Instrument cluster (IC), operating information - GF54.30-P-0002-05GM

Operating instructions 

Various menu levels can be displayed in the multifunction display (A1p13) of the instrument cluster (A1) using the left multifunction steering wheel button group (S110) and right multifunction steering wheel button group (S111):

• It is possible to scroll between the respective menus and submenus (S110s1) or in various lists via the scroll forward and back button.
• The system selection button (S110s3) can be used to change from each menu and submenu into the next higher menu level.
• The + and - adjustment of specific functions and volume control (S111s1) button can be used to confirm each selection or pending messages.

All the buttons of the multifunction steering wheel button group are always fitted. The activation of the corresponding functions however depends on the equipment fitted.

Overview of available menus (equipment-dependent):

• Basic menu 
• "Audio" menu 
• "Navigation" menu (with code (511) Audio 50 APS incl. DVD changer or code (525) MB Audio 50 APS radio or code (512) COMAND APS with DVD changer or code (527) COMAND APS with single DVD drive (with navigation) or code (528) COMAND incl. DVD changer) 
• "Offroad" menu (with model 164 with code (430) Offroad package) 
• "Distronic" menu (with code (219) DISTRONIC) 
• System state and fault messages menu 
• Set up menu 
• Trip computer menu 
• "Telephone" menu (with code (386) Mobile phone) 
• "Workshop level" menu 

Basic menu 

The following information can be called up in the basic menu:

• Trip and main odometer
• Check engine oil level
• Service indicator
• Current vehicle speed
• Coolant temperature
• Tire pressure monitor (with code (470) Tire pressure monitor (basis) or with code (475) Tire pressure monitor (premium))

"Audio" menu 

The following information can be displayed in the Audio menu:

• Current radio frequency adjusted
• Selected music track or CD track

"Navigation" menu (with code (511) Audio 50 APS incl. DVD changer or code (525) MB Audio 50 APS radio or code (512) COMAND APS with DVD changer or code (527) COMAND APS with single DVD drive (with navigation) or code (528) COMAND incl. DVD changer) 

The "Navigation" menu can be used to activate or deactivate the navigation function. Navigation information is displayed when the system is active. "NAV OFF" is shown when the system is deactivated.

"Offroad" menu (with model 164 with code (430) Offroad package) 

The "Offroad" menu displays the compass data. Depending on the vehicle equipment with code (430) Off-road package displays the current condition of the differential lock and rear axle differential lock and with code (489) AIRmatic (air suspension with level adjustment and adaptive damping system (ADS)) the AIRmatic status is shown.

"Distronic" menu (with code (219) DISTRONIC) 

When the Distronic function is activated, the "Distronic" menu displays a tracking graphic in which one's own vehicle is always shown on the right edge of the multifunction display.

System state and fault messages menu 

The system state and fault messages menu shows the number of fault messages stored in the memory.

Individual messages can then be displayed using the scroll forwards and back button.

Set up menu 

In the "Settings" menu the following submenus are displayed in which various adjustments can be performed:

• "Instrument cluster" (e.g. language)
• "Illumination" (e.g. interior lights OFF delay time)
• "Vehicle" (e.g. automatic door locking)
• "Heater" (e.g. cut-in time)
• "Comfort" (e.g. access aid)
• "Proximity warning device" (with code (219) DISTRONIC)

As of 1.7.11, the "Acoustic locking-verification signal" menu item will also be part of the "Vehicle" submenu in the "Settings" menu Here the "acoustic locking feedback" can be switched on or off.

Trip computer menu 

The following information is shown on the "Trip computer" menu:

• After start (e.g. travel distance, journey time)
• After reset (e.g. travel distance, average fuel consumption)
• Range
• Momentary fuel milage

"Telephone" menu (with code (386) Mobile phone) 

The "Telephone" menu can be used to call up the following information:

• Status
• Messages

"Workshop level" menu 

The Workshop level menu is not a separate menu item and can be called up as follows:

• Instrument cluster display in basic menu
• Press trip odometer reset button (A1s3) three times within t = 1.5 s