Remove/install front seat - AR91.10-P-1000SC
MODEL 216.3
Shown on left front seat (1)
MODIFICATION NOTES
| 22.4.08 | Parameterize weight sensing system (WSS) with STAR DIAGNOSIS added | Step 33 |
| Removing | |||
| Risk of injury caused by performing testing or repair work on airbag or emergency tensioning retractor units. | Store airbag units with deployment side facing up; do not expose to temperatures greater than 100 °C. When working on these units, disconnect the power supply. | AS91.00-Z-0001-01A | |
| Notes on performing repair, body work and welding on vehicles with airbags or emergency tensioning retractor units | AH91.00-P-0002-01M | ||
| Information on preventing damage to electronic components due to electrostatic discharge | AH54.00-P-0001-01A | ||
| Assessment of airbag and emergency tensioning retractor units in accident vehicles | AH91.00-P-0006-01B | ||
| Legal requirements on handling and storing airbags and emergency tensioning retractor units | AH91.00-P-0004-01A | ||
| 1 | Unclip left or right door sill molding (2) | Fig 2 | |
| 2 | Fold backrest of front seat (1) toward the front | ||
| 3 | Unclip covers (6, 9) | Fig 2 | |
| 4 | Remove bolts (7, 8) | ||
| 5 | Move front seat (1) all the way back and to the rear | ||
| 6 | Unclip cover (3) | Fig 2 | |
| 7 | Unscrew bolts (4, 5) | ||
| 8 | Disconnect battery ground line | AR54.10-P-0003SX | |
| 9 | Tilt back front seat (1) | ||
| 10 | Disconnect electrical connector (10) | ||
| 11 | Disconnect electrical connector (12) on left front seat control unit (N32/1) or right front seat control unit (N32/2) | ||
| 12 | Detach pneumatic line (11) | ||
| 13 | Carefully remove front seat (1) from vehicle | ||
| Install | |||
| 14 | Carefully insert front seat (1) into the vehicle and tilt back | ||
| 15 | Connect electrical connector (10) | ||
| 16 | Connect electrical connector (12) on left front seat control unit (N32/1) or right front seat control unit (N32/2) | ||
| 17 | Connect pneumatic line (11) | ||
| 18 | Carefully tilt front seat (1) toward front | ||
| 19 | Connect ground cable to battery | AR54.10-P-0003SX | |
| 20 | Screw in bolts (4, 5) up to contact surface, do not tighten | ||
| 21 | Move front seat (1) all the way to the front | ||
| 22 | Screw in bolts (7, 8) up to contact surface, do not tighten | ||
| 23 | Move front seat (1) all the way back | ||
| 24 | Tighten bolt (5) | *BA91.10-P-1002-01O | |
| 25 | Move front seat (1) all the way to the front | ||
| 26 | Tighten bolts (7) | *BA91.10-P-1002-01O | |
| 27 | Tighten bolt (8) | *BA91.10-P-1002-01O | |
| 28 | Clip in covers (6, 9) | ||
| 29 | Move front seat (1) all the way back | ||
| 30 | Tighten screw (4) | *BA91.10-P-1002-01O | |
| 31 | Clip in cover (3) | ||
| 32 | Clip in door sill molding (2) | ||
| 33 | Parameterize weight sensing system (WSS) with STAR DIAGNOSIS | After installing the front passenger seat on vehicles with code (494) USA version. |
|
| Fig 3 | |||
| Connect STAR DIAGNOSIS and read out fault memory | AD00.00-P-2000-04A |
FRONT SEATS
| Number | Designation | Model 216 | |
|---|---|---|---|
| BA91.10-P-1002-01O | Seat bolt to vehicle floor | Nm | 53 |