Loosen front bumper and fasten - AR88.20-P-2000-01CW
WARNING: This page is about a different car, the 2011 Mercedes-Benz C350, 2010 Mercedes-Benz C350, 2009 Mercedes-Benz C350, and 2008 Mercedes-Benz C350. However, it is still accessible from the selected car via links, so may be relevant.
MODEL 204.0 /2 /3, 207, 212
CHECK VALUES FOR GAPS
| Number | Designation | Model 204.0 | Model 204.2 | |||
|---|---|---|---|---|---|---|
| BE60.00-P-1001-01U | Gap dimension | Engine hood to fender | Dimension "A" | mm | 4 (±1) | 4 (±1) |
| Engine hood to headlamp | Dimension "B" | mm | 4 (±1) | 4 (±1) | ||
| Engine hood to radiator grille | Dimension "C" | mm | 6 (±1) | 6 (±1) | ||
| Engine hood to bumper | Dimension "D" | mm | 4 (±1.5) | 4 (±1.5) | ||
| Engine hood to A-pillar | Dimension "E" | mm | 4.5 (±1) | 4.5 (±1) | ||
| Bumper to headlamp | Dimension "F" | mm | 3 (±1) | 3 (±1) | ||
| - | - | - |
CHECK VALUES FOR GAPS
| Number | Designation | Model 204.3 | |||
|---|---|---|---|---|---|
| BE60.00-P-1001-01W | Gap dimension | Engine hood to fender | Dimension "A" | mm | 4 (±1) |
| Engine hood to headlamp | Dimension "B" | mm | 4 (±1) | ||
| Engine hood to bumper | Dimension "C" | mm | 6 (+1/-2) | ||
| Engine hood to A-pillar | Dimension "D" | mm | 4.5 (+2/-1) | ||
| Bumper to headlamp | Dimension "E" | mm | 2.5 (±1.5) | ||
| - | - |
CHECK VALUES FOR GAPS
| Number | Designation | Model 207.3 | Model 207.4 | |||
|---|---|---|---|---|---|---|
| BE60.00-P-1001-01W | Gap dimension | Engine hood to fender | Dimension "A" | mm | 4 (±1) | 4 (±1) |
| Engine hood to headlamp | Dimension "B" | mm | 4 (±1) | 4 (±1) | ||
| Engine hood to bumper | Dimension "C" | mm | 6 (+1/-2) | 6 (+1/-2) | ||
| Engine hood to A-pillar | Dimension "D" | mm | 4.5 (+2/-1) | 4.5 (+2/-1) | ||
| Bumper to headlamp | Dimension "E" | mm | 2.5 (±1.5) | 2.5 (±1.5) | ||
| - | - | - |
CHECK VALUES FOR GAPS
| Number | Designation | Model 212.0/1 | Model 212.2 | |||
|---|---|---|---|---|---|---|
| BE60.00-P-1001-01U | Gap dimension | Engine hood to fender | Dimension "A" | mm | 4 (±1) | 4 (±1) |
| Engine hood to headlamp | Dimension "B" | mm | 4 (±1) | 4 (±1) | ||
| Engine hood to radiator grille | Dimension "C" | mm | - | - | ||
| Engine hood to bumper | Dimension "D" | mm | 4.5 (±1.5) | 4.5 ±1.5) | ||
| Engine hood to A-pillar | Dimension "E" | mm | 4.5 (±1.5) | 4.5 (±1.5) | ||
| Bumper to headlamp | Dimension "F" | mm | 3.5 (±1.5) | 3.5 (±1.5) | ||
| - | - | - |
Shown on model 204.0
Shown on model 212
The work procedure is shown on the right side of the vehicle as example.
- Remove quick-release coupling (16).
Only model 207, 212.
- Pivot air ducting (5) to side and unscrew bolt (6).
feeler gauge, adjust if necessary.
- Loosen fender liner (7) in area of bumper (9) and lift out with
- Unscrew bolts (10).
- Remove screw/bolt (11) of bracket (12).
- Pivot bracket (12) toward outside and press bumper (9) toward front.
- Pull bumper (9) toward front.
Carefully pull bumper (9) toward front to prevent damaging the bumper (9). Do not scratch or damage right front lamp unit (E2) or left front lamp unit (E1).
- Fasten in reverse order.