Status indicator, location/function - GF82.95-P-2002R
MODELS 230 up to 31.5.04 with CODE (855) TELE AID
Status display in instrument cluster (A1)
Behavior of status indicator in SOS pushbutton switch (S93/3)
The status indicator in the SOS pushbutton switch (S93/3) is used to check the function of the TELE AID system.
Every time the TELE AID system is switched on the status indicator comes on for approx. 4 s and signals the readiness for TELE AID for an emergency call. Then the status indicator goes out. If a TELE AID emergency call is activated, the status display begins flashing (0.5 s on, 0.5 s off, ...) and a message appears in the display of the instrument cluster (A1) (see Fig. above, text field 1). If it was not possible to transmit a TELE AID emergency call (data and voice) and no 911 emergency call was able to be placed, the status indicator comes on and a message appears in the display of the instrument cluster (A1) (see Fig. above, text field 2). If a voice connection is completed, the status indicator returns the same status as before the emergency call actuation and a message appears on the instrument cluster (A1) display.
If the TELE AID system is in the diagnosis mode the status indicator also starts flashing.
A TELE AID system error is present when the status indicator does not go out 5 s after switching on or when it comes on at a later time. A message then appears in the display of the instrument cluster (A1) (see Fig. above, text field 3).
Permanent illumination of the status indicator can have the following causes:
External error
- Tilting cone sensor (B66) faulty
- Power supply too low
- No or incorrect SIM card installed
- Communication with restraint system control unit (N2/7) interrupted
- Error in communication with ESP, SPS and BAS control unit (N47-5)
- Error on SOS pushbutton switch (S93/3)
- Error on GPS reception (antenna system)
- Error in reception with TELE AID backup antenna (A2/50) or CTEL antenna (A2/22)
Internal error
- GPS reception erroneous
- Vehicle is not authorized or is in the process of authorization
- Memory defect on telephone transmitter/receiver and TELE AID, D2B (A35/17)
- The PIN (Personal Identification Number) has not been stored in the telephone transmitter/receiver and TELE AID, D2B (A35/17) by the user (e.g. after changing PIN number)
- Integral telephone transmitter/receiver and TELE AID, D2B (A35/17) faulty
The CTEL and TELE AID transmitter/receiver, D2B (A35/17) can be coded with STAR Diagnosis so that the status indicator does not come on even when the system is not authorized (all other system errors are indicated).
The dealer should have the customer confirm deactivation of the status indicator in writing using a preprinted form.
| TELE AID switch-on/switch-off characteristics, function | GF82.95-P-2000R | ||
| Authorization, function | GF82.95-P-2001R | ||
| Emergency call actuation, function | GF82.95-P-2003R | ||
| PIN check with TELE AID emergency call, function | GF82.95-P-3002R | ||
| Restraint system control unit data, function | GF82.95-P-3005R | ||
| Transmitter/receiver unit, location/task/design/function | for telephone and TELE AID | GF82.95-P-4300R | |
| TELE AID pushbutton, location/task/design/function | GF82.95-P-4101R | ||
| Telephone antenna, location/task | GF82.62-P-4105R | ||
| TELE AID substitute antennas, location/task/design/function | GF82.95-P-4102R | ||
| Rollover sensor, location/task | GF82.95-P-4206R |