Retrofit media interface power supply wiring harness - AN82.60-P-0016-03FH

Fig 1: Identifying Wiring Harness Repair Kit (000 589 13 99 00)

Courtesy of MERCEDES-BENZ USA

Fig 2: Identifying New Passenger Vehicle Wiring Harness Repair Kit (220 589 04 99 00)

Courtesy of MERCEDES-BENZ USA

Connection scheme 

Fig 3: Identifying Retrofit Media Interface Power Supply Connection Diagram

Courtesy of MERCEDES-BENZ USA

Routing diagram 

Fig 4: Identifying Retrofit Media Interface Power Supply Routing Diagram

Courtesy of MERCEDES-BENZ USA

1. Route red/white line (rt/ws), as shown, under the right front floor covering and fasten in place using felt tape.

   The red/white line (rt/ws) is routed to the rear SAM control unit with fuse and relay module. The yellow 14-pin plug (9) will be connected to the yellow 14-pin coupling of the power supply wiring harness in the front passenger footwell at a later point in time.

   Fig 5: Identifying Voltage Supply Line And Yellow 14-Pin Plug

   Courtesy of MERCEDES-BENZ USA
2. Route red/white line (rt/ws) along the vehicle wiring harness (24) into the right side of the trunk.
3. Fasten red/white line (rt/ws) using cable ties to vehicle wiring harness (24).
   Fig 6: Identifying Vehicle Wiring Harness And Voltage Line

   Courtesy of MERCEDES-BENZ USA

   Perform operation step 4 only when green 7-pin fuse carrier (25) is not installed.

4. Install green 7-pin fuse carrier of media interface wiring harness with connected red/white line (rt/ws) to rear SAM control unit with fuse and relay module (N10/2).

   Perform operation steps 5 to  7 only when the green 7-pin fuse carrier (25) is installed.

5. Release catch hooks (arrows B) and remove green 7-pin fuse carrier (25) at rear SAM control unit with fuse and relay module (N10/2).
   Fig 7: Identifying Green 7-Pin Fuse Carrier, Fuse And Relay Module

   Courtesy of MERCEDES-BENZ USA
6. Remove red/white line (rt/ws) from green 7-pin fuse carrier of media interface wiring harness.
7. Insert red/white line (rt/ws) into contact cavity 1 of green 7-pin fuse carrier (25) and install green 7-pin fuse carrier (25) onto rear SAM control unit with fuse and relay module (N10/2).

   The designation of the individual contact cavities is on the green 7-pin fuse carrier (25) (arrow C).

8. Insert electrical fuse with a fuse rating of 7.5 amps into slot 1 on the green 7- pin fuse carrier (25).
   Fig 8: Identifying 7-Pin Fuse Carrier

   Courtesy of MERCEDES-BENZ USA
9. Join yellow 14-pin coupling (8) of red/white line (rt/ws) with yellow 14-pin plug (9).
10. Route brown line (br) into front passenger footwell.
11. Connect brown line (br) to ground point (right front footwell) (W15/7).
12. Fasten red/white line (rt/ws) and brown line (br) onto vehicle wiring harness using cable ties.

    Form loops with excess lengths of red/white line (rt/ws) and brown line (br) and fasten in place using cable ties.

    Fig 9: Identifying Red/White Line, Brown Line And Right Front Footwell

    Courtesy of MERCEDES-BENZ USA
13. Route blue line (bl) from installation location of media interface control unit (arrow A) along the vehicle wiring harness into the installation opening of the audio equipment and fasten in place using cable ties.
    Fig 10: Identifying Blue Line And Media Interface Control Unit Routing

    Courtesy of MERCEDES-BENZ USA

    Perform operation steps 14 to  17 only for one of the following codes:

    • without  code (537) Digital radio or
    • Without  code (810) Sound system.
14. Fit contact spring SLK (27) on blue line (bl).

    The contact spring SLK (27) is available in the wiring harness repair kit supplement for passenger cars.

15. Release lock (28) at black 44-pin coupling (21).
    Fig 11: Identifying Contact Spring SLK, Black 44-Pin Coupling And Lock

    Courtesy of MERCEDES-BENZ USA
16. Fit SLK contact spring SLK (27) of blue line (bl) into contact cavity 16 (arrow E) of black 44-pin coupling (21).
17. Relock lock (28) at black 44-pin coupling (21).

    Perform operation step 18 for vehicles with one of the following codes:

    • with  code (537) Digital radio or
    • With  code (810) Sound system.
18. Connect blue line (bl) using a potential distributor (29) to the blue/black wake-up signal line (bl/sw) of the vehicle wiring harness.
    Fig 12: Identifying Blue Line, Potential Distributor And Blue/Black Wake-Up Signal Line

    Courtesy of MERCEDES-BENZ USA

    The blue/black line (bl/sw) of the vehicle wiring harness is located in contact cavity 16 (arrow E) of the black 44-pin coupling (21).

    The potential distributor (29) is available in the new passenger car wiring harness repair kit.