Adjust wiper arms - AR82.30-P-6100-01CW
WIPER ARM TEST AND ADJUSTMENT VALUES
| Number | Designation | Model 197 | Model 204 | ||
|---|---|---|---|---|---|
| BE82.30-P-1003-01M | Angle of incidence of wiper arm on driver-side in parked position | Left-hand drive vehicle | ∠° | +2.0 to +6.0 | +3.0 to +7.0 |
| Right-hand drive vehicle | ∠° | -2.0 to -6.0 | -3.0 to -7.0 | ||
| BE82.30-P-1004-01M | Angle of incidence of wiper arm on front passenger side in parked position | Left-hand drive vehicle | ∠° | +3.0 to +7.0 | +3.0 to +7.0 |
| Right-hand drive vehicle | ∠° | -3.0 to -7.0 | -3.0 to -7.0 | ||
WIPER ARM TEST AND ADJUSTMENT VALUES
| Number | Designation | Model 207 | Model 212 | ||
|---|---|---|---|---|---|
| BE82.30-P-1003-01M | Angle of incidence of wiper arm on driver-side in parked position | Left-hand drive vehicle | ∠° | +3.0 to +7.0 | +3.0 to +7.0 |
| Right-hand drive vehicle | ∠° | -3.0 to -7.0 | -3.0 to -7.0 | ||
| BE82.30-P-1004-01M | Angle of incidence of wiper arm on front passenger side in parked position | Left-hand drive vehicle | ∠° | +3.0 to +7.0 | +3.0 to +7.0 |
| Right-hand drive vehicle | ∠° | -3.0 to -7.0 | -3.0 to -7.0 | ||
WIPER ARM TEST AND ADJUSTMENT VALUES
| Number | Designation | Model 218 | ||
|---|---|---|---|---|
| BE82.30-P-1003-01M | Angle of incidence of wiper arm on driver-side in parked position | Left-hand drive vehicle | ∠° | +3.0 to +7.0 |
| Right-hand drive vehicle | ∠° | -3.0 to -7.0 | ||
| BE82.30-P-1004-01M | Angle of incidence of wiper arm on front passenger side in parked position | Left-hand drive vehicle | ∠° | +3.0 to +7.0 |
| Right-hand drive vehicle | ∠° | -3.0 to -7.0 | ||
The setting of the angle of incidence on the driver-side wiper arm and passenger-side wiper arm is always done in the parked position and only when the check values differentiate from the tolerance range in the reverse or parked position. In doing so, the driver-side wiper arm or front passenger-side wiper arm is distorted by at least the value of the tolerance deviation in reverse position.
Use adjustment levers (Z4) from
adjustment tool set.
Shown on driver-side wiper arm in parked position
Mount angle gauge (A) with
adapter (B) onto the wiper arm to be adjusted.
- Lower wiper arm until all three contact points of the base of the
angle measuring device (A) touch the windshield.
Place adjustment levers (Z4) as far apart from each other as possible on this wiper arm.
The wiper arm is twisted with the aid of the
adjuster lever (Z4), which was positioned close to the
angle measuring device (A). The second
adjuster lever (Z4) is used as a counterholder.
Press adjustment lever (Z4) in the required direction until the wiper arm is at least distorted by the value of the tolerance deviation in reverse position.
Remove adjuster lever (Z4) from wiper arm.
- Read off angle of incidence for adjusted wiper arm on scale of
angle gauge (A), note it down and compare against the test and adjustment values, adjust again if necessary.
Remove angle gauge (A) with
adapter (B) from adjusted wiper arm.