Remove/install front bumper - AR88.20-P-2000EL
MODEL 218
Shown up to model year 2015
Shown up to model year 2015
Shown up to model year 2015
| General information on the impact absorber | AH88.20-P-1000-01A | ||
| Remove/install | |||
| Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. | AS00.00-Z-0010-01A | |
| 1 | Lift vehicle on vehicle lift | ||
| 2.1 | Remove front engine compartment paneling | MODEL 218 with ENGINE 157 MODEL 218 with ENGINE 274 MODEL 218 with ENGINE 276 MODEL 218 with ENGINE 278 |
|
| AR61.20-P-1105EW | |||
| 2.2 | Remove bottom section of soundproofing | MODEL 218 with ENGINE 642 MODEL 218 with ENGINE 651 |
|
| AR94.30-P-5300EW | |||
| 3 | Unscrew bolt (10) from left bracket (11) | ||
| 4 | Unscrew bolt (8) from right bracket (9) | ||
| 5 | Detach bumper (1) from right bracket (9) and left bracket (11) | ||
| 6 | Loosen left fender liner front section (4) in area of bumper (1) and remove | Fig 7 | |
| 7 | Detach right fender liner front section (7) in area of bumper (1) and remove | Fig 7 | |
| 8 | Unscrew bolts (3) from left front fender (2) | Tighten bolts (3, 6) after adjusting gap dimensions on bumper (1). Before tightening bolts (3, 6): ↓ Adjust gap dimensions on bumper (1). |
|
| Gap dimensions on hoods, doors and lids | AR60.00-P-0700-01EL | ||
| Gap dimension | *BE60.00-P-1001-01O | ||
| Figure | |||
| 9 | Unscrew bolts (6) on right front fender (5) | ||
| 10 | Disconnect electrical connector on frame wiring harness and front bumper (X2638) | MODEL 218 with CODE 220 (PARKTRONIC) MODEL 218 with CODE 233 (DISTRONIC PLUS) MODEL 218 with CODE 235 (Active Parking Assist) MODEL 218 with CODE 237 (Active Blind Spot Assist) |
|
| 11 | Disconnect electrical connector from front 360° camera | MODEL 218 as of model year 2015 with CODE 501 (360 degree camera) |
|
| 12 | Disconnect electrical connector (12) from left daytime running lamp headlamp (E1/3) | MODEL 218 up to model year 2015 without CODE 498 (Japanese version) |
|
| 13 | Disconnect electrical connector (13) from left daytime running lamp headlamp (E2/3) | MODEL 218 up to model year 2015 without CODE 498 (Japanese version) |
|
| 14 | Detach bumper (1) from left front fender (2) and right front fender (5) | ||
| 15 | Detach catch hooks (19) from mounting rail (18) successively starting at one side | ||
| Fig 6 | |||
| 16 | Remove bumper (1) toward front | ||
| 17 | Disassemble front bumper (1) | Only when replacing bumper (1). | |
| 18 | Install in the reverse order | ||
| 19 | Calibrate front 360° camera (B84/9) using diagnostic system | MODEL 218 with CODE 501 (360 degree camera) |
|
| AD00.00-P-2000-04A |
TEST VALUES FOR GAP DIMENSIONS ON HOODS, DOORS AND LIDS
| Number | Designation | MODEL 218.9 | MODEL 218.3 | |||
|---|---|---|---|---|---|---|
| BE60.00-P-1001-01O | Gap dimension | Engine hood to fender | Dimension "A" | mm | 4, 0 (±1) | 4, 0 (±1) |
| Engine hood to headlamp | Dimension "B" | mm | 4, 0 (±1) | 4, 0 (±1) | ||
| Engine hood to bumper | Dimension "C" | mm | 4, 0 (±1) | 4, 0 (±1) | ||
| Engine hood to A-pillar | Dimension "Q" | mm | 4, 5 (±1) | 4, 5 (±1) | ||
| Fender to headlamp | Dimension "R" | mm | 4, 0 (±1) | 4, 0 (±1) | ||
| Bumper to headlamp (circumferential) | Dimension "S" | mm | 3, 5 (±1) | 3, 5 (±1) | ||
| Mounting rail, bumper to engine hood | Dimension "T" | mm | 7, 5 (+0, 5) | 7, 5 (+0, 5) | ||
| Mounting rail, bumper to engine hood | Dimension "U" | mm | 1, 0 (±0, 5) | 1, 0 (±0, 5) | ||