Abbreviations in the painting sector - AH98.00-P-9409-01A
Model 124, 126, 129, 140, 163, 164, 166, 168, 169, 170, 171, 172, 199, 201, 202, 203, 204, 207, 208, 209, 210, 211, 212, 215, 216, 218, 219, 220, 221, 230, 240, 245.2, 251, 463
General abbreviations
AbfG Waste Disposal Law
AbfNachwV Waste Verification Act
AbwAG Waste Water Disposal Law
AVwV General Administrative Regulation
ATL Anodic immersion painting
ATV Specifications governing waste water handling as set forth in the German Waste Water Association e.V.
bar (atmospheres) Measurement of air pressure
BImSchG Law for the Protection Against Harmful Environmental Effects of Air Pollution, Federal Immissions Law
DD Two-component polyurethane paint with designation "Desmophen Desmodur"
DIN German Institute for Standardization
DNA Committee for German Standards
Elex V Regulations on Electrical Facilities in Hazardous Locations
EPC Electro powder coating (ETL)
ETL Electro immersion painting
GPSG Technical working materials and consumer products act
GefStoffV Hazardous Substances Act
GGVS Hazardous Goods Transport Regulations
Sulfuric acid anodizing Impulse limit volume spray
HS High solid
KTL Cathodic immersion painting
KH Artificial resin
KS Plastic
MAK Maximum workplace concentration
MBL Mercedes-Benz Delivery Specifications
ms Medium solid
OWiG Infringement Law
PVK Pigment volume concentration
pH-value Potential hydrogenium concentration of hydrogen ions in a hydrous solution
RAL "Reich" Committee for Terms of Delivery and Quality Assurance at the Committee for German Standards
TA Noise German Noise Act
TA Air German Clean Air Act
TRbF Technical Rules for Flammable Liquids
TRgA Technical Rules for Hazardous Materials
Trg A Technical Directives for Hazardous Materials
TRGS Technical Rules for Hazardous Substances
USB Environment officer
UWS Environmental protection
VAwS Directive on Facilities for the Storage, Bottling and Turnaround of Substances Harmful to Ground Water
VBF (Front control panel) Directive on Flammable Liquids
VDI Directives of the Association of German Engineers
VLwF Directive on the Storage of Liquids Harmful to Ground Water
WHG Water Resources Law
μm 1 micrometer=1/1000 mm, unit of measurement of coating thickness
2 K Two-component
Abbreviations for hazardous materials classes
A I Flash point below 21 °C
A II Flash point above 21 °C to 55 °C
A III Flash point above 55 °C to 100 °C
Abbreviations for plastics
ABS Acrylonitrile-butadiene-styrene
AMMA Acrylonitrile-methylmethacrylate
BFK Boron filament reinforced plastic
CA Cellulose acetate
CAB Cellulose acetate butyrate
CFK Carbon-fiber reinforced plastic
EP Epoxy
FEP Perfluoroethylene propylene
GF Glass fiber
GFK Glass fiber reinforced plastic
HDPE High density polyethylene
LDPE Low density polyethylene
MF Melamine formaldehyde
PA Polyamide
PBTP Polybutylene terephthalate
PC Polycarbonate
PE Polyethylene
PEC Chlorinated polyethylene
PETP Polyethylene terephthalate
PF Phenol formaldehyde
PIB Polyisobutylene
PMMA Polymethyl methacrylate
POM Polyoxymethylene, polyformaldehyde (a polyacetate)
PP Polypropylene
PP-EPDM Polypropylene ethylene propylene diene copolymer
PP-PMMA Polypropylene polymethyl methacrylate
PPO Polyphenylene oxide
PPS Polyphenylene sulfide
PSU Polysulfone
PS Polystyrene
PTFE Polytetrafluor ethylene
PUR Polyurethane
PVC Polyvinyl chloride
PVCC Chlorinated polyvinyl chloride
PVDC Polyvinylidene chloride
PVDF Polyvinylidene fluoride
PVF Polyvinyl fluoride
RTPU-GF Reinforced Thermoplastic Polyurethane - glass-fiber reinforced PUR polyurethane
SAN Styrene-acrylonitrile
Std. Styrene-butadiene
SI Silicone
SMS Styrene-alpha-methylstyrene
UF Urea formaldehyde
VP Unsaturated polyester
VPE Vulcanized polyethylene