Route wiring harness and connect - AZ54.65-P-0001-06CW

REPAIR MATERIALS

Number	Designation	Order number
BR00.45-Z-1075-02A	Teroson double-sided adhesive tape For bonding trim strips and emblems (UV-resistant and weatherproof, black) (Width: 12 mm) Order no.: 107.64 A (Width: 19 mm) Order no.: 107.96 K (Width: 25 mm) Order no.: 117.05 Y

Fig 1: Identifying Wiring Harness

Courtesy of MERCEDES-BENZ USA

Contact clutch control unit (7) at the quickpark control unit (1).
Attach quickpark control unit (1) to the side piece with double-sided adhesive tape.
Bonding surfaces must be pretreated in accordance with adhesive tape manufacturer's instructions.

Fig 2: Identifying Quick Park Control Unit
Courtesy of MERCEDES-BENZ USA
Connect ground connection (8) to ground point, luggage compartment (right taillamp) (W7/1).

Fig 3: Identifying Luggage Compartment Right Taillamp
Courtesy of MERCEDES-BENZ USA
Contact line lacing of power supply with fuse holder (10) on rear SAM control unit with fuse and relay module (N10/2) at slot 59.
The connector is color coded.

Fig 4: Identifying Rear SAM Control Unit Fuse Holder And Relay Module
Courtesy of MERCEDES-BENZ USA
Pry off rear shelf cover and, using a suitable tool, cut a cutout the size of the warning tone speaker (2) in the rear shelf. Guide the line of the warning tone speaker (2) through the existing opening in the luggage compartment. Attach double-sided adhesive tape to the complete back face of the warning tone speaker (2) and stick on the warning tone speaker (2).
Bonding surfaces must be pretreated in accordance with adhesive tape manufacturer's instructions.

Fig 5: Identifying Rear Shelf Warning Tone Speaker
Courtesy of MERCEDES-BENZ USA
Fix the line of the warning tone speaker in position with adhesive tape and route to the quickpark control unit. Contact the line of the warning tone speaker with "average" warning tone volume.
Depending on the fitting point or customer request the warning tone volume can be switched over to "Loud" or "Quiet".

Fig 6: Identifying Relay Module
Courtesy of MERCEDES-BENZ USA
Remove rubber plug from the opening in the trunk floor. Route quickpark wiring harness (6) outwards through the opening and seal the opening with the rubber grommet (arrow) attached to the sensor wiring harness.
Route sensor wiring harness to the bumper reinforcement and fasten with cable ties in a manner which is free from chafing and noise.
Connect the connectors to the sensors with the rubber seals of the sensor wiring harness.
The rubber seals must be installed over the sensor connectors so that the connections are watertight.

Fig 7: Identifying Housing Connector
Courtesy of MERCEDES-BENZ USA
Loosen yellow housing connector 9 I (arrow) on rear SAM control unit with fuse and relay module (N10/2) and take off.

Fig 8: Identifying SAM Control Unit Relay Module
Courtesy of MERCEDES-BENZ USA
Remove black contact carrier (arrow) from the yellow housing connector.

Fig 9: Identifying Contact Carrier
Courtesy of MERCEDES-BENZ USA
Unpin brown line from black contact carrier, contact cavity 31 and pin into contact cavity 2 of the housing connector CAN (13) supplied. Pin the brown CAN line (br) of the Quickpark wiring harness into contact cavity 31 of the black contact carrier.
Unpin brown/red CAN line from the black contact carrier, contact cavity 30 and pin into contact cavity 1 of the housing connector CAN (13) supplied. Pin brown/red CAN line of the Quickpark wiring harness into contact cavity 30 of the black contact carrier.
Contact CAN coupling (13) on the vehicle's own wiring harness with the CAN plug (12) of the Quickpark cable lacing.
Install black contact carrier in yellow housing connector and contact with the rear SAM control unit with fuse and relay module (N10/2).

Fig 10: Identifying CAN Plug And Housing Connector CAN

Courtesy of MERCEDES-BENZ USA