restraints) or MODEL 221.1 with CODE 224 (Design individual rear seat system)
			AR91.12-P-1620SX
1.2	Remove rear seat backrest	MODEL 221.0/1 without CODE 223 (Rear bench seat with electrically adjustable outer seats with PRE-SAFE positioning function for outer seats and outer head restraints) and MODEL 221.1 without CODE 224 (Design individual rear seat system)
			AR91.12-P-1620SY
2	Remove left front seat
			AR91.10-P-1000SX
3	Disconnect battery ground line
			AR54.10-P-0003SX
4	Remove trims in trunk
			AR68.30-P-4600SX
		Except trim on right.
5	Detach rear SAM control unit with fuse and relay module (N10/2) and place to one side with electrical lines still connected
			AR54.21-P-1258SX
6	Detach overpressure reservoir and place to one side with electrical and pneumatic lines still connected	MODEL 221.0/1 with CODE 409 (Left/right front multicontour seats) or with CODE 432 (Left and right dynamic multicontour seat)
			AR91.25-P-1570SX
7	Remove cupholder	MODEL 221.0/1 with CODE 310 (Front double cup holder)
8	Remove COMAND controller unit (A40/3)
			AR82.85-P-1100SX
	Install
9	Retrofit reversing camera power supply module (N66/10)		AN54.65-P-0030-06SY
10	Retrofit reversing camera (B84/3)		AN54.65-P-0030-02SY
11	Retrofit reversing camera wiring harness (1)	MODEL 221.0/1 as of 154195 up to 31.05.09 up to model year 2009 MODEL 221.0/1 as of 122604 up to 154194 as of model year 2008	AN54.65-P-0030-03SY
		MODEL 221.0/1##1A as of 154195 as of model year 2010	AN54.65-P-0030-03SZ
		Wiring harness repair kit, basic	Figure
12	Install remaining parts
13	Connect Star Diagnosis
			AD00.00-P-2000-04A
14	Carry out variant coding with the Diagnosis Assistance System by means of Software Calibration Number (SCN)
15	Perform calibration of reversing camera (B84/3)	MODEL 221.0/1 up to 31.5.07
			AR54.65-P-0022SX
16	Enter special equipment in on-line vehicle data card via vehicle documentation system (VeDoc)	Add:  CODE 218 (Reversing camera)
17	Document retrofitted equipment through VeDoc	Attach a note "Reversing camera retrofitted as per AN54.65-P-0030SY " .
18	Disconnect Star Diagnosis
			AD00.00-P-2000-04A
	Check
19	Perform function test on reversing camera (B84/3)	The COMAND controller unit (A40/3) must be switched on.

Fig 2: Identifying Wiring Harness Repair Kit, Basic (000 589 13 99 00)

Courtesy of MERCEDES-BENZ USA