Set up Celette straightening bench - AR60.10-P-1060GZ

MODEL 164 

Fig 1: Identifying Celette Straightening Bench

Courtesy of MERCEDES-BENZ USA

	Installation, removal
	Risk of death  caused by vehicle slipping or toppling off of the lifting platform.	Align vehicle between the columns of the lifting platform and position the four support plates at the lifting platform support points specified by the vehicle manufacturer.	AS00.00-Z-0010-01A
1	Lift vehicle with two-post lift	Two-post lift	*WE58.40-Z-1001-05A
2	Set-up Celette straightening bench (1)	Celette straightening bench M8S	*WE58.40-Z-1001-01E
		NT 10 Celette straightening bench	*WE58.40-Z-1001-01E
		Celette straightening bench Sevenne	*WE58.40-Z-1001-01E
	Setup of module members (base frame)
3	Install Celette module members	Model 164.1	AR60.10-P-1060-01GZ
		Model 164.8	AR60.10-P-1060-01GY
		Screwdriver insert 8 mm for hexagon socket head screws	*WH58.30-Z-1026-06A
		Reversible ratchet	*WH58.30-Z-1007-06A
		Pneumatic ratchet 1/2"	*WE58.40-Z-1008-03A
		Double end box wrench, offset, 22X24 mm	*WH58.30-Z-1002-11A
		Celette straightening bench M8S	*WE58.40-Z-1001-01E
		NT 10 Celette straightening bench	*WE58.40-Z-1001-01E
		Celette straightening bench Sevenne	*WE58.40-Z-1001-01E
		Set of Celette module members 955.940	*WE58.40-Z-1007-01E
		Celette additional member 955.908	*WE58.40-Z-1008-01E
	Setup of Celette straightening tools and multi-Z elements (for body work)
4	Install Celette straightening tool and multi-Z-elements	Model 164.1	AR60.10-P-1060-02GZ
		Model 164.8	AR60.10-P-1060-02GY
		Reversible ratchet	*WH58.30-Z-1007-06A
		Pneumatic ratchet 1/2"	*WE58.40-Z-1008-03A
		Double end box wrench, offset, 17X19 mm	*WH58.30-Z-1001-11A
5	Remove stop plugs from jack support points
6	Set vehicle onto straightening bench
7	Align vehicle on straightening bench	Observe check bore!
8	Fasten vehicle to straightening bench
	Setup of portal frame and of welding devices (for operations on A, B, C and D-pillars)
9	Install side portal with portal straightening set	Only when required for repair to vehicle.
		Model 164.1	AR60.20-P-1550-01GZ
		Portal frame	Fig 2
		Inspection and welding devices	Fig 3
		Type 164.8	AR60.20-P-1550-01GY
		Portal frame	Fig 2
		Inspection and welding devices	Fig 3
		Welding device Model 164	Fig 4
		Screwdriver insert 8 mm for hexagon socket head screws	*WH58.30-Z-1026-06A
		Socket wrench insert, SW 19 for hex. socket head bolts	*WH58.30-Z-1010-06A
		Reversible ratchet	*WH58.30-Z-1007-06A
		Pneumatic ratchet 1/2"	*WE58.40-Z-1008-03A
		Double end box wrench, offset, 17X19 mm	*WH58.30-Z-1001-11A
		Double end box wrench, offset, 22X24 mm	*WH58.30-Z-1002-11A
10	Detach in the reverse order

Fig 2: Identifying Portal Frame (129 589 03 23 00)

Courtesy of MERCEDES-BENZ USA

Fig 3: Identifying Inspection And Welding Devices (164 589 00 23 00)

Courtesy of MERCEDES-BENZ USA

Fig 4: Identifying Welding Device (164 589 03 23 00)

Courtesy of MERCEDES-BENZ USA

COMMERCIALLY AVAILABLE TOOLS

Number	Designation
WH58.30-Z-1007-06A	Reversible ratchet
WH58.30-Z-1010-06A	Socket SW19 for hexagon head screws
WH58.30-Z-1026-06A	Screwdriver bit, 8 mm for hexagon socket head screws
WH58.30-Z-1001-11A	Double end box wrench, offset, 17 x 19 mm
WH58.30-Z-1002-11A	Double end box wrench, offset, 22 x 24 mm

WORKSHOP EQUIPMENT

WE58.40-Z-1001-01E	Celette straightening bench
WE58.40-Z-1007-01E	Celette module crossmember set 955.940
WE58.40-Z-1008-01E	Celette additional member 955.908
WE58.40-Z-1008-03A	Pneumatic ratchet
WE58.40-Z-1001-05A	Two-post lifting platform