LEMON Manuals: Even more car manuals for everyone
Home >> Mercedes Benz >> 2010 >> C63 >> Repair and Diagnosis >> Electrical >> Motors, Switches, Relays >> Electrical System - Basic Knowledge - C63/C350 (204) - 2 Of 3 >> Basic Knowledge >> Route guidance through voice output, function - GF82.61-P-2011CW

Route guidance through voice output, function - GF82.61-P-2011CW

MODEL 204.0 with CODE (527) COMAND APS with single DVD drive (with navigation) up to Model Year 8 

MODEL 204.0 with CODE (512) COMAND APS with DVD changer up to Model Year 8 

MODEL 204.2 with CODE (527) COMAND APS with single DVD drive (with navigation) up to Model Year 8 

MODEL 204.2 with CODE (512) COMAND APS with DVD changer up to Model Year 8 

Function requirements 

General 

The route guidance through voice output function is an assistance function that assists the driver without distracting him from the traffic. The destination-oriented navigation of the navigation system is supported by voice outputs with the following information:

Voice output can be emitted in the following languages:

Special information on the voice output is issued in the following cases:

For vehicles except code (494) USA version, additional information is provided in the following instances:

Further voice outputs take place at the start of the route calculation, when an intermediate destination has been reached, or when the destination has been reached. On vehicles except code (494) USA version, for dynamic route guidance, additional voice messages are issued in response to routes influenced by traffic messages.

Function sequence for route guidance through voice outputs 

The navigation processor of the COMAND controller unit (A40/3) combines the word segments into complete instructions or information during a voice output and generates low frequency (LF [NF]) signals. The LF signals are forwarded, if necessary, over the Media Oriented System Transport (MOST) to the sound system amplifier control unit (N40/3) (with code (810) Sound system), where they are amplified and output over discrete lines to the following speakers:

For vehicles except code (810) Sound system, the LF signals are amplified in the COMAND controller unit and forwarded over discrete lines straight to the following speakers:

Operating instructions 

The COMAND controller unit is operated by the following components:

IMPORTANT During an active voice output the volume of the announcement can be adjusted by the following components:

REFER TO SYSTEM WIRING DIAGRAMS Electrical function diagram for navigation system With code (512) COMAND APS with DVD changer
with CODE (494) USA version
With code (359) TELE AID emergency call system
with CODE (810) Sound system
PE82.85-P-2051-99FAA
With code (512) COMAND APS with DVD changer
With code (527) COMAND APS with Single DVD disk drive (with navigation) with CODE (810) Sound system Except code (494) USA version
PE82.85-P-2051-99FAB
  Front central operating unit, component description A40/9 GF54.21-P-4500CW
  Cockpit central display, component description A40/8
High
GF54.30-P-6100CWH
  COMAND controller unit, component description A40/3
With code (527) COMAND APS with Single DVD disk drive (with navigation)
GF82.85-P-3136CW
A40/3
With code (512) COMAND APS with DVD changer
GF82.85-P-3136CWA
  Telephone and GPS roof antenna component description A28/11 GF82.62-P-4119CW 
  GPS antenna splitter, component description A2/5
Model 204.0
With code (359) TELE AID emergency call system
With code (512) COMAND APS with DVD changer
GF82.62-P-3129CWU 
  Speaker system, component description H4/1, H4/2, H4/3, H4/4, H4/27 Except code (810) Sound system GF82.62-P-4220CW 
H4/1, H4/2, H4/3, H4/4, H4/27, H4/29, H4/54, H4/57
with CODE (810) Sound system
GF82.62-P-4220CWS