Overview of wiring diagrams for electrical system, equipment and instruments - PE54.00-P-1100FAA
MODEL 204
| Wiring diagram control unit DC/AC converter | MODEL 204.0 as of model year 2011 with CODE 460 (Canada version) with CODE 494 (US version) with CODE U80 (115 V socket in load compartment) Control unit N24/3MODEL 204.9 with CODE 460 (Canada version) with CODE 494 (US version) with CODE U80 (115 V socket in load compartment) Control unit N24/3 | PE54.10-P-2103FAA | |
| Wiring diagram of interior fuse box (F34) | MODEL 204.0/2/3 as of model year 2013MODEL 204 up to model year 2010 | PE54.15-P-2501FAA | |
| Wiring diagram of front backup fuse box (F32) | MODEL 204 up to model year 2009 | PE54.15-P-2502FAA | |
| MODEL 204 as of model year 2010 without CODE B03 (ECO start/stop function) | PE54.15-P-2502FAB | ||
| MODEL 204 as of model year 2010 with CODE B03 (ECO start/stop function) | PE54.15-P-2502FAC | ||
| Wiring diagram, rear prefuse box (F33) | MODEL 204 | PE54.15-P-2503FAA | |
| Connector separation point wiring diagram | MODEL 204X8/4, X8/19, X18, X18/2, model 1 | PE54.18-P-2300FAA | |
| MODEL 204 with ENGINE 156, 271, 272, 646, 651X26, model 2 | PE54.18-P-2300FAB | ||
| MODEL 204X1/45, X8/34, X8/35, X35/1, X35/2, X62/6, X62/7, X62/32, X62/33, model 3 | PE54.18-P-2300FAC | ||
| MODEL 204X8/36, X35/3, model 4 | PE54.18-P-2300FAD | ||
| MODEL 204X25/4 (M271, M272), X25/12 (M642), X35/6 (M642, M271, M272), X86/2 (M272), X220 (M271KE), model 5 | PE54.18-P-2300FAE | ||
| MODEL 204X28/18, X55/3, X55/4, X150/1, X150/2, X173/1, X173/2, model 6 | PE54.18-P-2300FAF | ||
| MODEL 204 with ENGINE 642.8/9X26 (M642), X35/6 (M642), model 7 | PE54.18-P-2300FAG | ||
| MODEL 204X8/37, X35/4, X35/28, model 8 | PE54.18-P-2300FAH | ||
| MODEL 204X26 (M651), X26/7 (M651), X35/6 (M651), X220 (M651), model 9 | PE54.18-P-2300FAI | ||
| MODEL 204X26/38, X25/4 (M156), X35/6 (M156), model 10 | PE54.18-P-2300FAJ | ||
| MODEL 204X25/4 (M276), X26 (M276), X35/6 (M276), X86/3 (M276), X86/4 (M276), model 11 | PE54.18-P-2300FAK | ||
| Wiring diagram for electronic ignition switch (EIS) control unit | MODEL 204Control unit N73 | PE54.21-P-2104FAA | |
| Wiring diagram, special vehicle multifunction control unit (SVMCU (MSS)) | MODEL 204.0/2 with CODE 965 (Electrical preinstallation, rental vehicles) Control unit N26/9 | PE54.21-P-2105FAA | |
| Wiring diagram of front SAM control unit with fuse and relay module (N10/1) | MODEL 204.0/2/3/9model 1 | PE54.21-P-2106FAA | |
| model 2 | PE54.21-P-2106FAB | ||
| MODEL 204.0/2/3/9model 3 | PE54.21-P-2106FAC | ||
| MODEL 204.0/2/3/9model 4 | PE54.21-P-2106FAD | ||
| MODEL 204.0/2/3/9model 5 | PE54.21-P-2106FAE | ||
| MODEL 204.0/2/3/9model 6 | PE54.21-P-2106FAF | ||
| MODEL 204.0/2/3/9model 7 | PE54.21-P-2106FAG | ||
| MODEL 204.0/2/3/9model 8 | PE54.21-P-2106FAH | ||
| MODEL 204.0/2/3/9model 9 | PE54.21-P-2106FAI | ||
| Wiring diagram for overhead control panel (OCP) control unit | MODEL 204.0/2 with CODE 414 (Electric sunroof, glass version) Control unit N70 | PE54.21-P-2107FAA | |
| MODEL 204.0/2/3/9 without CODE 414 (Electric sunroof, glass version) Control unit N70/3 (without CAN) | PE54.21-P-2107FAB | ||
| Wiring diagram/rear SAM control unit with fuse and relay module (N10/2) | MODEL 204.0/2/3/9model 1 | PE54.21-P-2108FAA | |
| model 2 | PE54.21-P-2108FAB | ||
| MODEL 204.0/2/3/9model 3 | PE54.21-P-2108FAC | ||
| MODEL 204.0/2/3/9model 4 | PE54.21-P-2108FAD | ||
| MODEL 204.0/2/3/9model 5 | PE54.21-P-2108FAE | ||
| MODEL 204.0/2/3/9model 6 | PE54.21-P-2108FAF | ||
| MODEL 204.0/2/3/9model 7 | PE54.21-P-2108FAG | ||
| MODEL 204.0/2/3/9model 8 | PE54.21-P-2108FAH | ||
| Wiring diagram for sound generator control unit | MODEL 204.3Control unit N12 | PE54.21-P-2115FAA | |
| Wiring diagram for upper control panel control unit | MODEL 204.0/2/3/9Control unit N72/1 | PE54.21-P-2119FAA | |
| Wiring diagram for drive unit control unit | MODEL 204.077/277/377 with ENGINE 156Control unit N145 | PE54.21-P-2128FAA | |
| Wiring diagram for multifunction camera | MODEL 204 as of model year 2012 with CODE 238 (Active lane keeping Assist) with CODE 476 (Automatic lane recognition) with CODE 513 (Speed Limit Assist) with CODE 608 (Adaptive Highbeam Assist) Control unit A40/11 | PE54.21-P-2129FAA | |
| Wiring diagram for data link connector/diagnostic socket | MODEL 204.0/2/3/9Test connector X11/4 | PE54.22-P-2000FAA | |
| Wiring diagram for instrument cluster (IC) control unit | MODEL 204.0/2/3/9Control unit A1 | PE54.30-P-2101FAA | |
| Wiring diagram for Parktronic system (PTS) control unit | MODEL 204.9 with CODE 220 (PARKTRONIC) Control unit N62MODEL 204.0/2 up to model year 2011 with CODE 220 (PARKTRONIC) Control unit N62MODEL 204.0/2 as of model year 2012 with CODE 230 (Advanced Parking Guidance) Control unit N62MODEL 204.3 with CODE 230 (Advanced Parking Guidance) Control unit N62 | PE54.65-P-2101FAA | |
| Wiring diagram for backup camera control unit | MODEL 204.0/2/3/9 with CODE 218 (Rear view camera) with CODE 498 (Japanese version) Control unit N66/2 | PE54.65-P-2102FAA | |
| MODEL 204.0/2/3/9 with CODE 218 (Rear view camera) without CODE 498 (Japanese version) Control unit N66/10 | PE54.65-P-2102FAB | ||
| Wiring diagram of reversing camera | MODEL 204.9 as of model year 2013 with CODE 218 (Rear view camera) without CODE 498 (Japanese version) Control unit B84/3 | PE54.65-P-2103FAA | |
| MODEL 204.9 as of model year 2013 with CODE 218 (Rear view camera) with CODE 498 (Japanese version) Control units N93/3 and B84/3 | PE54.65-P-2103FAB | ||
| Wiring diagram for 360° camera control unit | MODEL 204.9 as of model year 2013 with CODE 501 (360 degree camera) Control unit N148 | PE54.65-P-2104FAA | |
| Blind Spot Assist wiring diagram | MODEL 204.0/2/3 with CODE 234 (Blind Spot Monitoring) with CODE 476 (Automatic lane recognition) MODEL 204.9 as of model year 2013 with CODE 234 (Blind Spot Monitoring) with CODE 476 (Automatic lane recognition) | PE54.71-P-2100FAA |