Remove/install wheels, rotate if necessary - AP40.10-P-4050Z

WARNING: This page is about a different car, the 2009 Mercedes-Benz E350 and 2008 Mercedes-Benz E350. However, it is still accessible from the selected car via links, so may be relevant.

MODEL 124, 129, 140, 164, 168, 170, 202, 203, 208, 209, 210, 211, 215, 220, 230, 240

MODEL 414

Left illustration

Fig 1: Identifying Wheel Lug Nut Tightening Sequence

Courtesy of MERCEDES-BENZ OF NORTH AMERICA.

Right figure

Fig 2: Turning Wheels (Vehicles Without Mixed Tires)

Courtesy of MERCEDES-BENZ OF NORTH AMERICA.

Fig 3: View Of Corrosion Protection Application Area Of Wheel Hubs

Courtesy of MERCEDES-BENZ OF NORTH AMERICA.

MODIFICATION NOTES

1.7.08

Apply corrosion protection to wheel contact surfaces and wheel hubs, added

Step 9

	Removing
	Risk of death caused by vehicle slipping or toppling off of the lifting platform.	Align vehicle between columns of vehicle lift and position four support plates at vehicle lift support points specified by vehicle manufacturer.	AS00.00-Z-0010-01A
1	Hoist vehicle with lifting platform until wheels are free
	Lift/jack up vehicle	Model 164	AR00.60-P-1000GZ
		Model 203, 209	AR00.60-P-1000P
		Model 211 Models 124, 129, 140, 168, 170, 202, 208, 210, 215, 220, 230, 240, 414	AR00.60-P-1000T
2	Pull off wheel covers	Vehicles with wheel covers
3	Unscrew wheel bolts and remove wheel-and-tire assemblies	Model 164, 240: Remove complete wheels with wheel lift
		Socket wrench Wheel lift/wheel lift truck gotis://F_40.1_06.0	*199589010900
	Wheel bolts modified	Model 210	BT40.10-P-0001-01A
	Measure
4	Measure depth of tread of all tires and note measured values on the maintenance sheet	Vehicles with spare tire: Perform measurement and all following checks on the spare tire as well. Measure depth of tread at point of greatest wear. Perform measurement at outside, inside and center of tread. Minimum depth of tread 1.6 mm. For safety reasons, tires should be replaced before the minimum depth of tread is reached: Conventional summer tires at approx. 2 to 3 mm tread depth Summer tires of PAX system at 3 mm tread depth Winter tires at approx. 4 mm tread depth
	Notes on measuring tire tread depth		AH40.10-P-0006-01T
		Brake pad gauge	*211589062300
	Check
5	Check tires for signs of damage and make sure that they are in good condition		AP40.10-P-4051Z
	Information on tires/rims		AH40.10-P-9411-01A
6	Check wheel bolts	The round contact shoulders on the lug bolts must be free of oil and grease. Replace wheel bolts with damaged thread, worn zinc coat on the radius seat or corroded radius seat otherwise these may shear off. Clean wheel bolts if necessary.
7	Check rims	Check for: Dirt to ensure that radius seats are free of oil and grease Damage to centering, radius seats and rim flanges Corrosion of contact surfaces Clean rims if necessary.
8	Check wheel hub, brake disk bowl at rim contact surface, and wheel bolt thread for contamination and corrosion	Contaminated or corroded wheel bolt thread must be cleaned or recut. Remaining contaminants or corrosion in the wheel bolt thread prevent reaching the necessary preload force of the wheel bolt, despite reaching the specified torque. The wheel hub should be replaced if the wheel bolt thread is damaged. Clean corroded surfaces with a wire brush or emery cloth.
	Install
9	Apply corrosion protection to wheel hubs and wheel contact surfaces (cross-hatched area)	Long-life grease	*BR00.45-Z-1001-06A
10	Change round wheel-and-tire assemblies on front and rear axles	If necessary, and only on vehicles without mixed tires. Retain running direction of wheels, as otherwise handling performances and comfort may be impaired and tire wear increased.
11	Slide on wheel-and-tire assemblies, and tighten the wheel bolts	Model 164, 240: Mount wheels with wheel lift.
		Observe the tightening sequence (1 to 5).
		Except model 164 and model 210 with code (979) Special protection version	*BA40.10-P-1001-01A
		Model 210 with code (979) Special protection version	*BA40.10-P-1001-01B
		Model 164	*BA40.10-P-1001-01J
		Socket wrench Wheel lift/wheel lift truck gotis://F_40.1_06.0	*199589010900
	Wheel bolts modified	Model 210	BT40.10-P-0001-01A
12	Lower vehicle
13	Correct tire pressure for all wheel-and-tire assemblies	In the event of tire pressure loss, determine cause and replace valve, tire or rim. On vehicles with tire pressure monitor: Install only valve protection caps made of plastic in order to avoid corrosion.
14	Fit wheel covers	Vehicles with wheel covers
	Check
15	Check expiry date of TIREFIT tire sealant	Vehicles fitted with TIREFIT	AP40.10-P-4054R
	TIREFIT tire sealant		AH40.10-P-0001-01A
16	Activate the tire pressure monitoring system	On vehicles with tire pressure monitor, wherever possible: Only when changing a wheel, tire change or change in tire pressure: ↓ Perform adjustments to the control system
		Model 164	AR54.30-P-1000-02GZA
		Model 211	AR54.30-P-1000-02RAT
		Model 215, 220	AR54.30-P-1000-02RAM
		Model 230	AR54.30-P-1000-02RAR
		Model 240	AR54.30-P-1000-02RAH
	Tire pressure monitor (RDK) activation	Model 210.074/274	GF40.15-P-0001-02A

WHEELS

Number	Designation			Model 210 with code 979
BA40.10-P-1001-01B	Wheel bolt	Version "A"	Nm	150
		Version "B"	Nm	110
		Version "C"	Nm	110
		See picture		BT40.10-P-0001-01A

WHEELS

Number	Designation		Model 124, 129, 168, 170, 171, 202, 208, model 210 without code 979	Model 140	Model 203
BA40.10-P-1001-01A	Wheel bolt	Nm	110	150	110

WHEELS

Number	Designation		Model 209 without code P98	Model 209 with code P98	Model 211	Model 215
BA40.10-P-1001-01A	Wheel bolt	Nm	110	130	130	150

WHEELS

Number	Designation		Model 220	Model 230	Model 240	Model 414
BA40.10-P-1001-01A	Wheel bolt	Nm	150	130	150	130

WHEELS

Number	Designation		Model 164
BA40.10-P-1001-01J	Wheel bolt	Nm	150

Fig 4: Identifying Socket Wrench (199 589 01 09 00)

Courtesy of MERCEDES-BENZ OF NORTH AMERICA.

Fig 5: Identifying Brake Pad Check Gauge (211 589 06 23 00)

Courtesy of MERCEDES-BENZ OF NORTH AMERICA.

REPAIR MATERIALS

Number	Designation	Order number
BR00.45-Z-1001-06A	Long-life grease	A 000 989 63 51 11