LEMON Manuals: Even more car manuals for everyone
Home >> Mercedes Benz >> 2009 >> SLK300 Automatic >> Repair and Diagnosis >> Accessories & Equipment >> Wiper/Washer Systems >> Electrical System - Body - 171 Chassis >> Retrofitting & Conversion >> Retrofit wiring harness - AN82.61-P-0001 >> Retrofit wiring harness - AN82.61-P-0001-01VC

Retrofit wiring harness - AN82.61-P-0001-01VC

  1. Insert breaker point bracket (3) of red line (rt) into chamber 4 of black, 4-pin connector of ground wiring harness (2) for audio gateway control unit (N93/1).

    IMPORTANT Breaker point bracket (3) should catch audibly. The red line (rt) is the voltage supply for the audio gateway control unit (N93/1) and is located in the right footwell next to the audio gateway control unit (N93/1).

    Fig 1: Inserting Breaker Point Bracket Of Red Line Into Chamber 4 Of Black
    G05030717Courtesy of MERCEDES-BENZ USA
  2. Connect blue/white line (bl/ws) of black, 4-pin connector of ground wiring harness (2) with a voltage distributor (11) to blue/ white line (bl/ws) of branch-off line (10) of on-board wiring harness.
  3. Connect black, 4-pin connector to left connection of audio gateway control unit (N93/1) (see arrow).
  4. Connect brown line (br) of black, 4-pin connector to ground (right footwell) (W15/1).

    IMPORTANT Branch-off line (10) is assigned to a brown/red (br/rt), a brown (br), a blue/white (bl/ws), a pink (rs), and a yellow (ge) line. The pink line (rs) is already connected with a voltage distributor (11).

    Fig 2: Connecting Black, 4-Pin Connector To Left Connection Of Audio Gateway Control Unit (N93/1)
    G05030718Courtesy of MERCEDES-BENZ USA
  5. Connect lines that have identical color of new wiring harness (13) to black, 6-pin connector for audio gateway control unit (N93/1) with one voltage distributor (11) each at the lines of the branch-off line (10) of the on-board wiring harness.

    IMPORTANT The blue/white (bl/ws) and the pink (rs) line of the branch-off line (10) of the on-board wiring harness are already connected with a voltage distributor (11). The pink line (rs) of the new wiring harness (13) has to be connected with another voltage distributor (11) (wake-up line).

  6. Connect black, 6-pin connector to audio gateway control unit (N93/1).
    Fig 3: Connecting Black, 6-Pin Connector To Audio Gateway Control Unit (N93/1)
    G05030719Courtesy of MERCEDES-BENZ USA
  7. Connect black connector (17) of new adapter antenna line (14) to audio gateway control unit (N93/1).
  8. Connect black plug of new adapter antenna line (14) with black, on-board antenna connector.
    Fig 4: Connecting Black Connector Of New Adapter Antenna Line To Audio Gateway Control Unit (N93/1)
    G05030720Courtesy of MERCEDES-BENZ USA
  9. Remove insulation from branch-off line (17) of on-board wiring harness (7) until the left front door speaker group connector sleeve (+ signal) (Z28/5) and right front door speaker group connector sleeve (- signal) (Z28/8) is exposed.
  10. Separate the two lines that lead from the vehicle interior to the left front door speaker group connector sleeve (+ signal) (Z28/5) and the right front door speaker group connector sleeve (- signal) (Z28/8) at the particular connector sleeves.

    IMPORTANT The lines have a line cross section of 0.75 mm2 and a line cross section of 1.5 mm2 .

    The left front door speaker group connector sleeve (+ signal) (Z28/5) and right front door speaker group connector sleeve (- signal) (Z28/8) with the remaining line is no longer required.

    Fig 5: Removing Insulation From Branch-Off Line Of On-Board Wiring Harness
    G05030721Courtesy of MERCEDES-BENZ USA

    IMPORTANT The left front door speaker group connector sleeve (+ signal) (Z28/5) is assigned to three pink lines (rs).

    The right front door speaker group connector sleeve (- signal) (Z28/8) is assigned to three brown/white lines (br/ws).

    Fig 6: Connecting Pink Line (rs) To Pink Line (rs) Of New Speaker Wiring Harness
    G05030722Courtesy of MERCEDES-BENZ USA
  11. Connect pink line (rs) with a line cross section of 0.75 mm2 with a voltage distributor (11) to the pink line (rs) of the new speaker wiring harness (15).

    IMPORTANT Pink 2 line (rs) with a line cross section of 0.75 mm2 was connected to left front door speaker group connector sleeve (+ signal) (Z28/5). The new speaker wiring harness (15) has a black, 14-pin connector.

  12. Connect brown/white line (br/ws) with the line cross section of 0.75 mm2 with a voltage distributor (11) to the brown/black line (br/sw) of the new speaker wiring harness (15).

    IMPORTANT Brown/white line (br/ws) with the line cross section of 0.75 mm2 was connected to right front door speaker group connector sleeve (- signal) (Z28/8).

    IMPORTANT Branch-off line (20) consists of a yellow (ge), brown/yellow (br/ge), orange (or), and a brown (br) line; each of which is twisted in pairs. The have a line cross section of 0.75 mm2 .

    Branch-off line (20) will be routed rearward later in the right cable duct to the rear wall.

  13. Compare line colors of remaining 8 lines of on-board wiring harness (7) to remaining 8 lines of black, 14-pin connector of new speaker wiring harness (15) (lines are twisted in pairs).

    IMPORTANT If the colors are not identical  to the colors of the black, 14-pin connector, the connection has to be established via solder connector (12) as per variant 1  .

    VARIANT 1

    Black, 14-pin connector On-board wiring harness
    Cross section/color Cross section/color
    Socket 1 2.5 mm2 blue WITH 2.5 mm2 red/white
    Socket 2 2.5 mm2 red/white WITH 2.5 mm2 blue
    Socket 3 2.5 mm2 green WITH 2.5 mm2 red
    Socket 4 2.5 mm2 brown/green WITH 2.5 mm2 black
    Socket 7 1.5 mm2 pink WITH 1.5 mm2 pink
    Socket 8 1.5 mm2 brown/pink WITH 1.5 mm2 brown/pink
    Socket 13 1.5 mm2 white WITH 1.5 mm2 white
    Socket 14 1.5 mm2 brown/white WITH 1.5 mm2 brown/white

    IMPORTANT If the colors are identical  to the colors of the black, 14-pin connector, the connection has to be established via solder connector (12) as per variant 2  .

    VARIANT 2

    Black, 14-pin connector On-board wiring harness
    Cross section/color Cross section/color
    Socket 1 2.5 mm2 blue WITH 2.5 mm2 blue
    Socket 2 2.5 mm2 red/white WITH 2.5 mm2 red/white
    Socket 3 2.5 mm2 green WITH 2.5 mm2 green
    Socket 4 2.5 mm2 brown/green WITH 2.5 mm2 brown/green
    Socket 7 1.5 mm2 pink WITH 1.5 mm2 pink
    Socket 8 1.5 mm2 brown/pink WITH 1.5 mm2 brown/pink
    Socket 13 1.5 mm2 white WITH 1.5 mm2 white
    Socket 14 1.5 mm2 brown/white WITH 1.5 mm2 brown/white
  14. Connect black, 14-pin connector of new speaker wiring harness (15) to audio gateway control unit (N93/1).
  15. Route new speaker wiring harness (15) together with red line (rt) along existing lines at bracket (2) and attach with tie straps (see arrows).
  16. Attach all retrofitted wiring harnesses with felt tape (18) on the floor.
    Fig 7: Connecting Black, 14-Pin Connector Of New Speaker Wiring Harness To Audio Gateway Control Unit (N93/1)
    G05030723Courtesy of MERCEDES-BENZ USA
  17. Wind felt tape around all solder connections and crimp contacts.
  18. Route all retrofitted wiring harnesses as per the picture on the center tunnel and in the right footwell (see arrows).

    NOTES Ensure that the wiring harnesses are not routed in area (19), since this is where the footrest makes contact.

    Fig 8: Routing All Retrofitted Wiring Harnesses On Center Tunnel And In Right Footwell
    G05030724Courtesy of MERCEDES-BENZ USA
  19. Route branch-off line (20) of black, 14-pin connector of audio gateway control unit (N93/1) in right cable duct to right rear wall (see arrow).

    IMPORTANT Branch-off line (20) consists of an orange, a brown, a brown/ yellow, and a yellow line with a line cross section of 0.75 mm2 each.

    Fig 9: Routing Branch-Off Line Of Black, 14-Pin Connector Of Audio Gateway Control Unit (N93/1) In Right Cable Duct To Right Rear Wall
    G05030725Courtesy of MERCEDES-BENZ USA
  20. Expose the four on-board speaker lines for the rear speakers from the wiring harness on the rear wall.

    IMPORTANT The lines have a line cross section of 0.75 mm2 and are twisted in pairs. Since different line colors were installed, they have to be checked.

    The following color versions can be installed:

    Variant 1:  red/white twisted with blue, red twisted with black.

    Variant 2:  red/white twisted with blue, green twisted with green/brown.

    Fig 10: Identifying Four On-Board Speaker Lines
    G05030726Courtesy of MERCEDES-BENZ USA
  21. Separate the four on-board speaker lines.
  22. Connect the four on-board speaker lines (22), which are routed upward to the rear speakers, to one voltage distributor (11) each using the new lines of the branch-off line (20).

    IMPORTANT The on-board speaker lines (22) have to be connected, depending on the line colors, as per variant 1  or variant 2  .

  23. Fit on-board speaker lines (21) that are routed downward into the cable duct with one solder connector (12) each, wind felt tape around, and strap down in right cable duct.
    VARIANT 1

    On-board lines Branch-off line
    red/white WITH yellow
    Blue WITH brown/yellow
    Red WITH orange
    Black WITH brown
    VARIANT 2

    On-board lines Branch-off line
    red/white WITH brown/yellow
    Blue WITH yellow
    Green WITH orange
    green/brown WITH brown
scientia non olet · About LEMON Manuals