Breakdown assistance, function - GF82.95-P-2020CWU
MODEL 204.0 with CODE (359) TELE AID emergency call system
Function requirements
- Status "circuit 30 ON"
- Telematic Alarm Identification on Demand (emergency call system) (TELE AID) system authorized and operating error-free
- The vehicle-related breakdown assistance service is separately authorized
- An emergency call system control unit (N123/4) communication module authorized for the vehicle-related breakdown assistance service is configured ex-factory with the telephone number of the corresponding service provider
- The customer is registered and authorized in the Customer Assistance Center (CAC)
- A mobile telephone network is available in adequate strength and quality
- Triggering of breakdown assistance through pressing the breakdown assistance button (S93/6s2) > 0.5 s
- A higher-priority vehicle-related service is not active
Depending on equipment installed one of the following control units is installed:
- COMAND controller unit (A40/3), with code (512) COMAND APS with DVD changer
- Radio (A2), with code (494) USA version
- Radio, with code (510) Audio 20 with CD changer
The function description uses the term "master control unit".
General
The breakdown assistance function enables the customer to, e.g. make contact with the CAC in the event of a problem with the vehicle. The CAC can then perform remote diagnosis for the actual situation and initiate effective help measures, taking into consideration further vehicle-specific data.
The breakdown assistance function consists of the two following subfunctions:
- Breakdown assistance function sequence
- Function sequence for display of additional services
Breakdown assistance function sequence
The breakdown assistance button is read in directly by the emergency call system control unit via a discrete line. The emergency call system control unit automatically transmits an SMS with the following data to the CAC via the communication module integrated into the emergency call system control unit:
- Vehicle position
- Customer identification data
- Vehicle identification data
- Condition data
A voice connection to the CAC is also set up via the communication module integrated into the emergency call system control unit.
The communication module integrated into the emergency call system control unit transmits and receives the mobile phone signals or data in the following way:
- Discrete line
- Frequency switchover control unit (N96), with code (389) Mobile phone preinstallation with universal interface, USA/ Canada
- Discrete line
- Multifunction antenna (A28/11)
The light emitting diode (LED) integrated into the breakdown assistance button flashes as long as the breakdown assistance is active.
In the event of a breakdown assistance event, other vehicle-related services (e.g. MB-Info call) and, for vehicles with code (389) Mobile phone preinstallation with universal interface, USA/Canada, active mobile phone connections are interrupted.
In the event of a malfunction in the multifunction antenna (e.g. defective because of a rollover), the communication module integrated into the emergency call system control unit automatically sends and receives the mobile phone signals and data via the emergency call system antenna (A2/52).
Function sequence for display of additional services
Also available are the following services which are shown on the Audio/COMAND display (A40/8):
- Destination Feed In (transmission of destinations which can then be actuated using the navigation system), with code (512) COMAND APS with DVD changer
- Freetext (transmission of text messages)
The other services, e.g. Freetext (transmission of text messages), are sent to the Audio/COMAND display by the emergency call system control unit in the following way:
- Diagnostic CAN
- Front SAM control unit with fuse and relay module (N10/1)
- Interior CAN
- "Master control unit"
- Low Voltage Differential Signaling (LVDS) line
| Electrical function diagram for TELEAID TELEDIAGNOSIS | With code (389) Mobile phone preinstallation with universal interface, USA/Canada Comfort telephony | PE82.95-P-2060-99FAA | |
| Telephone and GPS roof antenna component description | A28/11 | GF82.62-P-4119CW | |
| Frequency switchover control unit, component description | N96 With code (389) Mobile phone preinstallation with universal interface, USA/Canada Comfort telephony |
GF82.62-P-4204CWU | |
| MB-Info and breakdown assistance button group, component description | S93/6s1, S93/6s2 | GF82.95-P-3211CWU | |
| Emergency call system control unit, component description | N123/4 | GF82.95-P-3212CWU | |
| Emergency call system backup antennas component description | A2/52 | GF82.95-P-4002CWU |