Location and assignment of Z connector sleeves (cable connections in wiring harness) - engine compartment, right - GF00.19-P-3000-02CAA
Model 216
| Z connector sleeve | Designation | Component | Designation | Connector. Pin |
|---|---|---|---|---|
| Engines 157, 278 | ||||
| Z5 | Connector sleeve (solder connector in harness) | ← N3/10 | ME-SFI [ME] control unit | M.17 |
| →B28/4 | Pressure sensor downstream of air filter, left cylinder bank | 3 | ||
| →B28/5 | Pressure sensor downstream of air filter, right cylinder bank | 3 | ||
| →B28/6 | Pressure sensor upstream of throttle valve actuator | 3 | ||
| Engine 273 | ||||
| Z5(2) | Connector sleeve (solder connector in harness) | ← N3/10 | ME-SFI [ME] control unit | 1.44 |
| →B28 | Pressure sensor | 3 | ||
| →B28/9 | Left intake manifold tumble flap position sensor | 1 | ||
| →B28/10 | Right intake manifold tumble flap position sensor | 1 | ||
| Engines 157, 278 | ||||
| Z6z1 | Ground connector sleeve | ← W34/1 | Ground (electronics - left footwell) | |
| →T1/1 | Cylinder 1 ignition coil | 1 | ||
| →T1/2 | Cylinder 2 ignition coil | 1 | ||
| →T1/3 | Cylinder 3 ignition coil | 1 | ||
| →T1/4 | Cylinder 4 ignition coil | 1 | ||
| Start/stop | → W11/2 | Ground (engine, right) | ||
| →Z6z2 | Ground connector sleeve | |||
| Z6/26 | Sensor supply connector sleeve | |||
| M273 | ← N3/10 | ME-SFI [ME] control unit | 1.40 | |
| M273 | → G3/5 | Left O2 sensor, downstream CAT | x1.3 | |
| M273 | → G3/6 | Right O2 sensor, downstream CAT | x1.3 | |
| Z6/27 | Sensor ground connector sleeve | |||
| M156 | ← N3/10 | ME-SFI [ME] control unit | 1.15 | |
| M156 | → B11/4 | Coolant temperature sensor | 2 | |
| M156 | → B17 | Intake air temperature sensor | 2 | |
| M156 | → B28 | Pressure sensor | 1 | |
| Z6/30(1) | Circuit 31 connector sleeve | |||
| ← W15/3 | Ground (electronics) | |||
| →T1/1 | Cylinder 1 ignition coil | 2 | ||
| →T1/2 | Cylinder 2 ignition coil | 2 | ||
| →T1/3 | Cylinder 3 ignition coil | 2 | ||
| →T1/4 | Cylinder 4 ignition coil | 2 | ||
| Z6/48(1) | Ground connector sleeve | |||
| M273 | ← Z6/48 | Ground connector sleeve | 2 | |
| M273 | → T1/1 | Cylinder 1 ignition coil | 2 | |
| M273 | → T1/2 | Cylinder 2 ignition coil | 2 | |
| M273 | → T1/3 | Cylinder 3 ignition coil | 2 | |
| M273 | → T1/4 | Cylinder 4 ignition coil | 2 | |
| Z7/35(1) | Circuit 87M1e connector sleeve | |||
| M273 | ← Z7/35 | Circuit 87M1e connector sleeve | 2 | |
| M273 | → T1/2 | Cylinder 2 ignition coil | 1 | |
| M273 | → T1/3 | Cylinder 3 ignition coil | 1 | |
| M273 | → Y62y2 | Cylinder 2 fuel injection valve | 1 | |
| M273 | → Y62y3 | Cylinder 3 fuel injection valve | 1 | |
| M273 | → Y62y8 | Cylinder 8 fuel injection valve | 1 | |
| M157, M278 | ||||
| Z7/35z2 | Front CAN (high) sensor connector sleeve | ← N10/1 | Front SAM control unit with fuse and relay module | M1.2 |
| →B6/4 | Left intake camshaft Hall sensor | 1 | ||
| →B6/6 | Left exhaust camshaft Hall sensor | 1 | ||
| →Z7/35z1 | Circuit 87 M1e connector sleeve | |||
| Z7/35(4) | Circuit 87 M1e connector sleeve | |||
| M156 | ← Z7/35 | Circuit 87M1e connector sleeve | 1 | |
| M156 | → B2/7 | Right hot film MAF sensor | 1 | |
| M156 | → Y62y1 | Cylinder 1 fuel injection valve | 1 | |
| M156 | → Y62y2 | Cylinder 2 fuel injection valve | 1 | |
| M156 | → Y62y3 | Cylinder 3 fuel injection valve | 1 | |
| M156 | → Y62y4 | Cylinder 4 fuel injection valve | 1 | |
| Z7/36(1) |
Circuit 87 M2e connector sleeve | |||
| M273 | ← Z7/36 | Circuit 87 M2e connector sleeve | 2 | |
| M273 | → G3/3 | Left O2 sensor, upstream CAT | x1.4 | |
| M273 | → G3/4 | Right O2 sensor, upstream CAT | x1.4 | |
| M273 | → G3/5 | Left O2 sensor, downstream CAT | x1.1 | |
| M273 | → G3/6 | Right O2 sensor, downstream CAT | x1.1 | |
| M273 | → Y16/2 | Heating system shutoff valve | 1 | |
| M273 | → Y32 | Air pump switchover valve | 1.2 | |
| Z7/36z2 | M157, M278 | |||
| Circuit 87 M2e connector sleeve | ← Z7/36z1 | Circuit 87 M2e connector sleeve | ||
| M157 | → B40 | Oil sensor (oil level, temperature and quality) | ||
| →G3/6 | Right O2 sensor, downstream CAT | x1.1 | ||
| →Y77/1 | Charge pressure positioner | 1 | ||
| →Y130 | Engine oil pump valve | 1 | ||
| Z7/38(1) |
Circuit 87M1i connector sleeve | |||
| M273 | ← Z7/38 | Circuit 87 M1i connector sleeve | 2 | |
| M273 | → B6/5 | Right intake camshaft Hall sensor | 3 | |
| M273 | → B6/7 | Right exhaust camshaft Hall sensor | 3 | |
| M273 | → C4/1 | Radio interference suppression capacitor 1 | 1 | |
| M273 | → T1/1 | Cylinder 1 ignition coil | 1 | |
| M273 | → T1/4 | Cylinder 4 ignition coil | 1 | |
| M273 | → Y49/5 | Right intake camshaft solenoid | 2 | |
| M273 | → Y49/7 | Right exhaust camshaft solenoid | 2 | |
| M273 | → Y62y1 | Cylinder 1 fuel injection valve | 1 | |
| M273 | → Y62y4 | Cylinder 4 fuel injection valve | 1 | |
| M273 | → Y62y7 | Cylinder 7 fuel injection valve | 1 | |
| Z7/38(1) | Circuit 87M1i connector sleeve | |||
| M275 | ← Z7/38 | Circuit 87 M1i connector sleeve | ||
| M275 | → C4/1 | Radio interference suppression capacitor 1 | ||
| M275 | → N91 | ECI ignition system power pack | 4 5 |
|
| M275 | → Y62y1 | Cylinder 1 fuel injection valve | 1.1 | |
| M275 | → Y62y2 | Cylinder 2 fuel injection valve | 2.1 | |
| M275 | → Y62y3 | Cylinder 3 fuel injection valve | 3.1 | |
| M275 | → Y62y4 | Cylinder 4 fuel injection valve | 4.1 | |
| M275 | → Y62y5 | Cylinder 5 fuel injection valve | 5.1 | |
| M275 | → Y62y6 | Cylinder 6 fuel injection valve | 6.1 | |
| M275 | → Z7/38 | Circuit 87 M1i connector sleeve | 2 | |
| Engine 273 | ||||
| Z7/38(2) | Circuit 87 M1i connector sleeve | ← Z7/38 | Circuit 87 M1i connector sleeve | 1 |
| → B2/5 | Hot film mass air flow sensor | 1 | ||
| → N10/1 | Front SAM control unit with fuse and relay module | M1.3 | ||
| →T1/6 | Cylinder 6 ignition coil | 1 | ||
| →T1/7 | Cylinder 7 ignition coil | 1 | ||
| →Y49/4 | Left intake camshaft solenoid | 2 | ||
| →Y49/6 | Left exhaust camshaft solenoid | 2 | ||
| →Y62y5 | Cylinder 5 fuel injection valve | 1 | ||
| →Y62y6 | Cylinder 6 fuel injection valve | 1 | ||
| Engine 275 | ||||
| Z7/39 | Circuit 87 M2i connector sleeve | ← N10/1 | Front SAM control unit with fuse and relay module | M1.6 |
| →G3/3 | Left O2 sensor, upstream CAT | x1.1 | ||
| →G3/4 | Right O2 sensor, upstream CAT | x1.1 | ||
| →Y32 | Air pump switchover valve | 1 | ||
| →Y101 | Divert air switchover valve | 2 | ||
| Engine 275 | ||||
| Z7/41 | Sensor supply connector sleeve | ← N3/10 | ME-SFI [ME] control unit | 3.6 |
| →B6/3 | Camshaft Hall sensor, right cylinder bank | 3 | ||
| →B28/4 | Pressure sensor downstream of air filter, left cylinder bank | 3 | ||
| →B28/5 | Pressure sensor downstream of air filter, right cylinder bank | 3 | ||
| →B28/6 | Pressure sensor upstream of throttle valve actuator | 3 | ||
| →B28/7 | Pressure sensor downstream of throttle valve actuator | 3 | ||
| →B40 | Oil sensor (oil level, temperature and quality) | 3 | ||
| Engine 273 | ||||
| Z7/43 | Sensor ground connector sleeve | ← N3/10 | ME-SFI [ME] control unit | 1.15 |
| →B6/5 | Right intake camshaft Hall sensor | 1 | ||
| →B6/7 | Right exhaust camshaft Hall sensor | 1 | ||
| →B28 | Pressure sensor | 1 | ||
| →B28/10 | Right intake manifold tumble flap position sensor | 2 | ||
| Engine 275 | ||||
| Z7/43(1) | Sensor ground connector sleeve | ← Z7/43 | Sensor ground connector sleeve | 2 |
| →B11/4 | Coolant temperature sensor | 2 | ||
| →B17/8 | Charge air temperature sensor | 1 | ||
| →B28/5 | Pressure sensor downstream of air filter, right cylinder bank | 1 | ||
| →B28/7 | Pressure sensor downstream of throttle valve actuator | 1 | ||
| →B40 | Oil sensor (oil level, temperature and quality) | 2 | ||
| Engine 275 | ||||
| Z7/43(2) | Sensor ground connector sleeve | ← N3/10 | ME-SFI [ME] control unit | 3.4 |
| →B6/3 | Camshaft Hall sensor, right cylinder bank | 1 | ||
| →B28/4 | Pressure sensor downstream of air filter, left cylinder bank | 1 | ||
| →B28/6 | Pressure sensor upstream of throttle valve actuator | 1 | ||
| →Z7/43 | Sensor ground connector sleeve | 1 | ||
| Engine 273 | ||||
| Z7/44 | Sensor ground connector sleeve | ← N3/10 | ME-SFI [ME] control unit | 1.16 |
| →B6/4 | Left intake camshaft Hall sensor | 1 | ||
| →B6/6 | Left exhaust camshaft Hall sensor | 1 | ||
| →B11/4 | Coolant temperature sensor | 1.1 | ||
| →B28/9 | Left intake manifold tumble flap position sensor | 2 | ||
| Z7/98(1) | Circuit 87 connector sleeve M3e | |||
| M156 | ← Z7/98 | Circuit 87 connector sleeve M3e | 3 | |
| M156 | → C4/2 | Radio interference suppression capacitor 2 | 1 | |
| M156 | → T1/1 | Cylinder 1 ignition coil | 1 | |
| M156 | → T1/2 | Cylinder 2 ignition coil | 1 | |
| M156 | → T1/3 | Cylinder 3 ignition coil | 1 | |
| M156 | → T1/4 | Cylinder 4 ignition coil | 1 | |
| Z36/27 | Front PTS sensor voltage supply connector sleeve | |||
| Up to 08/07 | ← N62 | PTS control unit | b.34 | |
| As of 09/07 | ← N62 | PTS control unit | b.8 | |
| Up to 05/09 | → A86/1 | Front short range radar sensor unit | 1.4 4.4 |
|
| Valid for Distronic Plus | → | 2.4 | ||
| Valid for Distronic Plus | → | 3.4 | ||
| as of 06/09 | → A86/1b2 | Left inner radar sensor, front bumper | 4 | |
| As of 06/09 | → A86/1b3 | Right inner radar sensor, front bumper | 4 | |
| Up to 05/09 | → B8/1 | Outer left front PTS ultrasonic sensor | 3 | |
| Up to 05/09 | → B8/2 | Center left front PTS ultrasonic sensor | 3 | |
| Up to 05/09 | → B8/3 | Inner left front PTS ultrasonic sensor | 3 | |
| Up to 05/09 | → B8/4 | Inner right front PTS ultrasonic sensor | 3 | |
| Up to 05/09 | → B8/5 | Center right front PTS ultrasonic sensor | 3 | |
| Up to 05/09 | → B8/6 | Outer right front PTS ultrasonic sensor | 3 | |
| →Z3/19 | Circuit 15 connector sleeve (fused) (PTS) | |||
| Z36/16 | Front CAN (low) sensor connector sleeve | |||
| Up to 05/09 | ← N62/1 | Radar sensors control unit (SGR) | A.13 | |
| Up to 05/09 | → A86/1 | Front short range radar sensor unit | 1.3 | |
| Valid for Distronic Plus | → | 2.3 | ||
| Valid for Distronic Plus | → | 3.3 | ||
| → | 4.3 | |||
| As of 06/09 | → A86/1b2 | Left inner radar sensor, front bumper | 3 | |
| As of 06/09 | → A86/1b3 | Right inner radar sensor, front bumper | 3 | |
| As of 06/09 | → Z37/7 | CAN bus (low) connector sleeve | ||
| Z36/18 | Front CAN (high) sensor connector sleeve | |||
| Up to 05/09 | ← N62/1 | Radar sensors control unit (SGR) A. | 12 | |
| Up to 05/09 | → A86/1 | Front short range radar sensor unit | 1.2 | |
| Valid for Distronic Plus | → | 2.2 | ||
| Valid for Distronic Plus | → | 3.2 | ||
| → | 4.2 | |||
| As of 06/09 | → A86/1b2 | Left inner radar sensor, front bumper | 2 | |
| As of 06/09 | → A86/1b3 | Right inner radar sensor, front bumper | 2 | |
| As of 06/09 | → Z37/6 | CAN databus (high) connector sleeve |