Press in guide sleeve - AR41.10-P-0200-03TX
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE
| Number | Designation | Model 204.203, model 204.003 with manual transmission | ||
|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 25.3 |
| Rear propeller shaft | mm | 36.2 |
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE
| Number | Designation | Model 204.003 with automatic transmission | Models 204.000/002/200/202 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 24.8 | 24.8 |
| Rear propeller shaft | mm | 36.2 | 36.3 |
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE
| Number | Designation | Model 204.008/047/056/065/208/247/256/901/902/956 | Model 204.006/007/041/044/045/046/048/049/052/054/081/082/085/087/089/092/207/241/245/246/248/249/252/254/282/289/292/981/982/983/984/987/992 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 24.8 | 23.3 |
| Rear propeller shaft | mm | 28.3 | 26.8 |
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE
| Number | Designation | models 204.022/025/222/225 | Model 204.077/277 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 25, 3 | 28, 8 |
| Rear propeller shaft | mm | 28, 8 | 28, 8 |
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE
| Number | Designation | Model 207.320/322/372/420/422/472 | Model 207.347/356/357/447/456/457 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 25.3 | 24.8 |
| Rear propeller shaft | mm | 28.8 | 28.3 |
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE
| Number | Designation | Model 212.002/005/202/205 | Model 212.003/020/074/077/203/220/274/277, model 212.024/025/224/225 with auto. transmission | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 24.8 | 25.3 |
| Rear propeller shaft | mm | 36.3 | 36.2 |
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE
| Number | Designation | Model 212.023/072/223, 272, model 212.024/025/224/225 with man. transmission | Model 212.041/048/054/082/084/087/089/090/147/148/248/254/282/284/287/288/289 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 25.3 | 23.3 |
| Rear propeller shaft | mm | 28.8 | 26.8 |
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE
| Number | Designation | Model 212.053/056/057/256/257 | ||
|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 36.3 |
| Rear propeller shaft | mm | 28.3 |
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE
| Number | Designation | Model 218.303/323/373 | Model 218.359 without code 460/494 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 25.3 | 36.3 |
| Rear propeller shaft | mm | 28.8 | 28.3 |
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE
| Number | Designation | Model 218.359 with code 460/494, model 218.391 | Model 218.374 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 24.8 | 25.3 |
| Rear propeller shaft | mm | 28.3 | 36.2 |
CHECK VALUES FOR PROPELLER SHAFT ALIGNMENT SLEEVE
| Number | Designation | Model 219.354 | Model 219.322/372 | Model 219.356/357/375/376/377 | ||
|---|---|---|---|---|---|---|
| BE41.10-P-1001-02L | Insertion dimension "a" from face end of alignment sleeve to joint flange | Front propeller shaft | mm | 23.3 | 25.3 | 24.8 |
| Rear propeller shaft | mm | 26.8 | 28.8 | 28.3 | ||
| See picture | - | - | - |
- Use a suitable drift to drive in the new guide sleeve.
Observe press-in dimension (a) from the end face of the centering sleeve to the flange.
The specified press-in distance (a) may deviate depending on the thickness of the flexible couplings, e.g. in vehicles with vibration damper. In these cases the dimension (a) measured prior to removal should be used for installation.