Remove/install and secure rear axle shaft twelve-point collar nut - AR35.30-P-0115-01A
REAR AXLE SHAFT
| Number | Designation | Model 129 | Model 170 | ||
|---|---|---|---|---|---|
| BA35.30-P-1001-01A | Collar nut, rear axle shaft to rear axle shaft flange | self-locking | Nm | - | - |
| not self-locking | Nm | 220 | 220 | ||
REAR AXLE SHAFT
| Number | Designation | Model 140 without special protection | Model 140 with special protection | ||
|---|---|---|---|---|---|
| BA35.30-P-1001-01A | Collar nut, rear axle shaft to rear axle shaft flange | self-locking | Nm | 350 | - |
| not self-locking | Nm | 320 | 390 | ||
REAR AXLE SHAFT
| Number | Designation | Model 202 | Model 203 | ||
|---|---|---|---|---|---|
| BA35.30-P-1001-01A | Collar nut, rear axle shaft to rear axle shaft flange | self-locking | Nm | - | - |
| not self-locking | Nm | 220 | 220 | ||
REAR AXLE SHAFT
| Number | Designation | Model 208 | Model 209 except 209.377/ 477, model 209 without code P98 | Model 209.377/ 477, model 209 with code P98 | ||
|---|---|---|---|---|---|---|
| BA35.30-P-1001-01A | Collar nut, rear axle shaft to rear axle shaft flange | self-locking | Nm | - | - | 350 |
| not self-locking | Nm | 220 | 220 | 320 | ||
REAR AXLE SHAFT
| Number | Designation | Model 210.0 without special protection | Model 210.0 with special protection | ||
|---|---|---|---|---|---|
| BA35.30-P-1001-01A | Collar nut, rear axle shaft to rear axle shaft flange | self-locking | Nm | - | 350 |
| not self-locking | Nm | 220 | 320 | ||
REAR AXLE SHAFT
| Number | Designation | Model 210.2/6 | Model 215 | Model 220 | ||
|---|---|---|---|---|---|---|
| BA35.30-P-1001-01A | Collar nut, rear axle shaft to rear axle shaft flange | self-locking | Nm | 350 | 350 | 350 |
| not self-locking | Nm | 320 | 320 | 320 | ||
REAR AXLE SHAFT
| Number | Designation | Model 211 | |||
|---|---|---|---|---|---|
| BA35.30-P-1001-01F | Collar nut, rear axle shaft to rear axle shaft flange | self-locking | Nm | 350 | |
| not self-locking | Stage 1 | Nm | 170 | ||
| Stage 2 | ∠° | 45 | |||
REAR AXLE SHAFT
| Number | Designation | Model 230 except 230.479 | |||
|---|---|---|---|---|---|
| BA35.30-P-1001-01F | Collar nut, rear axle shaft to rear axle shaft flange | self-locking | Nm | 350 | |
| not self-locking | Stage 1 | Nm | 170 | ||
| Stage 2 | ∠° | 45 | |||
REAR AXLE SHAFT
| Number | Designation | Model 230.479 with code P99 | Model 230.479 with code P99 | |||
|---|---|---|---|---|---|---|
| BA35.30-P-1001-01F | Collar nut, rear axle shaft to rear axle shaft flange | self-locking | Nm | - | - | |
| not self-locking | Stage 1 | Nm | 150 | 380 | ||
| Stage 2 | ∠° | 45 | - | |||
Detaching
- Apply parking brake
- Unscrew twelve-point collar nut (12).
The twelve-point collar nut (12) should be replaced each time it is unscrewed.
If a self-locking collar nut is mounted, the thread of the rear axle shaft is to be cleaned. Use suitable brush to remove residue of thread locking compound (arrow).
Mount on and secure
Only for thread M26: note twelve-point collar nut (12) variant. The non self-locking variant is replaced by the self-locking variant.
- Tighten twelve-point collar nut (12)
.
- Secure twelve-point collar nut (12) with caulker so that no gap remains between the groove and locking collar of the twelve-point collar nut.
Double lock twelve-point collar nut (arrows), for non self-locking variant. Lock twelve-point collar nut one time only, for self-locking variant.
- Release parking brake.