Remove/install parking brake pedal assembly - AR42.20-P-0510GZ
MODEL 164
Shown on model 164.1
| Removing | |||
|---|---|---|---|
| 1 | Remove footwell paneling (1) | AR68.30-P-4010GZ | |
| Fig 4 | |||
| 2 | Undo bolts (5) and bolt (7) and fold cover under instrument panel (6) with air duct (9) downwards | ||
| 3 | Release plug (11) and detach from data link connector (X11/4) and then unplug electrical connector (10) | ||
| 4 | Thread hood release (8) out of covering under the instrument panel (6) and remove covering under the instrument panel (6) together with the air duct (9) | ||
| 5 | Pull out release (2) and remove both bolts concealed behind it | ||
| 6 | Pull out internal component of release (4) together with release cable (3), until the cable's ball head is accessible | ||
| 7 | Unhook ball head on internal component of release (4), remove release (2) and internal component of release (4) | ||
| 8 | Detach plug (13) on parking brake indicator switch (S12) and unclip securing clip (18) using suitable tool | ||
| 9 | Release notch (16) using suitable tool and thread notched rail (17) towards rear and out of the parking brake pedal assembly (12) | ||
| 10 | Undo bolt (14, 15) and remove parking brake pedal assembly (12) with release cable (3) | ||
| Notes on self-locking nuts and bolts | All models | AH00.00-N-0001-01A | |
| 11 | Unhook release cable (3) on parking brake pedal assembly (12), unclip plastic clip and remove release cable (3) | Fig 5 | |
| Install | |||
| 12 | Clip plastic clip on release cable (3) into parking brake pedal assembly (12) and hook release cable (3) onto parking brake pedal assembly (12) | ||
| 13 | Position parking brake pedal assembly (12) and turn in bolt (14, 15) | *BA42.20-P-1001-01I | |
| Notes on self-locking nuts and bolts | All models | AH00.00-N-0001-01A | |
| 14 | Thread notched rail (17) into parking brake pedal assembly (12) and allow to latch into first notch (16) | ||
| 15 | Clip securing clip (18) into place | ||
| 16 | Connect plug (13) onto parking brake indicator switch (S12) | ||
| 17 | Route release cable (3) behind paneling upwards and hook ball head of cable in internal component of release (4) | ||
| 18 | Fasten internal component of release (4) with pulled release (2) using the two bolts | ||
| 19 | Engage and disengage the parking brake several times in succession | ||
| Risk of death caused by body parts being pulled in by rotating vehicle wheels and roller dynamometer rollers | Do not insert your hand into rotating parts. Wear closed and snug-fitting work clothes. Safeguard areas with rotating vehicle parts and dynamometer rollers against unauthorized access. Safeguard roller dynamometer from unauthorized access. |
AS00.00-Z-0019-01A | |
| 20 | Test parking brake | ||
| Brake testing on test stand | AP42.00-P-4290GZ | ||
| 21 | Mount footwell paneling (1) | ||
| 22 | Thread hood release (8) into covering under the instrument panel (6) and fasten in place using bolt (7) | ||
| 23 | Fit plug (11) onto data link connector (X11/4) and join with connector (10) | ||
| 24 | Insert covering under instrument panel (6) at rear into corresponding fixtures, fold the covering under the instrument panel (6) upwards and fasten in place using bolts (5) |
PARKING BRAKE
| Number | Designation | Model 164.1/8 | |
|---|---|---|---|
| BA42.20-P-1001-01I | Bolt for pedal assembly of parking brake to A-pillar | Nm | 20 |