Remove/install brake hoses at front axle - AR42.10-P-0024GW

MODEL 463 as of model year 2013 

Shown on MODEL 463 as of model year 2013 

Fig 1: Front Axle Brake Hoses Remove/Install Components - Model 463 As Of Model Year 2013 (1 Of 2)

Courtesy of MERCEDES-BENZ USA

Fig 2: Front Axle Brake Hoses Remove/Install Components - Model 463 As Of Model Year 2013 (2 Of 2)

Courtesy of MERCEDES-BENZ USA

Shown on MODEL 463 as of model year 2016 

Fig 3: Front Axle Brake Hoses Remove/Install Components - Model 463 As Of Model Year 2016

Courtesy of MERCEDES-BENZ USA

	Risk of poisoning  from swallowing brake fluid. Risk of injury  from skin and eye contact with brake fluid	Only pour brake fluid into suitable and appropriately marked containers. Wear protective clothing and eye protection when handling brake fluid.	AS42.50-Z-0001-01A
	Risk of accident  when commissioning the vehicle due to a lack of braking effect when the service brake is operated for the first time after repair work.	Before starting the engine, actuate brake pedal several times until pressure is built up and maintained in the brake system.	AS42.50-Z-0002-01A
	Brake fluid notes		AH42.50-P-0001-01A
	Notes on repairs to brake system		AH42.00-P-0003-01A
	Remove/install
1	Remove front wheel-and-tire assemblies
			AP40.10-P-4050G
	Clean
2	Clean area surrounding connecting points to be opened on the brake system	Before opening the brake system the area around the separation point should be cleaned thoroughly. Even the smallest particles of dirt, introduced into the hydraulic components, can lead to malfunctions and a total failure of the brake system. Only use clean, lint free rags and cleaner free of mineral oil. Do not use any compressed- air for cleaning when the brake system is open.
3.1	Detach brake hose (1) from brake hose (2)	Model 463 as of model year 2013 up to model year 2016 It must be ensured that the components are installed so that they do not chafe against other components and that they are not subject to torsion.
		Brake line to front-axle brake hose	*BA42.10-P-1008-04B
3.2	Detach brake hose (2) from brake line (10)	Model 463 as of model year 2016 It must be ensured that the components are installed so that they do not chafe against other components and that they are not subject to torsion.
		Brake line to brake hose	*BA42.10-P-1001-04B
4	Collect any escaping brake fluid using a suitable container
5	Seal exposed connections with plugs	Record plug	Figure
6	Detach cable tie (4) from brake hose (1)	Model 463 as of model year 2013 up to model year 2016 Replace cable tie (4).
7	Detach brake hose (1) from brake caliper (3)	Model 463 as of model year 2013 up to model year 2016 It must be ensured that the components are installed so that they do not chafe against other components and that they are not subject to torsion.
		Brake line to fixed brake caliper	*BA42.10-P-1002-04B
8	Collect any escaping brake fluid using a suitable container	Model 463 as of model year 2013 up to model year 2016
9	Seal exposed connections with plugs	Model 463 as of model year 2013 up to model year 2016
		Record plug	Figure
10	Detach clamp (5) from brake hose (2)	It must be ensured that the clamp (5) is seated correctly.
11	Pull brake hose (2) out of rubber spacer (7)
12	Detach brake hose (2) from brake line (6)	It must be ensured that the components are installed so that they do not chafe against other components and that they are not subject to torsion.
		Brake line to brake hose	*BA42.10-P-1001-04B
13	Collect any escaping brake fluid using a suitable container
14	Seal exposed connections with plugs	Record plug	Figure
15	Remove clamp (8) from brake hose (2)	It must be ensured that the clamp (8) is seated correctly.
16	Install in the reverse order
17	Bleed brake system		AR42.10-P-0010GW

Fig 4: Identifying Record Plug (129 589 00 91 00)

Courtesy of MERCEDES-BENZ USA