Check wiper arms and adjust - AR82.30-P-6000T

MODEL 211, 215, 220, 230, 231, 240 

MODEL 222 without CODE 874 (MAGIC VISION CONTROL, heated) 

Shown on MODEL 211, windshield wiper system in reversing position 

Fig 1: Checking Wiper Arms Distance - Shown On Model 211

Courtesy of MERCEDES-BENZ USA

	Injury hazard from pinching and crushing, in extreme cases extremities can even be cut off when caught in windshield wiper mechanism.	Always remove ignition key when working on windshield wiper mechanism.
	Check
1	Move windshield wiper system out of park position	To do this, turn on ignition (circuit 15 or circuit 15R) and move wiper switch to position "2". After windshield wiper system has left park position, turn off ignition and move wiper switch back to position "0".
2	Manually position windshield wiper system in reversing position	Distance between wiper blade on driver-side to A-pillar (A): Model 211, 215, 220, 230, 231 approx. 50 mm, MODEL 222 approx. 45 mm Model 240 approx. 70 mm. Distance between passenger-side wiper blade and A-pillar (B): MODEL 211 approx. 350 mm, MODEL 231 approx. 600 mm, in MODEL 215, 220, 222, 230, 240 distance between passenger-side wiper blade and A-pillar (B) results from distance between driver-side wiper blade and A-pillar (A). With left-hand drive vehicles, distance is measured from upper wiper blade ends of driver-side wiper arm (1) and passenger-side wiper arm (2) to inside of left A-pillar. With right-hand drive vehicles, distance is measured from upper wiper blade ends of driver-side wiper arm (1) and passenger-side wiper arm (2) to inside of right A-pillar.
3	Remove wiper blades	When working on raised driver-side wiper arm (1) or passenger-side wiper arm (2), ensure that they do not fall onto the windshield. Otherwise windshield will be damaged. See owner's manual.
4	Measure angle of incidence of driver-side wiper arm (1) and passenger-side wiper arm (2) in relation to windshield and record		AR82.30-P-6000-01T
		When changing from reversing position to park position, make sure that driver-side wiper arm (1) and passenger-side wiper arm (2) do not make direct contact with windshield. Otherwise, the windshield may be scratched. Cover driver-side wiper arm (1) and passenger-side wiper arm (2) with appropriate means (scratch protection).
		Adjusting tool set	Figure
5	Compare test values with adjustment values and select correct adjustment measure
	Notes on wiper arm adjustment
		MODEL 222 without CODE 874 (MAGIC VISION CONTROL, heated)	*BE82.30-P-1001-01M
		MODEL 222 without CODE 874 (MAGIC VISION CONTROL, heated)	*BE82.30-P-1002-01M
		MODEL 222 without CODE 874 (MAGIC VISION CONTROL, heated)	*BE82.30-P-1003-01M
		MODEL 222 without CODE 874 (MAGIC VISION CONTROL, heated)	*BE82.30-P-1004-01M
		MODEL 211, 215, 220, 230, 240	*BE82.30-P-1001-01E
		MODEL 211, 215, 220, 230, 240	*BE82.30-P-1002-01E
		MODEL 211, 215, 220, 230, 240	*BE82.30-P-1003-01E
		MODEL 211, 215, 220, 230, 240	*BE82.30-P-1004-01E
		MODEL 231	*BE82.30-P-1001-01L
		MODEL 231	*BE82.30-P-1002-01L
		MODEL 231	*BE82.30-P-1003-01L
		MODEL 231	*BE82.30-P-1004-01L
6	Adjust angle of incidence of driver-side wiper arm (1) or front passenger side wiper arm (2) in park position	In the event that the test values deviate from the tolerance range in reversing position or in parked position and reversing position.
		Distort driver-side wiper arm (1) or front passenger side wiper arm (2) by at least the value of the tolerance deviation in reversing position.	AR82.30-P-6100-01T
		MODEL 222 without CODE 874 (MAGIC VISION CONTROL, heated)	*BE82.30-P-1003-01M
		MODEL 222 without CODE 874 (MAGIC VISION CONTROL, heated)	*BE82.30-P-1004-01M
		MODEL 211, 215, 220, 230, 240	*BE82.30-P-1003-01E
		MODEL 211, 215, 220, 230, 240	*BE82.30-P-1004-01E
		MODEL 231	*BE82.30-P-1003-01L
		MODEL 231	*BE82.30-P-1004-01L
		Adjusting tool set	Figure
7	Adjust windshield wiper system	In the event that check values of the driver-side wiper arm (1) and passenger-side wiper arm (2) deviate from tolerance range in park position.
		Remove/install wiper system MODEL 231	AR82.30-P-6400RK
		MODEL 211	AR82.30-P-6400-01T
		MODEL 215, 220	AR82.30-P-6400-01M
		MODEL 222 without CODE 874 (MAGIC VISION CONTROL, heated)	AR82.30-P-6400-01CW
		MODEL 230	AR82.30-P-6400-01R
		MODEL 240	AR82.30-P-6400-01H
		MODEL 222 without CODE 874 (MAGIC VISION CONTROL, heated)	*BE82.30-P-1003-01M
		MODEL 222 without CODE 874 (MAGIC VISION CONTROL, heated)	*BE82.30-P-1004-01M
		MODEL 211, 215, 220, 230, 240	*BE82.30-P-1003-01E
		MODEL 211, 215, 220, 230, 240	*BE82.30-P-1004-01E
		MODEL 222 without CODE 874 (MAGIC VISION CONTROL, heated)	*BA82.30-P-1001-01P
		MODEL 215, 220, 230	*BA82.30-P-1005-01A
		MODEL 211.0/2/6, 230, 240	*BA82.30-P-1007-01A
		Adapter	Fig 2
		Mounting wedge	Figure
		Extraction hook	Fig 4
		MODEL 231 Adjusting tool set	Figure
8	Cover driver-side wiper arm (1) and passenger-side wiper arm (2) using suitable aids and move windshield wiper system out of park position	When moving windshield wiper system out of park position, ensure that driver-side wiper arm (1) and passenger-side wiper arm (2) do not make direct contact with windshield. Otherwise, the windshield may be scratched. To do this, turn on ignition (circuit 15 or circuit 15R) and move wiper switch to position "2". After windshield wiper system has left park position, turn off ignition and move wiper switch back to position "0".
9	Install wiper blades	When working on raised driver-side wiper arm (1) or passenger-side wiper arm (2), ensure that they do not fall onto the windshield. Otherwise windshield will be damaged. See owner's manual.
10	Perform function check on windshield wiper system

Fig 2: Identifying Adapter (231 589 00 21 00)

Courtesy of MERCEDES-BENZ USA

Fig 3: Identifying Mounting Wedge (110 589 03 59 00)

Courtesy of MERCEDES-BENZ USA

Fig 4: Identifying Extraction Hook (140 589 02 33 00)

Courtesy of MERCEDES-BENZ USA

Fig 5: Identifying Adjusting Tool Set (211 589 02 21 00)

Courtesy of MERCEDES-BENZ USA